Dear Kaspar
Thank you again for the reply. I run the microcoap_example in native
board and now I want to upload the experiment in a M3 node ( only the
coap-server ) . CoAP client ( I take it from libcoap ) will be in my
pc ( linux process ) and I send request from client to take a response
from server ( coap-client "coap://[(IPv6 of
Coap-server)%tap0]:(Port)/riot/board ). But because of FIT-IoT lab and
IPv6, I found that I need a border router. If i can avoid border
router and make this connection, its ok.
You propose me ethos. So I can add the lines as recomended in my CoAP
application.
Something that I must figure out.
compile ethos by running "make" in "dist/tools/ethos"
run ethos in "dist/tools/ethos": "ethos tap0 <your-iotlab-m3-serial-port>"
Which is <iotlab-m3-serial-port> ?
( Sorry if something is really obvious but I am new in all these )
All the best
Theodore
Quoting Kaspar Schleiser <[email protected]>:
Hey Theodore,
do you want to use a border router?
If not,
- add the lines as recommended in "dist/tools/ethos/README.md" to
your application's Makefile
- also add "CFLAGS += '-DSTDIO_BAUDRATE=115200'"
- remove "USEMODULE += gnrc_slip" (if any)
- compile & flash the node
- compile ethos by running "make" in "dist/tools/ethos"
- run ethos in "dist/tools/ethos": "ethos tap0 <your-iotlab-m3-serial-port>"
At this point, you should have serial output of the node showing up
as output of the ethos command.
If you've tried with the microcoap_server example, there'll be no
output after some initial status. Try calling "BOARD=iotlab-m3 make
reset" in examples/microcoap_server, in another shell.
If you can see output, "only" thing left is configuring the network.
Kaspar
On 03/11/2016 11:49 AM, Theodore Kotsonis wrote:
Dear Martine
Thank you for the reply. I have seen ethos but I don't know how to use
it. I have seen the documentation
but I need some steps and a little bit explanation
All the best
Theodore
Quoting Martine Lenders <[email protected]>:
Hi,
first of all sorry that nobody replied to your earlier mail. Did you
have a
look at ethos? It provides an Ethernet over the serial line and should
also
work on the IoT-Lab.
Hope this was helpful.
Martine
Am 11.03.2016 11:26 schrieb "Theodore Kotsonis" <[email protected]>:
Dear RIOT-Users
Someone can help with this.
All the best
Theodore
Quoting Theodore Kotsonis <[email protected]>:
Hi everyone
I am trying to use microcoap example from RIOT repository in FIT-IoT
LAB. So I upload microcoap in an M3 node and I have a CoAP-client in my
linux pc. I want to make a remote connection ( coap-client from
my pc ask for a resource from coap-server in M3 node). I need a Border
Router.
So I will use another m3 node for that purpose. Is there any border
router for m3 node available?
Is there any other way to make this remote connection?
All the best
Theodore
_______________________________________________
users mailing list
[email protected]
https://lists.riot-os.org/mailman/listinfo/users
_______________________________________________
users mailing list
[email protected]
https://lists.riot-os.org/mailman/listinfo/users
_______________________________________________
users mailing list
[email protected]
https://lists.riot-os.org/mailman/listinfo/users
_______________________________________________
users mailing list
[email protected]
https://lists.riot-os.org/mailman/listinfo/users
_______________________________________________
users mailing list
[email protected]
https://lists.riot-os.org/mailman/listinfo/users
