Hi Jose, This option is not set in my config but actually I managed to figure out things using the "ie" and "ei" flags in the rtpproxy_offer/rtpproxy_answer fonctions. Thanks for your help !
Best Regards, Sebastien Le 08/11/2010 10:16, jose luis millan a écrit : > Hi Sebastien, > > Is the 'mhomed' option set in your configuration file? > > regards. > > > On Sun, Nov 7, 2010 at 2:53 PM, Sebastien CRUAUX<[email protected]> wrote: >> I'm getting the same problem with RTP packets... Maybe some issue with >> rtpproxy bridging mode ? >> >> >> >> Le 05/11/2010 11:21, Vallimamod ABDULLAH a écrit : >>> Hi, >>> >>> Have a look at force_send_socket >>> (http://www.opensips.org/Resources/DocsCoreFcn#toc103) >>> >>> Regards, >>> - vma >>> . >>> >>> On Nov 5, 2010, at 11:10 AM, Sebastien CRUAUX wrote: >>> >>>> Hi, >>>> >>>> I'm encountering some issue with my Opensips configuration. >>>> My Opensips server is configured to relay SIP MESSAGE requests to >>>> another server when the destination URI is not located on my server. >>>> Here is the part of opensips.cfg which is concerned : >>>> >>>> if (!lookup("location","m")) { >>>> >>>> switch ($retcode) { >>>> case -1: >>>> case -3: >>>> rewritehost("10.254.230.148"); >>>> if (is_method("MESSAGE")) { >>>> rewriteport("5062"); >>>> } >>>> if (!t_relay()) { >>>> sl_reply_error(); >>>> } exit; >>>> case -2: >>>> sl_send_reply("405", "Method Not Allowed"); >>>> exit; >>>> } >>>> } >>>> >>>> My server receives SIP requests on eth0 interface (IP 10.254.31.45) but >>>> when it relays the requests to the server 10.254.230.148 it should use >>>> eth2 IP (10.254.28.45) as src IP because there is a firewall between the >>>> two servers and port 5062 is only allowed for source IP 10.254.28.45. >>>> The problem is the following : when I open Wireshark on my Opensips >>>> server, I can see that the source IP for the relayed MESSAGE is still >>>> 10.254.31.45 so it never reaches the other server ! I don't understand >>>> where is the issue, my Linux routing table is OK, when I'm trying to >>>> reach 10.254.230.148 from my Opensips server using telnet for example it >>>> uses the right interface and the right gateway. Here is my routing table : >>>> >>>> 10.254.230.144 10.254.28.1 255.255.255.240 UG 0 0 0 eth2 >>>> 10.254.31.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 >>>> 10.254.28.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 >>>> 10.254.29.0 0.0.0.0 255.255.255.0 U 0 0 0 eth3 >>>> 192.168.0.0 10.254.28.1 255.255.255.0 UG 0 0 0 eth2 >>>> 10.254.225.0 10.254.28.1 255.255.255.0 UG 0 0 0 eth2 >>>> 0.0.0.0 10.254.31.1 0.0.0.0 UG 0 0 0 eth0 >>>> >>>> Did I miss something in Opensips configuration file ? >>>> Thanks a lot for your help. >>>> >>>> Best Regards, >>>> >>>> Sebastien >>>> >>>> >>>> >>>> _______________________________________________ >>>> Users mailing list >>>> [email protected] >>>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users >>> _______________________________________________ >>> Users mailing list >>> [email protected] >>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users >> >> >> _______________________________________________ >> Users mailing list >> [email protected] >> http://lists.opensips.org/cgi-bin/mailman/listinfo/users >> > _______________________________________________ > Users mailing list > [email protected] > http://lists.opensips.org/cgi-bin/mailman/listinfo/users _______________________________________________ Users mailing list [email protected] http://lists.opensips.org/cgi-bin/mailman/listinfo/users
