Well I built a card to boot, and booted. Looks like I forgot to turn on
capture for the serial console so I did not copy all the firstboot
stuff, but it failed. Video has a few messages displayer, and console a
lot more, but I did not capture that. Console is not accepting any
input; never gets to the login. I can ping the device, so the ethernet
is starting properly; I cannot ssh into the device: 'port 22; connection
refused'.
Perhaps some of the problems come in that you are building a /boot
directory whereas the Cubieboard Fedora builds (19, 20, and pre-alpha
21) all make a separate uboot partition that has all the boot
information and an empty /boot directory in the root partition.
It was a pain to make this card. CP'ing the files I saved back to
firmware required a lot of 'y' to overwrite. there has to be a better
command than cp, but I am not that good to know such things. Even
deleting what was not needed was a bunch of 'rm -fr' commands.
So attached is the console output for 2nd boot. Please advise what to
try next. And perhaps a better way to build the card for testing.
U-Boot SPL 2013.10-rc2-00118-gbf62731 (Oct 13 2013 - 11:53:05)
Board: Cubieboard2
DRAM: 1024 MiB
CPU: 960000000Hz, AXI/AHB/APB: 3/2/2
spl: not an uImage at 1600
U-Boot 2013.10-rc2-00118-gbf62731 (Oct 13 2013 - 11:53:05) Allwinner
Technology
CPU: Allwinner A20 (SUN7I)
Board: Cubieboard2
I2C: ready
DRAM: 1 GiB
MMC: SUNXI SD/MMC: 0
In: serial
Out: serial
Err: serial
Net: emac
Hit any key to stop autoboot: 0
260 bytes read in 6 ms (42 KiB/s)
Loaded environment from uEnv.txt
256 bytes read in 5 ms (49.8 KiB/s)
Jumping to boot.scr
## Executing script at 44000000
45384 bytes read in 11 ms (3.9 MiB/s)
3936816 bytes read in 186 ms (20.2 MiB/s)
## Booting kernel from Legacy Image at 48000000 ...
Image Name: Linux-3.4.61.sun7i+
Created: 2013-10-13 10:11:18 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3936752 Bytes = 3.8 MiB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
[ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7),
cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] Machine: sun7i
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 260096
[ 0.000000] start_kernel(): bug: interrupts were enabled early
[ 0.103359] CPU1: Booted secondary processor
[ 0.343465] highmem bounce pool size: 64 pages
[ 0.352324] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.437188] [NAND] nand driver version: 0x2 0x9
[ 0.493603] Dev Sunxi softw311 nand magic does not match for MBR 1:
��������
[ 0.500704] Dev Sunxi softw311 nand magic does not match for MBR 2:
��������
[ 0.507767] Dev Sunxi softw311 nand magic does not match for MBR 3:
��������
[ 0.514818] Dev Sunxi softw311 nand magic does not match for MBR 4:
��������
[ 0.521877] Dev Sunxi softw311 nand header bad for all MBR copies,
MBR corrupted or not present.
[ 0.530686] Dev Sunxi softw411 nand magic does not match for MBR 1:
��������
[ 0.539562] Dev Sunxi softw411 nand magic does not match for MBR 2:
��������
[ 0.548403] Dev Sunxi softw411 nand magic does not match for MBR 3:
��������
[ 0.557243] Dev Sunxi softw411 nand magic does not match for MBR 4:
��������
[ 0.564313] Dev Sunxi softw411 nand header bad for all MBR copies,
MBR corrupted or not present.
[ 0.573484] [NAND]nand driver, ok.
[ 0.577554] sw_ahci sw_ahci.0: forcing PORTS_IMPL to 0x1
[ 0.596786] emac_init fetch emac using configuration failed
[ 0.603351] [sw-ehci1]: open clock
[ 0.626840] [sw-ehci1]: Set USB Power ON
[ 0.648413] [sw-ohci1]: open clock
[ 0.732344] [sw-ehci2]: open clock
[ 0.755845] [sw-ehci2]: Set USB Power ON
[ 0.778455] [sw-ohci2]: open clock
[ 0.812903] ehci_irq: port change detect
[ 0.863550] sunxi-rtc sunxi-rtc: Error: Set LOSC to external failed.
[ 0.869980] sunxi-rtc sunxi-rtc: Warning: RTC time will be wrong!
[ 0.876656] config i2c gpio with gpio_config api
[ 0.883785] [AXP]axp driver uning configuration failed(340)
[ 0.889396] [AXP]power_start = 0
[ 0.913611] axp20_ldo2: Failed to create debugfs directory
[ 0.923050] [mmc_pm]: failed to fetch sdio card configuration!
[ 0.937735] axp20_buck2: Failed to create debugfs directory
[ 0.983651] disp_clk: Could not find a matching pll-freq for 74600000
pclk
[ 0.990582] disp_clk: Could not find a matching pll-freq for
146850000 pclk
[ 0.997564] disp_clk: Could not find a matching pll-freq for
172900000 pclk
[ 1.004532] disp_clk: Could not find a matching pll-freq for 78800000
pclk
[ 1.011425] disp_clk: Could not find a matching pll-freq for 53450000
pclk
[ 1.018325] disp_clk: Could not find a matching pll-freq for 27100000
pclk
[ 1.025208] disp_clk: Could not find a matching pll-freq for 26150000
pclk
[ 2.519646] [mmc-err] smc 0 err, cmd 52, RTO
[ 2.524889] [mmc-err] smc 0 err, cmd 52, RTO
[ 2.536958] [mmc-err] smc 0 err, cmd 5, RTO
[ 2.552151] [mmc-err] smc 0 err, cmd 5, RTO
[ 2.557280] [mmc-err] smc 0 err, cmd 5, RTO
[ 2.562423] [mmc-err] smc 0 err, cmd 5, RTO
[ 2.867991] axp20_buck3: incomplete constraints, leaving on
[ 2.874255] axp20_buck2: incomplete constraints, leaving on
[ 2.880554] axp20_ldo4: incomplete constraints, leaving on
[ 2.886721] axp20_ldo3: incomplete constraints, leaving on
[ 2.892903] axp20_ldo2: incomplete constraints, leaving on
[ 2.899094] axp20_ldo1: incomplete constraints, leaving on
Welcome to Red Sleeve Enterprise Linux
Starting udev: [ 8.620640] udevd (109): /proc/109/oom_adj is
deprecated, please use /proc/109/oom_score_adj instead.
[ OK ]
Setting hostname redsleeve: [ OK ]
Checking filesystems
Checking all file systems.
[ OK ]
Remounting root filesystem in read-write mode: [ OK ]
Mounting local filesystems: [ OK ]
Enabling /etc/fstab swaps: [ OK ]
Entering non-interactive startup
Bringing up loopback interface: [ OK ]
Starting rpcbind: [ OK ]
Starting system message bus: [ OK ]
Setting network parameters... [ OK ]
Starting NetworkManager daemon: [ OK ]
modem-manager: ModemManager (version 0.4.0-3.git20100628.el6) starting...
modem-manager: Loaded plugin Huawei
Starting NFS statd: modem-manager: Loaded plugin ZTE
modem-manager: Loaded plugin Ericsson MBM
modem-manager: Loaded plugin MotoC
modem-manager: Loaded plugin Gobi
modem-manager: Loaded plugin Option
modem-manager: Loaded plugin Novatel
modem-manager: Loaded plugin Generic
modem-manager: Loaded plugin Longcheer
modem-manager: Loaded plugin Sierra
modem-manager: Loaded plugin AnyData
modem-manager: Loaded plugin Option High-Speed
modem-manager: Loaded plugin SimTech
modem-manager: Loaded plugin Nokia
modem-manager: (tty/ttyS1): port's parent platform driver is not whitelisted
modem-manager: (tty/ttyS2): port's parent platform driver is not whitelisted
modem-manager: (tty/ttyS3): port's parent platform driver is not whitelisted
modem-manager: (tty/ttyS0): port's parent platform driver is not whitelisted
modem-manager: (net/eth0): port's parent platform driver is not whitelisted
[ OK ]
Starting RPC idmapd: [ OK ]
Starting HAL daemon: [ OK ]
Retrigger failed udev events[ OK ]
Starting nscd: [ OK ]
dnsdomainname: Unknown host
Starting dnsmasq: [ OK ]
Starting ntpd: [ OK ]
Starting console mouse services: [ OK ]
_______________________________________________
users mailing list
[email protected]
http://lists.redsleeve.org/mailman/listinfo/users
