Rik, thatis correct.
Checking the codeon howa destination may end up as inactive,these are
the options:
- via MI ds_set_state command
- via the script "ds_mark_dst" function
- read from "flags" inDB at startup.
So, which one are you using ?
Regards,
Bogdan-Andrei Iancu
OpenSIPS Founder and Developer
http://www.opensips-solutions.com
On 10.06.2014 14:25, Rik Broers wrote:
I do have ds_probing_mode set to 1.
According to documentation it is able to change states from Active to
Probing. Nowhere the state Inactive is mentioned for this param.
The probing works as expected. If the OPTIONS remain unanswered the
status is changed to Probing. When the destination starts replying
again it changes back to active.
Probing as initial state (after startup) would be less of a problem as
they will then automatically go to Active based on OPTIONS monitoring.
Destinations with Inactive state will not be pinged and are unable to
get to an Active or Probing state without an opensipsctl fifo
ds_set_state.
Vriendelijke groet,
*Rik Broers*
Voice Engineer
*Van:*Bogdan-Andrei Iancu [mailto:[email protected]]
*Verzonden:* dinsdag 10 juni 2014 13:02
*Aan:* Rik Broers; OpenSIPS users mailling list
*Onderwerp:* Re: [OpenSIPS-Users] Dispatcher nodes start as Inactive
Hi Rik,
Do you set the "ds_probing_mode" param ? Maybe you start with the
destination as active, but because of that param (when set to 1), the
probing is permanent and the destinations may be learned as inactive
(based on probing).
Regards,
Bogdan-Andrei Iancu
OpenSIPS Founder and Developer
http://www.opensips-solutions.com
On 10.06.2014 13:06, Rik Broers wrote:
I’ve tried putting 0 in the flags column, They still start as
Inactive. Strange thing is that not all of them start as inactive?
Opensips –V output below:
version: opensips 1.10.1-notls (x86_64/linux)
flags: STATS: On, USE_IPV6, USE_TCP, DISABLE_NAGLE, USE_MCAST,
SHM_MEM, SHM_MMAP, PKG_MALLOC, F_MALLOC, FAST_LOCK-ADAPTIVE_WAIT
ADAPTIVE_WAIT_LOOPS=1024, MAX_RECV_BUFFER_SIZE 262144, MAX_LISTEN
16, MAX_URI_SIZE 1024, BUF_SIZE 65535
poll method support: poll, epoll_lt, epoll_et, sigio_rt, select.
git revision: f03f552
@(#) $Id$
main.c compiled on 11:28:31 May 19 2014 with gcc 4.4.5
Vriendelijke groet,
*Rik Broers*
Voice Engineer
*Van:*Bogdan-Andrei Iancu [mailto:[email protected]]
*Verzonden:* dinsdag 27 mei 2014 11:33
*Aan:* Rik Broers; [email protected]
<mailto:[email protected]>
*Onderwerp:* Re: [OpenSIPS-Users] Dispatcher nodes start as Inactive
Hi Rik,
yes, I have to agree about the docs - it needs to be done.
Put 0 for the flags - that means is active .
Regards,
Bogdan-Andrei Iancu
OpenSIPS Founder and Developer
http://www.opensips-solutions.com
On 27.05.2014 11:43, Rik Broers wrote:
So i can use the following values in the Flags column?
·/"i", "I" or "0"/- the last destination should be set to
inactive and will be ignored in future requests.
·/"a", "A" or "1"/- the last destination should be set to active.
·/"p", "P" or "2"/- the last destination will be set to
probing. Note: You will need to call this function
"threshhold"-times, before it will be actually set to probing.
I don’t find this to be very clear from the documentation, as
there also is the modparam named flags which does not seem to
do anything with Flags in the DB.
No where there is specifically noted what values you can use
for the different columns.
Vriendelijke groet,
*Rik Broers*
Voice Engineer
*Van:*Bogdan-Andrei Iancu [mailto:[email protected]]
*Verzonden:* maandag 26 mei 2014 20:00
*Aan:* [email protected]
<mailto:[email protected]>; Rik Broers
*Onderwerp:* Re: [OpenSIPS-Users] Dispatcher nodes start as
Inactive
Hi Rik,
In 1.10, upon restart, the status flags from DB are loaded
(the in memory state is discarded) - so check the flags you
have for the destinations in DB.
Regards,
Bogdan-Andrei Iancu
OpenSIPS Founder and Developer
http://www.opensips-solutions.com
On 26.05.2014 09:55, Rik Broers wrote:
When I restart my 1.10 opensips a lot of the dispatcher
nodes start as Inactive.
I have to manually set them to P or A before they become used.
How can I make sure all nodes start as Probing or Active
after a server reboot.
Vriendelijke groet,
*Rik Broers*
Voice Engineer
_______________________________________________
Users mailing list
[email protected] <mailto:[email protected]>
http://lists.opensips.org/cgi-bin/mailman/listinfo/users
_______________________________________________
Users mailing list
[email protected]
http://lists.opensips.org/cgi-bin/mailman/listinfo/users
