Hello,
I have a newly created datacenter in 3.2.1 with f18 host where
ovirtmgmt is set as vlan.
host is installed but after some minutes I get this messages:
Host management02 moved to Non-Operational state because interfaces
'em1.311' are down but are needed by networks 'ovirtmgmt' in the
current cluster
from an operating system point of view it seems that all is ok on the host
[root@management02 ~]# ip addr list
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
2: em1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 00:15:17:b4:99:3c brd ff:ff:ff:ff:ff:ff
3: em2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 00:15:17:b4:99:3d brd ff:ff:ff:ff:ff:ff
inet 213.205.41.202/26 brd 213.205.41.255 scope global em2
4: em1.311@em1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc
noqueue master ovirtmgmt state UP
link/ether 00:15:17:b4:99:3c brd ff:ff:ff:ff:ff:ff
5: ovirtmgmt: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP
link/ether 00:15:17:b4:99:3c brd ff:ff:ff:ff:ff:ff
inet 10.39.71.12/26 brd 10.39.71.63 scope global ovirtmgmt
7: ;vdsmdummy;: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
link/ether 36:98:c3:39:5f:43 brd ff:ff:ff:ff:ff:ff
8: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
9: bond4: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
10: bond1: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
11: bond2: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
12: bond3: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
[root@management02 ~]# ethtool em1
Settings for em1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
[root@management02 ~]# ethtool em1.311
Settings for em1.311:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Link detected: yes
On engine
[root@management01 ~]# ip addr list
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
2: em1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 00:15:17:b1:1f:e8 brd ff:ff:ff:ff:ff:ff
3: em2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 00:15:17:b1:1f:e9 brd ff:ff:ff:ff:ff:ff
inet 213.205.41.201/26 brd 213.205.41.255 scope global em2
4: em1.192@em1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc
noqueue state UP
link/ether 00:15:17:b1:1f:e8 brd ff:ff:ff:ff:ff:ff
inet 192.168.230.1/24 brd 192.168.230.255 scope global em1.192
5: em1.311@em1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc
noqueue state UP
link/ether 00:15:17:b1:1f:e8 brd ff:ff:ff:ff:ff:ff
inet 10.39.71.11/26 brd 10.39.71.63 scope global em1.311
[root@management01 ~]# ethtool em1
Settings for em1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
[root@management01 ~]# ethtool em1.311
Settings for em1.311:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Link detected: yes
what can be the cause?
what is the check that runs and move the host to non-operational?
Thanks
Gianluca
_______________________________________________
Users mailing list
[email protected]
http://lists.ovirt.org/mailman/listinfo/users
