Hi Juan, Refer to this post, the state of affairs didn't chagne since then: http://lists.ovirt.org/pipermail/users/2013-May/014429.html
David On Po, 2014-11-24 at 11:48 +0100, Juan Jose wrote: > Hello Lev and Michal and everybody, > > > My main question is: > > Is it necessary to install in Windows 7 client, no in the guest, the > usbclerk to be able to get USB pen drive into the VM from the Windows > 7 client?, in afirmative case, where can I get usbclerk? > > > Many thanks in advanced, > > > Juanjo. > > > On Sun, Nov 23, 2014 at 9:42 AM, Lev Veyde <[email protected]> wrote: > Hi Michal, > > As far as I know there is no need to install something inside > VM for the Native USB redirection to function properly, thus > nothing related is included on the oVirt WGT ISO. > > The user/admin only needs to properly configure the VM for > Native USB redirection and install the Spice client. > > I forwarded the issue to the Spice team, they could properly > point to the issue. > > Thanks in advance, > Lev Veyde. > > ----- Original Message ----- > From: "Michal Skrivanek" <[email protected]> > To: "Juan Jose" <[email protected]>, "Lev Veyde" > <[email protected]> > Cc: "[email protected] List" <[email protected]> > Sent: Friday, November 21, 2014 3:07:09 PM > Subject: Re: [ovirt-users] USB redirect > > > On Nov 13, 2014, at 12:00 , Juan Jose <[email protected]> > wrote: > > > Hello Michal and everybody, > > > > I'm sorry but I have downloaded ovirt-guest-tools from URL > you gave me but the driver usbredir is not there. Is it normal > or maybe it is in another resource? > > > > As the oVirt documentation says, when this driver is > installed a new USB windows service will be started in the > client, but after execute the ovirt-guest-tool setup and > finish the installation there is not any USB new service in my > Windows client. > > > > Is it possible that this usbredir driver is not in this ISO? > > adding Lev who builds the ISO…can you please check? > > Thanks, > michal > > > > > Many thanks in advanced, > > > > Juanjo. > > > > On Wed, Nov 12, 2014 at 4:55 PM, Juan Jose > <[email protected]> wrote: > > Many thanks Michal, > > > > I will try it and I will try to upgrade my oVirt 3.4. > > > > Thanks again and best regards, > > > > Juanjo. > > > > On Wed, Nov 12, 2014 at 4:45 PM, Michal Skrivanek > <[email protected]> wrote: > > > > On Nov 12, 2014, at 16:39 , Juan Jose <[email protected]> > wrote: > > > > > Hello Michal or everybody, > > > > > > Could you tell me where can I get or download > ovirt-guest-tool.iso? > > > > Hi, > > it's a regular part of the 3.5 release... > > > http://resources.ovirt.org/pub/ovirt-3.5/iso/ovirt-guest-tools/ > > enjoy!:) > > > > Thanks, > > michal > > > > > > > > Many thanks in advanced, > > > > > > Juanjo. > > > > > > > > > On Tue, Nov 11, 2014 at 12:15 PM, Michal Skrivanek > <[email protected]> wrote: > > > > > > On Nov 11, 2014, at 11:08 , Juan Jose <[email protected]> > wrote: > > > > > > > Thank you very much Michal, If I have checked Device > administrator in my Windows 7 VM and as you can see in the > attached image, the USB device is correctly installed. But > when I click "File" in remote-viewer "USB device selection" > appears in grey and I can't select any USB device. > > > > > > > > Is there any other requirement to be able redirect USB > devices?, Is it necessary to install usbclerk in Windows > clients to redirect USB to the Windows guest? > > > > > > usbredir drivers yes, you need them, they should be on the > guest tools iso > > > > > > Thanks, > > > michal > > > > > > > > > > > Many thanks in advanced, > > > > > > > > Juanjo. > > > > > > > > On Tue, Nov 11, 2014 at 8:23 AM, Michal Skrivanek > <[email protected]> wrote: > > > > > > > > On Nov 10, 2014, at 17:54 , Juan Jose > <[email protected]> wrote: > > > > > > > > > Hello everybody, > > > > > > > > > > I have an oVirt 3.4 deployment and I have some > Windows 7 Enterprise 32 bits guests. I can't redirect USB from > a Windows 7 client. I'm using remote - viewer as console. Also > I have observed something wrong in my administration portal. > The oVirt documentation says that I have to select Native USB > mode in console properties in VM configuration > > > > > > > > yes, that's the only supported way > > > > you should see the USB controller in devices > > > > > > > > > but after select this mode, it doesn't remain. If I > check this value in console configuration again I can see > disabled, native mode value have been changed. > > > > > > > > there used to be such issue in 3.4..it is fixed in 3.5 > already. > > > > It should be a UI problem only… > > > > > > > > Thanks, > > > > michal > > > > > > > > > > > > > > Is there someone have had this problem?, and how I can > solve it?, is it necessary to install in Windows clients us > clerk software? > > > > > > > > > > Many thanks in advanced. > > > > > > > > > > Juanjo. > > > > > _______________________________________________ > > > > > Users mailing list > > > > > [email protected] > > > > > http://lists.ovirt.org/mailman/listinfo/users > > > > > > > > > > > > <DeviceAdministrator.png> > > > > > > > > > > > > > > > > > _______________________________________________ > Users mailing list > [email protected] > http://lists.ovirt.org/mailman/listinfo/users _______________________________________________ Users mailing list [email protected] http://lists.ovirt.org/mailman/listinfo/users
