Unfortunately, I can't check on the switch. Trust me, I've tried.
These servers are in a Co-Lo and I've put 5 tickets in asking about
the port configuration. They just get ignored - but that's par for the
coarse for IT here. Only about 2 out of 10 of our tickets get any
response and usually the response doesn't help. Then the system they
use auto-closes the ticket. That was why I was suspecting STP before.

I can do ethtool. I do have root on these servers, though. Are you
trying to get me to turn off link-speed auto-negotiation? Would you
like me to try that?

On Fri, Aug 23, 2019 at 12:24 PM Dominik Holler <dhol...@redhat.com> wrote:
>
>
>
> On Fri, Aug 23, 2019 at 5:49 PM Curtis E. Combs Jr. <ej.alb...@gmail.com> 
> wrote:
>>
>> Sure! Right now, I only have a 500gb partition on each node shared over NFS, 
>> added as storage domains. This is on each node - so, currently 3.
>>
>> How can the storage cause a node to drop out?
>>
>
> Thanks, I got it.
> All three links go down on load, which causes NFS to fail.
>
> Can you check in the switch port configuration if there is some kind of 
> Ethernet flow control enabled?
> Can you try to modify the behavior by changing the settings of your host 
> interfaces, e.g.
>
> ethtool -A em1 autoneg off rx off tx off
>
> or
> ethtool -A em1 autoneg on rx on tx on
> ?
>
>
>
>
>>
>> On Fri, Aug 23, 2019, 11:46 AM Dominik Holler <dhol...@redhat.com> wrote:
>>>
>>>
>>>
>>> On Fri, Aug 23, 2019 at 5:41 PM Curtis E. Combs Jr. <ej.alb...@gmail.com> 
>>> wrote:
>>>>
>>>> Also, if it helps, the hosts will sit there, quietly, for hours or
>>>> days before anything happens. They're up and working just fine. But
>>>> then, when I manually migrate a VM from one host to another, they
>>>> become completely inaccessible.
>>>>
>>>
>>> Can you share some details about your storage?
>>> Maybe there is a feature used during live migration, which triggers the 
>>> issue.
>>>
>>>
>>>>
>>>> These are vanilla-as-possible CentOS7 nodes. Very basic ovirt install
>>>> and configuration.
>>>>
>>>> On Fri, Aug 23, 2019 at 11:33 AM Curtis E. Combs Jr.
>>>> <ej.alb...@gmail.com> wrote:
>>>> >
>>>> > Hey Dominik,
>>>> >
>>>> > Thanks for helping. I really want to try to use ovirt.
>>>> >
>>>> > When these events happen, I cannot even SSH to the nodes due to the
>>>> > link being down. After a little while, the hosts come back...
>>>> >
>>>> > On Fri, Aug 23, 2019 at 11:30 AM Dominik Holler <dhol...@redhat.com> 
>>>> > wrote:
>>>> > >
>>>> > > Is you storage connected via NFS?
>>>> > > Can you manually access the storage on the host?
>>>> > >
>>>> > >
>>>> > > On Fri, Aug 23, 2019 at 5:19 PM Curtis E. Combs Jr. 
>>>> > > <ej.alb...@gmail.com> wrote:
>>>> > >>
>>>> > >> Sorry to dead bump this, but I'm beginning to suspect that maybe it's
>>>> > >> not STP that's the problem.
>>>> > >>
>>>> > >> 2 of my hosts just went down when a few VMs tried to migrate.
>>>> > >>
>>>> > >> Do any of you have any idea what might be going on here? I don't even
>>>> > >> know where to start. I'm going to include the dmesg in case it helps.
>>>> > >> This happens on both of the hosts whenever any migration attempts to 
>>>> > >> start.
>>>> > >>
>>>> > >>
>>>> > >>
>>>> > >>
>>>> > >>
>>>> > >>
>>>> > >>
>>>> > >>
>>>> > >>
>>>> > >> [68099.245833] bnx2 0000:01:00.0 em1: NIC Copper Link is Down
>>>> > >> [68099.246055] internal: port 1(em1) entered disabled state
>>>> > >> [68184.177343] ixgbe 0000:03:00.0 p1p1: NIC Link is Down
>>>> > >> [68184.177789] ovirtmgmt: port 1(p1p1) entered disabled state
>>>> > >> [68184.177856] ovirtmgmt: topology change detected, propagating
>>>> > >> [68277.078671] INFO: task qemu-kvm:8888 blocked for more than 120 
>>>> > >> seconds.
>>>> > >> [68277.078700] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs"
>>>> > >> disables this message.
>>>> > >> [68277.078723] qemu-kvm        D ffff9db40c359040     0  8888      1 
>>>> > >> 0x000001a0
>>>> > >> [68277.078727] Call Trace:
>>>> > >> [68277.078738]  [<ffffffff978fd2ac>] ? avc_has_perm_flags+0xdc/0x1c0
>>>> > >> [68277.078743]  [<ffffffff97d69f19>] schedule+0x29/0x70
>>>> > >> [68277.078746]  [<ffffffff9785f3d9>] inode_dio_wait+0xd9/0x100
>>>> > >> [68277.078751]  [<ffffffff976c4010>] ? wake_bit_function+0x40/0x40
>>>> > >> [68277.078765]  [<ffffffffc09d6dd6>] nfs_getattr+0x1b6/0x250 [nfs]
>>>> > >> [68277.078768]  [<ffffffff97848109>] vfs_getattr+0x49/0x80
>>>> > >> [68277.078769]  [<ffffffff97848185>] vfs_fstat+0x45/0x80
>>>> > >> [68277.078771]  [<ffffffff978486f4>] SYSC_newfstat+0x24/0x60
>>>> > >> [68277.078774]  [<ffffffff97d76d21>] ? 
>>>> > >> system_call_after_swapgs+0xae/0x146
>>>> > >> [68277.078778]  [<ffffffff97739f34>] ? 
>>>> > >> __audit_syscall_entry+0xb4/0x110
>>>> > >> [68277.078782]  [<ffffffff9763aaeb>] ? syscall_trace_enter+0x16b/0x220
>>>> > >> [68277.078784]  [<ffffffff97848ace>] SyS_newfstat+0xe/0x10
>>>> > >> [68277.078786]  [<ffffffff97d7706b>] tracesys+0xa3/0xc9
>>>> > >> [68397.072384] INFO: task qemu-kvm:8888 blocked for more than 120 
>>>> > >> seconds.
>>>> > >> [68397.072413] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs"
>>>> > >> disables this message.
>>>> > >> [68397.072436] qemu-kvm        D ffff9db40c359040     0  8888      1 
>>>> > >> 0x000001a0
>>>> > >> [68397.072439] Call Trace:
>>>> > >> [68397.072453]  [<ffffffff978fd2ac>] ? avc_has_perm_flags+0xdc/0x1c0
>>>> > >> [68397.072458]  [<ffffffff97d69f19>] schedule+0x29/0x70
>>>> > >> [68397.072462]  [<ffffffff9785f3d9>] inode_dio_wait+0xd9/0x100
>>>> > >> [68397.072467]  [<ffffffff976c4010>] ? wake_bit_function+0x40/0x40
>>>> > >> [68397.072480]  [<ffffffffc09d6dd6>] nfs_getattr+0x1b6/0x250 [nfs]
>>>> > >> [68397.072485]  [<ffffffff97848109>] vfs_getattr+0x49/0x80
>>>> > >> [68397.072486]  [<ffffffff97848185>] vfs_fstat+0x45/0x80
>>>> > >> [68397.072488]  [<ffffffff978486f4>] SYSC_newfstat+0x24/0x60
>>>> > >> [68397.072491]  [<ffffffff97d76d21>] ? 
>>>> > >> system_call_after_swapgs+0xae/0x146
>>>> > >> [68397.072495]  [<ffffffff97739f34>] ? 
>>>> > >> __audit_syscall_entry+0xb4/0x110
>>>> > >> [68397.072498]  [<ffffffff9763aaeb>] ? syscall_trace_enter+0x16b/0x220
>>>> > >> [68397.072500]  [<ffffffff97848ace>] SyS_newfstat+0xe/0x10
>>>> > >> [68397.072502]  [<ffffffff97d7706b>] tracesys+0xa3/0xc9
>>>> > >> [68401.573141] bnx2 0000:01:00.0 em1: NIC Copper Link is Up, 1000 Mbps
>>>> > >> full duplex
>>>> > >>
>>>> > >> [68401.573247] internal: port 1(em1) entered blocking state
>>>> > >> [68401.573255] internal: port 1(em1) entered listening state
>>>> > >> [68403.576985] internal: port 1(em1) entered learning state
>>>> > >> [68405.580907] internal: port 1(em1) entered forwarding state
>>>> > >> [68405.580916] internal: topology change detected, propagating
>>>> > >> [68469.565589] nfs: server swm-01.hpc.moffitt.org not responding, 
>>>> > >> timed out
>>>> > >> [68469.565840] nfs: server swm-01.hpc.moffitt.org not responding, 
>>>> > >> timed out
>>>> > >> [68487.193932] ixgbe 0000:03:00.0 p1p1: NIC Link is Up 10 Gbps, Flow
>>>> > >> Control: RX/TX
>>>> > >> [68487.194105] ovirtmgmt: port 1(p1p1) entered blocking state
>>>> > >> [68487.194114] ovirtmgmt: port 1(p1p1) entered listening state
>>>> > >> [68489.196508] ovirtmgmt: port 1(p1p1) entered learning state
>>>> > >> [68491.200400] ovirtmgmt: port 1(p1p1) entered forwarding state
>>>> > >> [68491.200405] ovirtmgmt: topology change detected, sending tcn bpdu
>>>> > >> [68493.672423] NFS: nfs4_reclaim_open_state: Lock reclaim failed!
>>>> > >> [68494.777996] NFSD: client 10.15.28.22 testing state ID with
>>>> > >> incorrect client ID
>>>> > >> [68494.778580] NFSD: client 10.15.28.22 testing state ID with
>>>> > >> incorrect client ID
>>>> > >>
>>>> > >>
>>>> > >> On Thu, Aug 22, 2019 at 2:53 PM Curtis E. Combs Jr. 
>>>> > >> <ej.alb...@gmail.com> wrote:
>>>> > >> >
>>>> > >> > Thanks, I'm just going to revert back to bridges.
>>>> > >> >
>>>> > >> > On Thu, Aug 22, 2019 at 11:50 AM Dominik Holler 
>>>> > >> > <dhol...@redhat.com> wrote:
>>>> > >> > >
>>>> > >> > >
>>>> > >> > >
>>>> > >> > > On Thu, Aug 22, 2019 at 3:06 PM Curtis E. Combs Jr. 
>>>> > >> > > <ej.alb...@gmail.com> wrote:
>>>> > >> > >>
>>>> > >> > >> Seems like the STP options are so common and necessary that it 
>>>> > >> > >> would
>>>> > >> > >> be a priority over seldom-used bridge_opts. I know what STP is 
>>>> > >> > >> and I'm
>>>> > >> > >> not even a networking guy - never even heard of half of the
>>>> > >> > >> bridge_opts that have switches in the UI.
>>>> > >> > >>
>>>> > >> > >> Anyway. I wanted to try the openvswitches, so I reinstalled all 
>>>> > >> > >> of my
>>>> > >> > >> nodes and used "openvswitch (Technology Preview)" as the 
>>>> > >> > >> engine-setup
>>>> > >> > >> option for the first host. I made a new Cluster for my nodes, 
>>>> > >> > >> added
>>>> > >> > >> them all to the new cluster, created a new "logical network" for 
>>>> > >> > >> the
>>>> > >> > >> internal network and attached it to the internal network ports.
>>>> > >> > >>
>>>> > >> > >> Now, when I go to create a new VM, I don't even have either the
>>>> > >> > >> ovirtmgmt switch OR the internal switch as an option. The 
>>>> > >> > >> drop-down is
>>>> > >> > >> empy as if I don't have any vnic-profiles.
>>>> > >> > >>
>>>> > >> > >
>>>> > >> > > openvswitch clusters are limited to ovn networks.
>>>> > >> > > You can create one like described in
>>>> > >> > > https://www.ovirt.org/documentation/admin-guide/chap-External_Providers.html#connecting-an-ovn-network-to-a-physical-network
>>>> > >> > >
>>>> > >> > >
>>>> > >> > >>
>>>> > >> > >> On Thu, Aug 22, 2019 at 7:34 AM Tony Pearce <tony...@gmail.com> 
>>>> > >> > >> wrote:
>>>> > >> > >> >
>>>> > >> > >> > Hi Dominik, would you mind sharing the use case for stp via 
>>>> > >> > >> > API Only? I am keen to know this.
>>>> > >> > >> > Thanks
>>>> > >> > >> >
>>>> > >> > >> >
>>>> > >> > >> > On Thu., 22 Aug. 2019, 19:24 Dominik Holler, 
>>>> > >> > >> > <dhol...@redhat.com> wrote:
>>>> > >> > >> >>
>>>> > >> > >> >>
>>>> > >> > >> >>
>>>> > >> > >> >> On Thu, Aug 22, 2019 at 1:08 PM Miguel Duarte de Mora Barroso 
>>>> > >> > >> >> <mdbarr...@redhat.com> wrote:
>>>> > >> > >> >>>
>>>> > >> > >> >>> On Sat, Aug 17, 2019 at 11:27 AM <ej.alb...@gmail.com> wrote:
>>>> > >> > >> >>> >
>>>> > >> > >> >>> > Hello. I have been trying to figure out an issue for a 
>>>> > >> > >> >>> > very long time.
>>>> > >> > >> >>> > That issue relates to the ethernet and 10gb fc links that 
>>>> > >> > >> >>> > I have on my
>>>> > >> > >> >>> > cluster being disabled any time a migration occurs.
>>>> > >> > >> >>> >
>>>> > >> > >> >>> > I believe this is because I need to have STP turned on in 
>>>> > >> > >> >>> > order to
>>>> > >> > >> >>> > participate with the switch. However, there does not seem 
>>>> > >> > >> >>> > to be any
>>>> > >> > >> >>> > way to tell oVirt to stop turning it off! Very frustrating.
>>>> > >> > >> >>> >
>>>> > >> > >> >>> > After entering a cronjob that enables stp on all bridges 
>>>> > >> > >> >>> > every 1
>>>> > >> > >> >>> > minute, the migration issue disappears....
>>>> > >> > >> >>> >
>>>> > >> > >> >>> > Is there any way at all to do without this cronjob and set 
>>>> > >> > >> >>> > STP to be
>>>> > >> > >> >>> > ON without having to resort to such a silly solution?
>>>> > >> > >> >>>
>>>> > >> > >> >>> Vdsm exposes a per bridge STP knob that you can use for 
>>>> > >> > >> >>> this. By
>>>> > >> > >> >>> default it is set to false, which is probably why you had to 
>>>> > >> > >> >>> use this
>>>> > >> > >> >>> shenanigan.
>>>> > >> > >> >>>
>>>> > >> > >> >>> You can, for instance:
>>>> > >> > >> >>>
>>>> > >> > >> >>> # show present state
>>>> > >> > >> >>> [vagrant@vdsm ~]$ ip a
>>>> > >> > >> >>> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state 
>>>> > >> > >> >>> UNKNOWN
>>>> > >> > >> >>> group default qlen 1000
>>>> > >> > >> >>>     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
>>>> > >> > >> >>>     inet 127.0.0.1/8 scope host lo
>>>> > >> > >> >>>        valid_lft forever preferred_lft forever
>>>> > >> > >> >>> 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc 
>>>> > >> > >> >>> pfifo_fast
>>>> > >> > >> >>> state UP group default qlen 1000
>>>> > >> > >> >>>     link/ether 52:54:00:41:fb:37 brd ff:ff:ff:ff:ff:ff
>>>> > >> > >> >>> 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc 
>>>> > >> > >> >>> pfifo_fast
>>>> > >> > >> >>> state UP group default qlen 1000
>>>> > >> > >> >>>     link/ether 52:54:00:83:5b:6f brd ff:ff:ff:ff:ff:ff
>>>> > >> > >> >>>     inet 192.168.50.50/24 brd 192.168.50.255 scope global 
>>>> > >> > >> >>> noprefixroute eth1
>>>> > >> > >> >>>        valid_lft forever preferred_lft forever
>>>> > >> > >> >>>     inet6 fe80::5054:ff:fe83:5b6f/64 scope link
>>>> > >> > >> >>>        valid_lft forever preferred_lft forever
>>>> > >> > >> >>> 19: ;vdsmdummy;: <BROADCAST,MULTICAST> mtu 1500 qdisc noop 
>>>> > >> > >> >>> state DOWN
>>>> > >> > >> >>> group default qlen 1000
>>>> > >> > >> >>>     link/ether 8e:5c:2e:87:fa:0b brd ff:ff:ff:ff:ff:ff
>>>> > >> > >> >>>
>>>> > >> > >> >>> # show example bridge configuration - you're looking for the 
>>>> > >> > >> >>> STP knob here.
>>>> > >> > >> >>> [root@vdsm ~]$ cat bridged_net_with_stp
>>>> > >> > >> >>> {
>>>> > >> > >> >>>   "bondings": {},
>>>> > >> > >> >>>   "networks": {
>>>> > >> > >> >>>     "test-network": {
>>>> > >> > >> >>>       "nic": "eth0",
>>>> > >> > >> >>>       "switch": "legacy",
>>>> > >> > >> >>>       "bridged": true,
>>>> > >> > >> >>>       "stp": true
>>>> > >> > >> >>>     }
>>>> > >> > >> >>>   },
>>>> > >> > >> >>>   "options": {
>>>> > >> > >> >>>     "connectivityCheck": false
>>>> > >> > >> >>>   }
>>>> > >> > >> >>> }
>>>> > >> > >> >>>
>>>> > >> > >> >>> # issue setup networks command:
>>>> > >> > >> >>> [root@vdsm ~]$ vdsm-client -f bridged_net_with_stp Host 
>>>> > >> > >> >>> setupNetworks
>>>> > >> > >> >>> {
>>>> > >> > >> >>>     "code": 0,
>>>> > >> > >> >>>     "message": "Done"
>>>> > >> > >> >>> }
>>>> > >> > >> >>>
>>>> > >> > >> >>> # show bridges
>>>> > >> > >> >>> [root@vdsm ~]$ brctl show
>>>> > >> > >> >>> bridge name bridge id STP enabled interfaces
>>>> > >> > >> >>> ;vdsmdummy; 8000.000000000000 no
>>>> > >> > >> >>> test-network 8000.52540041fb37 yes eth0
>>>> > >> > >> >>>
>>>> > >> > >> >>> # show final state
>>>> > >> > >> >>> [root@vdsm ~]$ ip a
>>>> > >> > >> >>> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state 
>>>> > >> > >> >>> UNKNOWN
>>>> > >> > >> >>> group default qlen 1000
>>>> > >> > >> >>>     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
>>>> > >> > >> >>>     inet 127.0.0.1/8 scope host lo
>>>> > >> > >> >>>        valid_lft forever preferred_lft forever
>>>> > >> > >> >>> 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc 
>>>> > >> > >> >>> pfifo_fast
>>>> > >> > >> >>> master test-network state UP group default qlen 1000
>>>> > >> > >> >>>     link/ether 52:54:00:41:fb:37 brd ff:ff:ff:ff:ff:ff
>>>> > >> > >> >>> 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc 
>>>> > >> > >> >>> pfifo_fast
>>>> > >> > >> >>> state UP group default qlen 1000
>>>> > >> > >> >>>     link/ether 52:54:00:83:5b:6f brd ff:ff:ff:ff:ff:ff
>>>> > >> > >> >>>     inet 192.168.50.50/24 brd 192.168.50.255 scope global 
>>>> > >> > >> >>> noprefixroute eth1
>>>> > >> > >> >>>        valid_lft forever preferred_lft forever
>>>> > >> > >> >>>     inet6 fe80::5054:ff:fe83:5b6f/64 scope link
>>>> > >> > >> >>>        valid_lft forever preferred_lft forever
>>>> > >> > >> >>> 19: ;vdsmdummy;: <BROADCAST,MULTICAST> mtu 1500 qdisc noop 
>>>> > >> > >> >>> state DOWN
>>>> > >> > >> >>> group default qlen 1000
>>>> > >> > >> >>>     link/ether 8e:5c:2e:87:fa:0b brd ff:ff:ff:ff:ff:ff
>>>> > >> > >> >>> 432: test-network: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 
>>>> > >> > >> >>> 1500 qdisc
>>>> > >> > >> >>> noqueue state UP group default qlen 1000
>>>> > >> > >> >>>     link/ether 52:54:00:41:fb:37 brd ff:ff:ff:ff:ff:ff
>>>> > >> > >> >>>
>>>> > >> > >> >>> I don't think this STP parameter is exposed via engine UI; 
>>>> > >> > >> >>> @Dominik
>>>> > >> > >> >>> Holler , could you confirm ? What are our plans for it ?
>>>> > >> > >> >>>
>>>> > >> > >> >>
>>>> > >> > >> >> STP is only available via REST-API, see
>>>> > >> > >> >> http://ovirt.github.io/ovirt-engine-api-model/4.3/#types/network
>>>> > >> > >> >> please find an example how to enable STP in
>>>> > >> > >> >> https://gist.github.com/dominikholler/4e70c9ef9929d93b6807f56d43a70b95
>>>> > >> > >> >>
>>>> > >> > >> >> We have no plans to add STP to the web ui,
>>>> > >> > >> >> but new feature requests are always welcome on
>>>> > >> > >> >> https://bugzilla.redhat.com/enter_bug.cgi?product=ovirt-engine
>>>> > >> > >> >>
>>>> > >> > >> >>
>>>> > >> > >> >>>
>>>> > >> > >> >>> >
>>>> > >> > >> >>> > Here are some details about my systems, if you need it.
>>>> > >> > >> >>> >
>>>> > >> > >> >>> >
>>>> > >> > >> >>> > selinux is disabled.
>>>> > >> > >> >>> >
>>>> > >> > >> >>> >
>>>> > >> > >> >>> >
>>>> > >> > >> >>> >
>>>> > >> > >> >>> >
>>>> > >> > >> >>> >
>>>> > >> > >> >>> >
>>>> > >> > >> >>> >
>>>> > >> > >> >>> >
>>>> > >> > >> >>> > [root@swm-02 ~]# rpm -qa | grep ovirt
>>>> > >> > >> >>> > ovirt-imageio-common-1.5.1-0.el7.x86_64
>>>> > >> > >> >>> > ovirt-release43-4.3.5.2-1.el7.noarch
>>>> > >> > >> >>> > ovirt-imageio-daemon-1.5.1-0.el7.noarch
>>>> > >> > >> >>> > ovirt-vmconsole-host-1.0.7-2.el7.noarch
>>>> > >> > >> >>> > ovirt-hosted-engine-setup-2.3.11-1.el7.noarch
>>>> > >> > >> >>> > ovirt-ansible-hosted-engine-setup-1.0.26-1.el7.noarch
>>>> > >> > >> >>> > python2-ovirt-host-deploy-1.8.0-1.el7.noarch
>>>> > >> > >> >>> > ovirt-ansible-engine-setup-1.1.9-1.el7.noarch
>>>> > >> > >> >>> > python2-ovirt-setup-lib-1.2.0-1.el7.noarch
>>>> > >> > >> >>> > cockpit-machines-ovirt-195.1-1.el7.noarch
>>>> > >> > >> >>> > ovirt-hosted-engine-ha-2.3.3-1.el7.noarch
>>>> > >> > >> >>> > ovirt-vmconsole-1.0.7-2.el7.noarch
>>>> > >> > >> >>> > cockpit-ovirt-dashboard-0.13.5-1.el7.noarch
>>>> > >> > >> >>> > ovirt-provider-ovn-driver-1.2.22-1.el7.noarch
>>>> > >> > >> >>> > ovirt-host-deploy-common-1.8.0-1.el7.noarch
>>>> > >> > >> >>> > ovirt-host-4.3.4-1.el7.x86_64
>>>> > >> > >> >>> > python-ovirt-engine-sdk4-4.3.2-2.el7.x86_64
>>>> > >> > >> >>> > ovirt-host-dependencies-4.3.4-1.el7.x86_64
>>>> > >> > >> >>> > ovirt-ansible-repositories-1.1.5-1.el7.noarch
>>>> > >> > >> >>> > [root@swm-02 ~]# cat /etc/redhat-release
>>>> > >> > >> >>> > CentOS Linux release 7.6.1810 (Core)
>>>> > >> > >> >>> > [root@swm-02 ~]# uname -r
>>>> > >> > >> >>> > 3.10.0-957.27.2.el7.x86_64
>>>> > >> > >> >>> > You have new mail in /var/spool/mail/root
>>>> > >> > >> >>> > [root@swm-02 ~]# ip a
>>>> > >> > >> >>> > 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue 
>>>> > >> > >> >>> > state UNKNOWN
>>>> > >> > >> >>> > group default qlen 1000
>>>> > >> > >> >>> >     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
>>>> > >> > >> >>> >     inet 127.0.0.1/8 scope host lo
>>>> > >> > >> >>> >        valid_lft forever preferred_lft forever
>>>> > >> > >> >>> > 2: em1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc 
>>>> > >> > >> >>> > mq master
>>>> > >> > >> >>> > test state UP group default qlen 1000
>>>> > >> > >> >>> >     link/ether d4:ae:52:8d:50:48 brd ff:ff:ff:ff:ff:ff
>>>> > >> > >> >>> > 3: em2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state 
>>>> > >> > >> >>> > DOWN group
>>>> > >> > >> >>> > default qlen 1000
>>>> > >> > >> >>> >     link/ether d4:ae:52:8d:50:49 brd ff:ff:ff:ff:ff:ff
>>>> > >> > >> >>> > 4: p1p1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc 
>>>> > >> > >> >>> > mq master
>>>> > >> > >> >>> > ovirtmgmt state UP group default qlen 1000
>>>> > >> > >> >>> >     link/ether 90:e2:ba:1e:14:80 brd ff:ff:ff:ff:ff:ff
>>>> > >> > >> >>> > 5: p1p2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state 
>>>> > >> > >> >>> > DOWN group
>>>> > >> > >> >>> > default qlen 1000
>>>> > >> > >> >>> >     link/ether 90:e2:ba:1e:14:81 brd ff:ff:ff:ff:ff:ff
>>>> > >> > >> >>> > 6: ovs-system: <BROADCAST,MULTICAST> mtu 1500 qdisc noop 
>>>> > >> > >> >>> > state DOWN
>>>> > >> > >> >>> > group default qlen 1000
>>>> > >> > >> >>> >     link/ether a2:b8:d6:e8:b3:d8 brd ff:ff:ff:ff:ff:ff
>>>> > >> > >> >>> > 7: br-int: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state 
>>>> > >> > >> >>> > DOWN group
>>>> > >> > >> >>> > default qlen 1000
>>>> > >> > >> >>> >     link/ether 96:a0:c1:4a:45:4b brd ff:ff:ff:ff:ff:ff
>>>> > >> > >> >>> > 25: test: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc 
>>>> > >> > >> >>> > noqueue
>>>> > >> > >> >>> > state UP group default qlen 1000
>>>> > >> > >> >>> >     link/ether d4:ae:52:8d:50:48 brd ff:ff:ff:ff:ff:ff
>>>> > >> > >> >>> >     inet 10.15.11.21/24 brd 10.15.11.255 scope global test
>>>> > >> > >> >>> >        valid_lft forever preferred_lft forever
>>>> > >> > >> >>> > 26: ovirtmgmt: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 
>>>> > >> > >> >>> > qdisc
>>>> > >> > >> >>> > noqueue state UP group default qlen 1000
>>>> > >> > >> >>> >     link/ether 90:e2:ba:1e:14:80 brd ff:ff:ff:ff:ff:ff
>>>> > >> > >> >>> >     inet 10.15.28.31/24 brd 10.15.28.255 scope global 
>>>> > >> > >> >>> > ovirtmgmt
>>>> > >> > >> >>> >        valid_lft forever preferred_lft forever
>>>> > >> > >> >>> > 27: ;vdsmdummy;: <BROADCAST,MULTICAST> mtu 1500 qdisc noop 
>>>> > >> > >> >>> > state DOWN
>>>> > >> > >> >>> > group default qlen 1000
>>>> > >> > >> >>> >     link/ether 62:e5:e5:07:99:eb brd ff:ff:ff:ff:ff:ff
>>>> > >> > >> >>> > 29: vnet0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 
>>>> > >> > >> >>> > qdisc mq master
>>>> > >> > >> >>> > ovirtmgmt state UNKNOWN group default qlen 1000
>>>> > >> > >> >>> >     link/ether fe:6f:9c:95:00:02 brd ff:ff:ff:ff:ff:ff
>>>> > >> > >> >>> > [root@swm-02 ~]# free -m
>>>> > >> > >> >>> >               total        used        free      shared  
>>>> > >> > >> >>> > buff/cache   available
>>>> > >> > >> >>> > Mem:          64413        1873       61804           9    
>>>> > >> > >> >>> >      735       62062
>>>> > >> > >> >>> > Swap:         16383           0       16383
>>>> > >> > >> >>> > [root@swm-02 ~]# free -h
>>>> > >> > >> >>> >               total        used        free      shared  
>>>> > >> > >> >>> > buff/cache   available
>>>> > >> > >> >>> > Mem:            62G        1.8G         60G        9.5M    
>>>> > >> > >> >>> >     735M         60G
>>>> > >> > >> >>> > Swap:           15G          0B         15G
>>>> > >> > >> >>> > [root@swm-02 ~]# ls
>>>> > >> > >> >>> > ls                  lsb_release         lshw               
>>>> > >> > >> >>> >  lslocks
>>>> > >> > >> >>> >          lsmod               lspci               lssubsys
>>>> > >> > >> >>> > lsusb.py
>>>> > >> > >> >>> > lsattr              lscgroup            lsinitrd           
>>>> > >> > >> >>> >  lslogins
>>>> > >> > >> >>> >          lsns                lss16toppm          
>>>> > >> > >> >>> > lstopo-no-graphics
>>>> > >> > >> >>> > lsblk               lscpu               lsipc              
>>>> > >> > >> >>> >  lsmem
>>>> > >> > >> >>> >          lsof                lsscsi              lsusb
>>>> > >> > >> >>> > [root@swm-02 ~]# lscpu
>>>> > >> > >> >>> > Architecture:          x86_64
>>>> > >> > >> >>> > CPU op-mode(s):        32-bit, 64-bit
>>>> > >> > >> >>> > Byte Order:            Little Endian
>>>> > >> > >> >>> > CPU(s):                16
>>>> > >> > >> >>> > On-line CPU(s) list:   0-15
>>>> > >> > >> >>> > Thread(s) per core:    2
>>>> > >> > >> >>> > Core(s) per socket:    4
>>>> > >> > >> >>> > Socket(s):             2
>>>> > >> > >> >>> > NUMA node(s):          2
>>>> > >> > >> >>> > Vendor ID:             GenuineIntel
>>>> > >> > >> >>> > CPU family:            6
>>>> > >> > >> >>> > Model:                 44
>>>> > >> > >> >>> > Model name:            Intel(R) Xeon(R) CPU           
>>>> > >> > >> >>> > X5672  @ 3.20GHz
>>>> > >> > >> >>> > Stepping:              2
>>>> > >> > >> >>> > CPU MHz:               3192.064
>>>> > >> > >> >>> > BogoMIPS:              6384.12
>>>> > >> > >> >>> > Virtualization:        VT-x
>>>> > >> > >> >>> > L1d cache:             32K
>>>> > >> > >> >>> > L1i cache:             32K
>>>> > >> > >> >>> > L2 cache:              256K
>>>> > >> > >> >>> > L3 cache:              12288K
>>>> > >> > >> >>> > NUMA node0 CPU(s):     0,2,4,6,8,10,12,14
>>>> > >> > >> >>> > NUMA node1 CPU(s):     1,3,5,7,9,11,13,15
>>>> > >> > >> >>> > Flags:                 fpu vme de pse tsc msr pae mce cx8 
>>>> > >> > >> >>> > apic sep
>>>> > >> > >> >>> > mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse 
>>>> > >> > >> >>> > sse2 ss ht
>>>> > >> > >> >>> > tm pbe syscall nx pdpe1gb rdtscp lm constant_tsc 
>>>> > >> > >> >>> > arch_perfmon pebs bts
>>>> > >> > >> >>> > rep_good nopl xtopology nonstop_tsc aperfmperf eagerfpu 
>>>> > >> > >> >>> > pni pclmulqdq
>>>> > >> > >> >>> > dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm 
>>>> > >> > >> >>> > pcid dca
>>>> > >> > >> >>> > sse4_1 sse4_2 popcnt aes lahf_lm ssbd ibrs ibpb stibp 
>>>> > >> > >> >>> > tpr_shadow vnmi
>>>> > >> > >> >>> > flexpriority ept vpid dtherm ida arat spec_ctrl 
>>>> > >> > >> >>> > intel_stibp flush_l1d
>>>> > >> > >> >>> > [root@swm-02 ~]#
>>>> > >> > >> >>> > _______________________________________________
>>>> > >> > >> >>> > Users mailing list -- users@ovirt.org
>>>> > >> > >> >>> > To unsubscribe send an email to users-le...@ovirt.org
>>>> > >> > >> >>> > Privacy Statement: 
>>>> > >> > >> >>> > https://www.ovirt.org/site/privacy-policy/
>>>> > >> > >> >>> > oVirt Code of Conduct: 
>>>> > >> > >> >>> > https://www.ovirt.org/community/about/community-guidelines/
>>>> > >> > >> >>> > List Archives: 
>>>> > >> > >> >>> > https://lists.ovirt.org/archives/list/users@ovirt.org/message/MTMZ5MF4CF2VR2D25VVPDNFN2IKE24AR/
>>>> > >> > >> >>
>>>> > >> > >> >> _______________________________________________
>>>> > >> > >> >> Users mailing list -- users@ovirt.org
>>>> > >> > >> >> To unsubscribe send an email to users-le...@ovirt.org
>>>> > >> > >> >> Privacy Statement: https://www.ovirt.org/site/privacy-policy/
>>>> > >> > >> >> oVirt Code of Conduct: 
>>>> > >> > >> >> https://www.ovirt.org/community/about/community-guidelines/
>>>> > >> > >> >> List Archives: 
>>>> > >> > >> >> https://lists.ovirt.org/archives/list/users@ovirt.org/message/QBA7NYKAJNREIV6TN42VCW4IN3CX4VFG/
_______________________________________________
Users mailing list -- users@ovirt.org
To unsubscribe send an email to users-le...@ovirt.org
Privacy Statement: https://www.ovirt.org/site/privacy-policy/
oVirt Code of Conduct: 
https://www.ovirt.org/community/about/community-guidelines/
List Archives: 
https://lists.ovirt.org/archives/list/users@ovirt.org/message/DQP6PNUL7VFTVWEKZYO74LBILE7V6LRI/

Reply via email to