Thank you Bogdan. That answers all my questions. Regards, Ali Pey
On Wed, Aug 29, 2012 at 12:37 PM, Bogdan-Andrei Iancu <[email protected]>wrote: > ** > Hi Ali, > > For profiling, use the GW ID - as value for the profile - (you can > instruct DR to return the GW ID in an AVP) ; now, about the limit, use the > "attrs" from GWs to keep it > > Regards, > > Bogdan-Andrei Iancu > OpenSIPS Founder and Developerhttp://www.opensips-solutions.com > > > On 08/29/2012 07:35 PM, Ali Pey wrote: > > Hi Jeff, > > Thank you for the reply but unfortunately this doesn't answer my > questions. I need to bind this to the drouting module, so when I call > do_routing, I need a parameter for set_dialog_profile for whatever gateway > do_routing() picks. That was my first and second questions. > > Also in your case, where do you set $var(dlgsize_out)? where do you get > it from? How would you change it? I don't want to have to change my script > or restart opensips to change this. > > Regards, > Ali Pey > > > On Wed, Aug 29, 2012 at 12:27 PM, Jeff Pyle <[email protected]>wrote: > >> Ali, >> >> Oops, I had some inconsistent rewrites. So much for improved >> readability. Consider this instead: >> >> # Check to see if we're at maximum capacity for this gateway >> if !(get_profile_size("outbound", "$avp(s:dlgid_out)", >> "$var(dlgsize_out)")) { >> xlog("L_INFO", "Couldn't get dialog size, continuing >> route-out\n"); >> } else { >> if (is_avp_set("$avp(s:gw_maxcalls)") && >> $var(dlgsize_out) >= $avp(s:gw_maxcalls)) { >> # We're full, so cycle around to the next >> gateway... >> } >> } >> >> That should make more sense. >> >> >> - Jeff >> >> >> >> >> On Wed, Aug 29, 2012 at 12:24 PM, Jeff Pyle <[email protected]>wrote: >> >>> Hi Ali, >>> >>> I have the same application. A little before the t_relay() to the >>> gateway, I have: >>> >>> # Check to see if we're at maximum capacity >>> if !(get_profile_size("outbound", "$avp(s:dlgid_out)", >>> "$var(dlgsize_out)")) { >>> xlog("L_INFO", "Couldn't get dialog size, continuing >>> route-out\n"); >>> } else { >>> if (is_avp_set("$avp(s:gw_maxcalls)") && >>> $var(dlgsize_out) >= $avp(s:car_maxcalls)) { >>> # Move on to the next carrier... >>> >>> } >>> } >>> # Continue towards t_relay() for this gateway... >>> >>> This verifies our counts to make sure we have room. If I'm at that >>> value (or over) I cycle around and select the next gateway. If all is well >>> I run set_dlg_profile("outbound", "$avp(s:dlgid_out)"). Since you're >>> using drouting, perhaps you'll use another variable here in place of >>> $avp(s:dlgid_out). >>> >>> I implement serial forking for my gateways. In the selected >>> failure_route I run unset_dlg_profile("outbound", "$avp(s:dlgid_out)"). >>> If I'm in this section I know the call has failed, so I want to remove its >>> count from the profile. >>> >>> This configure is old enough to be pre-drouting but the concepts are >>> still the same. >>> >>> Is that helpful? >>> >>> >>> - Jeff >>> >>> >>> >>> On Wed, Aug 29, 2012 at 11:53 AM, Ali Pey <[email protected]> wrote: >>> >>>> Hi All, >>>> >>>> I would like to limit number of concurrent calls to a gateway in >>>> dr_gateways table (drouting module). >>>> >>>> I have looked at the tutorial on the opensips webiste ( >>>> http://www.opensips.org/Resources/DocsTutConcurrentCalls) and this is >>>> not the same. >>>> >>>> I do create a dialog and then I do do_routing(). At this point I >>>> don't know: >>>> >>>> 1- What parameters to pass to set_dlg_profile() to increase the >>>> number of calls for whatever particular gateway do_routing happened to >>>> select? >>>> >>>> 2- How to use get_profile_size() to see if the gateway has reached >>>> it's maximum number of channels? >>>> >>>> 3- Where would be the best place to record and read the max number of >>>> channels available for each gateway? some place that I wouldn't need to do >>>> a db quey but I would be able to make changes while opensips is running >>>> similar to the drouting module parameters itself. >>>> >>>> >>>> Any help/suggestion would be appreciated. >>>> >>>> Thanks, >>>> Ali Pey >>>> >>>> >>>> _______________________________________________ >>>> Users mailing list >>>> [email protected] >>>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users >>>> >>>> >>> >> >> _______________________________________________ >> Users mailing list >> [email protected] >> http://lists.opensips.org/cgi-bin/mailman/listinfo/users >> >> > > _______________________________________________ > Users mailing > [email protected]http://lists.opensips.org/cgi-bin/mailman/listinfo/users > > > _______________________________________________ > Users mailing list > [email protected] > http://lists.opensips.org/cgi-bin/mailman/listinfo/users > >
_______________________________________________ Users mailing list [email protected] http://lists.opensips.org/cgi-bin/mailman/listinfo/users
