Hello Bogdan-Andrei, I ran some traffic without rtpengine and with the codec operations, i did not got any core files. I will take care of not combining those commands.
Thanks and regards. Mario On Thu, Oct 21, 2021 at 7:26 AM Bogdan-Andrei Iancu <[email protected]> wrote: > Hi Mario, > > So you do both rtpengine ops and codecs ops in your cfg. This is a bit of > a receipt for disaster (as both are independently changing the SDP), still > not for a crash. > > Could you try to run both codec ops, but without rtpengine, just to see if > ok ? > > Regards, > > Bogdan-Andrei Iancu > > OpenSIPS Founder and Developer > https://www.opensips-solutions.com > OpenSIPS eBootcamp 2021 > https://opensips.org/training/OpenSIPS_eBootcamp_2021/ > > On 10/19/21 7:20 PM, Mario San Vicente wrote: > > Hello Bogdan-Andrei, > > I removed the following lines and it is working fine now. Not sure if the > issue was one or the combination of those 2 lines that made opensips crash. > > #codec_delete_re("PCMA|PCMU"); > #codec_delete_except_re("speex"); > > The reason for using those lines was that opensips was doing transcoding > and after a while it stops doing the transcode, it just was bypassing the > original codec offer. This is also solved, the problem is that > the rtpengine_offer was not closing properly and then i ran out of ports. > The solution was to add rtpengine_delete(); at the failure route. > > > Thank you all for your help! > > Regards. > Mario > > On Tue, Oct 19, 2021 at 2:01 AM Bogdan-Andrei Iancu <[email protected]> > wrote: > >> Hi Mario, >> >> What is the codec relate operation you do from the script? As it looks it >> is crashing there. >> >> Regards, >> >> Bogdan-Andrei Iancu >> >> OpenSIPS Founder and Developer >> https://www.opensips-solutions.com >> OpenSIPS eBootcamp 2021 >> https://opensips.org/training/OpenSIPS_eBootcamp_2021/ >> >> On 10/19/21 12:15 AM, Mario San Vicente wrote: >> >> Thank you Giovany . >> >> I got some info, but I'm not sure how to proceed.... Looks like an issue >> assigning core vars.. Here the whole info in a txt file. >> >> >> {rs = {s = 0x6dc2d4a3fa5df100 <error: Cannot access memory at address >> 0x6dc2d4a3fa5df100>, >> sval = {s = 0x100000002 <error: Cannot access memory at address >> 0x100000002>, len = -1510612476} >> >> Thank your comments. >> >> On Mon, Oct 18, 2021 at 12:39 PM Giovanni Maruzzelli <[email protected]> >> wrote: >> >>> On Mon, Oct 18, 2021 at 7:01 PM Mario San Vicente < >>> [email protected]> wrote: >>> >>>> Hello Ovidiu, >>>> >>>> That works for getting the core files. Then i run the command bt full >>>> and got the following: >>>> >>>> >>> You must install the opensips-dbg debian package, it contains the >>> symbols, then restart opensips, then retake the core and you'll see info in >>> it. >>> >>> -giovanni >>> >>> -- >>> Sincerely, >>> >>> Giovanni Maruzzelli >>> OpenTelecom.IT >>> cell: +39 347 266 56 18 >>> >>> _______________________________________________ >>> Users mailing list >>> [email protected] >>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users >>> >> >> >> -- >> Mario San Vicente >> Cheers! >> >> _______________________________________________ >> Users mailing >> [email protected]http://lists.opensips.org/cgi-bin/mailman/listinfo/users >> >> >> > > -- > Mario San Vicente > Cheers! > > > -- Mario San Vicente Cheers!
_______________________________________________ Users mailing list [email protected] http://lists.opensips.org/cgi-bin/mailman/listinfo/users
