Just prompt explaination: > - no modparams in config no uac modparams in config.
> - route[0] is responsible for basic routing > - route[5] is for proper call distribution by using lookup(location) > information. In the same route i have implemented calling number > modification. > Just before the end of route i am arming t_relay with failure route > (in case of busy for instance). > - failure_route[105] is to do_routing the call to VM service outside > the opensips. But just before t_relaying here i need to restore the > original $fU. > According to http://www.opensips.org/html/docs/modules/1.6.x/uac.html#id292928 > i should use uac_restore_from() command (with default restore_mode > modparam). > Unfortunately the calling number once replaced cannot be restored in my case. > Below you may find a snippet from debug > > Number replacing is generating vsf param > /sbin/opensips[28268]: DBG:uac:w_replace_from: dsp=0xffd3f38c (len=0) > , uri=0xffd3f394 (len=29) > /sbin/opensips[28268]: DBG:uac:replace_uri: removing display ["unknown"] > /sbin/opensips[28268]: DBG:uac:replace_uri: uri to replace > [sip:[email protected]] > /sbin/opensips[28268]: DBG:uac:replace_uri: replacement uri is > [sip:[email protected]] > /sbin/opensips[28268]: DBG:uac:replace_uri: encode > is=<AAAAAAIJAgUMBAEAD3AHeQUXBR8FHwUaCRoKHAsyOQ--> len=44 > /sbin/opensips[28268]: DBG:rr:add_rr_param: adding > (;vsf=AAAAAAIJAgUMBAEAD3AHeQUXBR8FHwUaCRoKHAsyOQ--) 0x81c2828 > > then opensips constucts Busy message and in the same time without any > uac_restore_from() command: > /sbin/opensips[28795]: DBG:uac:restore_uri_reply: removing > <<sip:[email protected]>> > /sbin/opensips[28795]: DBG:uac:restore_uri_reply: inserting <"unknown" > <sip:[email protected]>> > > then the call failes to failure_route[105] and uac_restore_from() is > generating following debug > /sbin/opensips[28797]: DBG:uac:restore_uri: getting 'vsf' Route param > /sbin/opensips[28797]: DBG:uac:restore_uri: route param 'vsf' not found > just after that the call is hitting do_routing and t_relay to VM > server. Of course calling number was not restored to original one. > > Could You please point me where the problem is located? > Just one more info - calling number modification part of config is > located in separated route[10] to be used whenever i wish in my > script. > > Thx, > Maciej. > > >> Bogdan, Stefano, >> >> Its working as is should :) >> Thanks for pointing me to the right function. >> >> Maciej. >> >> 2010/10/11 Bogdan-Andrei Iancu <[email protected]>: >>> To be more precise: >>> http://www.opensips.org/html/docs/modules/1.6.x/uac.html#id228582 >>> >>> Regards, >>> Bogdan >>> >>> Stefano Pisani wrote: >>>> Use replace_from :-) >>>> >>>> ciao >>>> s >>>> >>>> Il 10/10/2010 19:19, Maciej Bylica ha scritto: >>>> >>>>> Hello >>>>> >>>>> I have a question regarding $fU pseudo variable. >>>>> As mentioned at http://www.opensips.org/Resources/DocsCoreVar16 and on >>>>> the basis of opensips outputs: >>>>> ERROR:dialplan:dp_trans_fixup: the output PV is read-only!! >>>>> it clearly means that $fU is read-only. >>>>> >>>>> Unfortunately it is quite big problem for me, because what im >>>>> struggling with is to achieve proper calling number presentation. >>>>> In my scenario all endpoints located in subscriber table do have full >>>>> username with country code, so there are for instance: >>>>> - 48111223344 (48 country code) >>>>> - 49222334455 (49 country code) >>>>> - 44333445566 (44 country code) >>>>> ... >>>>> >>>>> If there is a national call inside the 48 country code the calling >>>>> number should be changed by striping first two digits (48) - >>>>> 48999887766--->999887766 >>>>> In case of international call, i should add two digits (00) - >>>>> 49222334455--->0049222334455. >>>>> >>>>> I am using diaplan module in this case and following entry gives me >>>>> the error I mentioned. >>>>> dp_translate("2", "$fU/$fU"); >>>>> >>>>> If there are any workaround. >>>>> Any help would be highly appreaciated. >>>>> >>>>> Thanks, >>>>> Maciej >>>>> >>>>> _______________________________________________ >>>>> Users mailing list >>>>> [email protected] >>>>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users >>>>> >>>> >>>> >>>> _______________________________________________ >>>> Users mailing list >>>> [email protected] >>>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users >>>> >>>> >>> >>> >>> -- >>> Bogdan-Andrei Iancu >>> OpenSIPS Bootcamp >>> 15 - 19 November 2010, Edison, New Jersey, USA >>> www.voice-system.ro >>> >>> >>> _______________________________________________ >>> Users mailing list >>> [email protected] >>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users >>> >> > _______________________________________________ Users mailing list [email protected] http://lists.opensips.org/cgi-bin/mailman/listinfo/users
