Hi, Khaled!
After your loose_route() call, you should do something like this:
if ($DLG_status == NULL)
xlog("ERROR: $rm not matched\n");
Best regards,
Răzvan Crainea
OpenSIPS Core Developer
http://www.opensips-solutions.com
On 04/24/2014 11:25 AM, M.Khaled W Chehab wrote:
HI Razvan,
Yes I am using Dialog with topology hiding ,how can I check the matching for
ACK and BYE between opensips and gateway, I have a wireshark capture for both
legs .
Regards
-----Original Message-----
From: [email protected]
[mailto:[email protected]] On Behalf Of Razvan Crainea
Sent: Wednesday, April 16, 2014 5:39 PM
To: [email protected]
Subject: Re: [OpenSIPS-Users] Acc module /Bug
Hi, Khaled!
You should first check what is the problem with that ACK that is ignored by the
Gateway. I presume you are using dialog support and most likely, the ACK and
the BYE are not matched by OpenSIPS.
Best regards,
Razvan Crainea
OpenSIPS Core Developer
http://www.opensips-solutions.com
On 04/16/2014 12:26 PM, M.Khaled W Chehab wrote:
Hi,
I notice that opensips is not hanging up the call when a bye is
received from client as it forward the BYE to gateway and gateway send
a 200 ok back ,
furthermore i can see a bad behavior from gateway which is opensips
forward the ACK from UA after 200 OK with SDP is received from
gateway to gateway and the gateway send again and again 200 ok with
SDP , besides opensips forward it to client and reply back to gateway
with ACK 10 times
Problem: When opensips receive a bye from UA it does not hang-up
the call and wait till max call duration to send a bye to gateway
then gateway reply by 481 transaction does not exist ,and the record
stored in acc table
can this be a bug , I am using
version: opensips 1.10.0-notls (x86_64/linux)
flags: STATS: Off, EXTRA_DEBUG, USE_IPV6, USE_TCP, DISABLE_NAGLE,
USE_MCAST, SHM_MEM, SHM_MMAP, PKG_MALLOC, F_MALLOC,
FAST_LOCK-ADAPTIVE_WAIT
ADAPTIVE_WAIT_LOOPS=1024, MAX_RECV_BUFFER_SIZE 262144, MAX_LISTEN 16,
MAX_URI_SIZE 1024, BUF_SIZE 65535
poll method support: poll, epoll_lt, epoll_et, sigio_rt, select.
@(#) $Id$
main.c compiled on 13:21:19 Oct 24 2013 with gcc 4.7
please advise
regards
*From:*M.Khaled W Chehab [mailto:[email protected]]
*Sent:* Tuesday, April 15, 2014 4:24 PM
*To:* ([email protected]); ([email protected])
*Subject:* Acc module
Hi
I have a problem with accc modules with the below scenario :
OPENSIPS receive the 200 ok from the trunk gateway ,and forward it
to UA,
UA replies by ACK and opensips forward this ACK to Gateway ,..but for
some reason the Gateways resends a lot of 200 OK with SDP and opensips
relay these packets to UA and UA replies with ACK …..
*Problem: Acc module set the call duration to 3600 seconds which is
the max call duration *
By wire shark i can see that UA is sending a bye after 2 minutes and
opensips relay the BYE to Gateway moreover trunk gateway is sending
back 200 OK to confirm the bye and it ends the call
But in mysql acc rows , acc module store the call duration to max
call duration(3600)
How can I fix this ,please advice
Regards
_______________________________________________
Users mailing list
[email protected]
http://lists.opensips.org/cgi-bin/mailman/listinfo/users
_______________________________________________
Users mailing list
[email protected]
http://lists.opensips.org/cgi-bin/mailman/listinfo/users
_______________________________________________
Users mailing list
[email protected]
http://lists.opensips.org/cgi-bin/mailman/listinfo/users
_______________________________________________
Users mailing list
[email protected]
http://lists.opensips.org/cgi-bin/mailman/listinfo/users
