The actual operation of creating host is taking time. I believe we've handled its timeout before, but it is possible that our waiting period is still too short.
I will look into this. Veli, could you open a bug please? Thank you. ----- Original Message ----- From: "Itamar Heim" <[email protected]> To: "Eli Mesika" <[email protected]> Cc: "Veli-Matti Leppänen" <[email protected]>, [email protected], "Alex Lourie" <[email protected]> Sent: Sunday, August 19, 2012 7:33:27 PM Subject: Re: [Users] Problems with F17 and ovirt 3.1 On 08/19/2012 12:14 PM, Eli Mesika wrote: > > > ----- Original Message ----- >> From: "Veli-Matti Leppänen" <[email protected]> >> To: [email protected] >> Sent: Sunday, August 19, 2012 11:47:46 AM >> Subject: Re: [Users] Problems with F17 and ovirt 3.1 >> >> >> On 2012-08-19 10:48, Eli Mesika wrote: >>> ----- Original Message ----- >>>> From: "Veli-Matti Leppänen" <[email protected]> >>>> To: [email protected] >>>> Sent: Saturday, August 18, 2012 1:13:23 PM >>>> Subject: Re: [Users] Problems with F17 and ovirt 3.1 >>>> >>>> Hi. >>>> >>>> I tried to install ovirt 3.1 on clean F17 hosts. I tried >>>> all-in-one >>>> and plain manager + node installation, but every time host is just >>>> non-responsive. >>>> >>>> vdsmd service does not start >>>> [root@maila ~]# service vdsmd start >>>> Redirecting to /bin/systemctl start vdsmd.service >>>> Job canceled. >>>> and there is no vdsm log. >>>> >>>> selinux or iptables is not the issue, cause setting selinux to >>>> permissive mode or flushing the firewall does not help. >>>> >>>> any ideas where to start? >>> >>> There was an excellent step-by-step video showing how to install >>> all-in-one on top of f17 >>> please follow and check again >>> >>> http://blog.jebpages.com/archives/up-and-running-with-ovirt-3-1-edition/ >>> >> >> I followed that video. Installation times out during adding local >> host. >> Web admin console shows it installing and after that it goes to >> non-responsing state. > Hi again > please refer to the following (taken from the same site) > > I’ve found that the all-in-one installer sometimes times out during the > install process. If the script times out during the final “AIO: Adding Local > host (This may take several minutes)” step, you can proceed to the web admin > console to complete the process. If it times out at an earlier point, like > waiting for the jboss-as server to start, you should run “engine-cleanup” and > then re-run “engine-setup”. > >> >>>> >>>> /Vellu >>>> >>>> >>>> --- >>>> ______________________ >>>> Veli-Matti Leppänen >>>> [email protected] >>>> Velzi @ IRC >>>> >>>> _______________________________________________ >>>> Users mailing list >>>> [email protected] >>>> http://lists.ovirt.org/mailman/listinfo/users >>>> >> >> _______________________________________________ >> Users mailing list >> [email protected] >> http://lists.ovirt.org/mailman/listinfo/users >> > _______________________________________________ > Users mailing list > [email protected] > http://lists.ovirt.org/mailman/listinfo/users > Eli/Alex - what are we timing out on? 1. all-in-one rpm is supposed to require vdsm rpms so the add host wouldn't really need to install them 2. all-in-one is skipping the reboot _______________________________________________ Users mailing list [email protected] http://lists.ovirt.org/mailman/listinfo/users
