Hello Bogdan.
What we need is to advertise different IP for the same interface different IP based on Client Source IP. For example OpenSIPs Interface IP is 10.0.0.10 and NAT IP is 1.2.3.4 When Client IP is 10.0.0.100 we need to advertise 10.0.0.10 When Client IP is 4.3.2.1 we need to advertise 1.2.3.4 Thank you once more for your support Best regards Antonis Psaras From: Bogdan-Andrei Iancu <bog...@opensips.org> Sent: Πέμπτη, 3 Απριλίου 2025 09:57 To: apsa...@microbase.gr; 'OpenSIPS users mailling list' <users@lists.opensips.org>; 'Johan De Clercq' <jo...@democon.be> Subject: Re: [OpenSIPS-Users] mhomed OpenSIPs behind NAT - How to control NAT IP Hi, You can have a socket on the private interface (behind NAT) which is advertising in the outbound SIP packages a different IP address (the public IP of the NAT , for example) than the one of the socket. Isn't this what you were asking for? Regards, Bogdan-Andrei Iancu OpenSIPS Founder and Developer https://www.opensips-solutions.com https://www.siphub.com On 02.04.2025 15:32, Antonios Psaras wrote: Thank you Bogdan. I can not see how advertise option will be use in that case. We use the socket option and my question is if I can handle that within the script. Ie. socket = udp:10.0.0.10:5060 as 1.2.3.4:5060 if source_ip=~”^10.” Do not use NAT IP on header else User it. From: Bogdan-Andrei Iancu <mailto:bog...@opensips.org> <bog...@opensips.org> Sent: Τετάρτη, 2 Απριλίου 2025 15:03 To: apsa...@microbase.gr <mailto:apsa...@microbase.gr> ; OpenSIPS users mailling list <mailto:users@lists.opensips.org> <users@lists.opensips.org>; 'Johan De Clercq' <mailto:jo...@democon.be> <jo...@democon.be> Subject: Re: [OpenSIPS-Users] mhomed OpenSIPs behind NAT - How to control NAT IP Hi Antonioss, See the "advertise" option - there is a global one, or a per-socket on: https://www.opensips.org/Documentation/Script-CoreParameters-3-5#advertised_address https://www.opensips.org/Documentation/Script-CoreParameters-3-5#socket (the AS option) Regards, Bogdan-Andrei Iancu OpenSIPS Founder and Developer https://www.opensips-solutions.com https://www.siphub.com On 02.04.2025 15:00, Antonios Psaras wrote: Hello Johan Thank you for your prompt reply. My question is how do I force opensips not to use NAT IP which is defined on socket level? As you mention rtpengine as well, what flags should I pass in order not to use the NAT IP which is also defined as configuration on “external” interface. Thank you once more for your support. Antonis Psaras From: Johan De Clercq <mailto:jo...@democon.be> <jo...@democon.be> Sent: Τετάρτη, 2 Απριλίου 2025 13:23 To: apsa...@microbase.gr <mailto:apsa...@microbase.gr> ; OpenSIPS users mailling list <mailto:users@lists.opensips.org> <users@lists.opensips.org> Subject: Re: [OpenSIPS-Users] mhomed OpenSIPs behind NAT - How to control NAT IP Antonias, yes you can. You need to if then else the stuff. if $si==1.2.34 then use nat else don't use nat. Note, not only for opensips headers, but you will also need different flags for rtpengine. Op wo 2 apr 2025 om 11:35 schreef Antonios Psaras <apsa...@microbase.gr <mailto:apsa...@microbase.gr> >: Dear all. I have the following setup. OpenSIPs Server has two interfaces (DMZ / LAN). DMZ is behind NAT. RTP Engines is also configured. Everything was fine until an end point with in DMZ asked for SIP Trunking. The issue here is that if DMZ Client tries to connect to OpenSIPs DMZ interface, OpenSIPs will reply with NAT IP on SIP body as well as NAT IP on SDP. My thought is to create an other socket on DMZ interface with a different port without NAT configuration and ask the DMZ Client to connect on that interface. That will required extra configuration per peer as I will need to specify the preferred communication socket ie on load balancing configuration. Moreover I should configure a new RTPEngine Service without NAT configuration and route those calls to that one. Most probably the above scenario will work but I am looking for any alternatives to minimize configuration and complexity. Is there any way to control the usage of NAT IP on OpenSIPs script. Ie if source IP is with in DMZ do not send NAT IP in SIP Headers. Regards _______________________________________________ Users mailing list Users@lists.opensips.org <mailto:Users@lists.opensips.org> http://lists.opensips.org/cgi-bin/mailman/listinfo/users _______________________________________________ Users mailing list Users@lists.opensips.org <mailto:Users@lists.opensips.org> http://lists.opensips.org/cgi-bin/mailman/listinfo/users
_______________________________________________ Users mailing list Users@lists.opensips.org http://lists.opensips.org/cgi-bin/mailman/listinfo/users
