On 06/21/06 12:44, Shenen Shenen wrote:
No,this isn't the problem;I've changed the port on my openser like
5070, and asterisk is set like 5060 in sip.conf, but I've always the
same error;
Jun 21 03:33:43 asterisk12 openser[19037]: ERROR: udp_init: bind(6,
0x8119a1c, 16) on 192.168.251.11 <http://192.168.251.11/> <
http://192.168.251.11/>: Cannot assign
requested address
.....what could be?
do you have a network interface configured with the IP 192.168.251.11?
Do 'ifconfig' to check it out.
You can remove the 'listen' parameters from your config file and openser
will bind to available interfaces -- do not forget to set fork=yes,
otherwise openser will listen to the first interface it founds, and that
is usually 127.0.0.1.
Daniel
On 6/21/06, *Daniel-Constantin Mierla* <[EMAIL PROTECTED]
<mailto:[EMAIL PROTECTED]>> wrote:
You can safely ignore reverse resolve DNS messages, they are warnings
meaning no hostname was found set for those IP addresses - openser
tries
to get them in the aliases list. The problem comes from line:
Jun 21 03:33:43 asterisk12 openser[19037]: ERROR: udp_init: bind(6,
0x8119a1c, 16) on 192.168.251.11 <http://192.168.251.11> <
http://192.168.251.11/>: Cannot assign
requested address
This means that you do not have the IP 192.168.251.11
<http://192.168.251.11> configured on the
system. Do you have asterisk and openser listening on the same port
(5060)? You must use different ports.
Cheers,
Daniel
On 06/21/06 10:55, Shenen Shenen wrote:
> Hi!This my openser.cfg;I've 2 asteriskathome with openser
installed;I
> want to copy the authentificated sip registration from one box to
> another and have always the same Sip registered in all 2 box, so if
> one box falls down the other can run without reinitialized all the
> sips (like Phoner..cubix...and also IP phones...)....I'm using
> vrrpd...12 is the master, 11 is the slave, 200 is the virtual
IP(this
> point to the master in the first case..and all Sip proxies like the
> phoner or cubix points to the master..(I can set only 1 proxy..
> 192.168.251.200 <http://192.168.251.200>
<http://192.168.251.200/> ..in x-lite I can set more
> proxies and I'vent problems..)(for this I must use openser..)
>
>
> This is the openser on the "slave" 192.168.251.11
<http://192.168.251.11> <http://192.168.251.11/>
>
>
> # SCRIPT PER COPIARE LO STATO DELLE REGISTRAZIONI DEI SIP DAL
.11 al .12
>
> # ----------- global configuration parameters
------------------------
>
> debug=3 # debug level (cmd line: -dddddddddd)
> fork=no
> log_stderror=no # (cmd line: -E)
> listen= 192.168.251.12 <http://192.168.251.12>
<http://192.168.251.12/>
> listen=192.168.251.11 <http://192.168.251.11> <
http://192.168.251.11/>
> listen=192.1668.251.200
> port=5060
> children=5
> dns=no
> rev_dns=no
> # ------------------ module loading
----------------------------------
>
> loadmodule "modules/mysql/mysql.so"
> loadmodule "modules/sl/sl.so"
> loadmodule "modules/tm/tm.so"
> loadmodule "modules/maxfwd/maxfwd.so"
> loadmodule "modules/usrloc/usrloc.so"
> loadmodule "modules/registrar/registrar.so"
> loadmodule "modules/auth/auth.so"
> loadmodule "modules/auth_db/auth_db.so"
>
> # ----------------- setting module-specific parameters
---------------
>
> # digest generation secret; use the same in backup server;
> # also, make sure that the backup server has sync'ed time
> modparam("auth", "secret", "alsdkhglaksdhfkloiwr")
>
> # ------------------------- request routing logic
-------------------
>
> # main routing logic
>
> route{
>
> # initial sanity checks -- messages with
> # max_forwars==0, or excessively long requests
> if (!mf_process_maxfwd_header("10")) {
> sl_send_reply("483","Too Many Hops");
> return;
> };
> if (len_gt( max_len )) {
> sl_send_reply("513", "Message too big");
> return;
> };
>
> # if the request is for other domain use UsrLoc
> # (in case, it does not work, use the following command
> # with proper names and addresses in it)
> if (uri==myself) {
>
> if (method=="REGISTER") {
>
> # verify credentials
> if (!www_authorize("", "subscriber")) {
> www_challenge("", "0");
> return;
> };
>
> # if ok, update contacts and ...
> save("location");
> # ... if this REGISTER is not a replica from our
> # peer server, replicate to the peer server
> if (!src_ip== 192.168.251.12 <http://192.168.251.12>
<http://192.168.251.12/>) {
> t_replicate("192.168.251.12 <http://192.168.251.12>
<http://192.168.251.12/>", "5060");
> };
> return;
> };
> # do whatever else appropriate for your domain
> log("non-REGISTER\n");
> };
> }
>
>
>
> This is the openser on the "master" 192.168.251.12
<http://192.168.251.12>
> <http://192.168.251.12/ >
>
>
>
>
>
> # SCRIPT PER COPIARE LO STATO DELLE REGISTRAZIONI DEI SIP DAL
.12 al .11
>
> # ----------- global configuration parameters
------------------------
>
> debug=3 # debug level (cmd line: -dddddddddd)
> fork=no
> log_stderror=yes # (cmd line: -E)
> listen= 192.168.251.12 <http://192.168.251.12> <
http://192.168.251.12/>
> listen=192.168.251.11 <http://192.168.251.11>
<http://192.168.251.11/>
> listen=192.1668.251.200
> port=5060
> children=5
> dns=no
> rev_dns=no
>
> # ------------------ module loading
----------------------------------
>
> loadmodule "modules/mysql/mysql.so"
> loadmodule "modules/sl/sl.so"
> loadmodule "modules/tm/tm.so"
> loadmodule "modules/maxfwd/maxfwd.so"
> loadmodule "modules/usrloc/usrloc.so"
> loadmodule "modules/registrar/registrar.so"
> loadmodule "modules/auth/auth.so"
> loadmodule "modules/auth_db/auth_db.so"
>
> # ----------------- setting module-specific parameters
---------------
>
> # digest generation secret; use the same in backup server;
> # also, make sure that the backup server has sync'ed time
> modparam("auth", "secret", "alsdkhglaksdhfkloiwr")
>
> # ------------------------- request routing logic
-------------------
>
> # main routing logic
>
> route{
>
> # initial sanity checks -- messages with
> # max_forwars==0, or excessively long requests
> if (!mf_process_maxfwd_header("10")) {
> sl_send_reply("483","Too Many Hops");
> return;
> };
> if (len_gt( max_len )) {
> sl_send_reply("513", "Message too big");
> return;
> };
>
> # if the request is for other domain use UsrLoc
> # (in case, it does not work, use the following command
> # with proper names and addresses in it)
> if (uri==myself) {
>
> if (method=="REGISTER") {
>
> # verify credentials
> if (!www_authorize("", "subscriber")) {
> www_challenge("", "0");
> return;
> };
>
> # if ok, update contacts and ...
> save("location");
> # ... if this REGISTER is not a replica from our
> # peer server, replicate to the peer server
> if (!src_ip== 192.168.251.11 <http://192.168.251.11>
<http://192.168.251.11/>) {
> t_replicate("192.168.251.11 <http://192.168.251.11>
<http://192.168.251.11/>", "5060");
> };
> return;
> };
> # do whatever else appropriate for your domain
> log("non-REGISTER\n");
> };
> }
>
> If I run the following command... I've problems with resolution
of IP
> addresses... how can I resolve this problem??????????
>
> 100000000000000000000000000000000000000000000000000000
> thanks.....................help me please!!!!!I'm becoming crazy...
>
>
> [EMAIL PROTECTED] ~]# tail -f /var/log/messages
> Jun 21 03:33:43 asterisk12 openser: WARNING: fix_socket_list: could
> not rev. resolve 192.168.251.11 <http://192.168.251.11>
<http://192.168.251.11/>
> Jun 21 03:33:43 asterisk12 openser: WARNING: fix_socket_list: could
> not rev. resolve 192.168.251.200 <http://192.168.251.200>
<http://192.168.251.200/>
> Jun 21 03:33:43 asterisk12 openser[19037]: Maxfwd module-
initializing
> Jun 21 03:33:43 asterisk12 openser[19037]: AUTH module -
initializing
> Jun 21 03:33:43 asterisk12 openser[19037]: AUTH_DB module -
initializing
> Jun 21 03:33:43 asterisk12 openser[19037]: INFO: udp_init:
SO_RCVBUF
> is initially 110592
> Jun 21 03:33:43 asterisk12 openser[19037]: INFO: udp_init: SO_RCVBUF
> is finally 221184
> Jun 21 03:33:43 asterisk12 openser[19037]: INFO: udp_init: SO_RCVBUF
> is initially 110592
> Jun 21 03:33:43 asterisk12 openser[19037]: INFO: udp_init: SO_RCVBUF
> is finally 221184
> Jun 21 03:33:43 asterisk12 openser[19037]: ERROR: udp_init: bind(6,
> 0x8119a1c, 16) on 192.168.251.11 <http://192.168.251.11>
<http://192.168.251.11/>: Cannot
> assign requested address
> Jun 21 03:34:01 asterisk12 crond(pam_unix)[19040]: session
opened for
> user root by (uid=0)
> Jun 21 03:34:01 asterisk12 crond(pam_unix)[19040]: session
closed for
> user root
>
_______________________________________________
Users mailing list
[email protected]
http://openser.org/cgi-bin/mailman/listinfo/users
