STM32: 112KB at 2000 0000 16KB at 2001 C000 external sram : 1MB at 0x68000000
does MEMORY layout support RAM2? On Fri, Jun 14, 2019 at 10:13 PM Christian Mauderer < christian.maude...@embedded-brains.de> wrote: > If you have already added the chip and it is initialized during startup, > you most likely have to add a section for it in your linker command > file. Depending on where your internal RAM is located and where the > external one is: If they are continuous that can be enough. > > Best regards > > Christian > > On 14/06/2019 04:42, Jython wrote: > > we have added 1M ram by FSMC, and want to manage it by system malloc > > controler > > > > On Fri, Jun 14, 2019 at 10:26 AM Mr. Andrei Chichak <gro...@chichak.ca > > <mailto:gro...@chichak.ca>> wrote: > > > > A 407 doesn’t normally have external RAM. > > > > ARMs have flash at 0 and the 407 has RAM at 0x2000 0000 as you > > discussed earlier. > > > > If you want to work with external flash or RAM, you have to set up > > the FSMC or FMC to support it, but that isn’t a part of the dev > > board that Sebastian used for the BSP port. > > > > The external memory is going to be very specific to your board. > > Which board are you working with? > > > > A > > > > > On 2019-June-13, at 06:23, Christian Mauderer > > <christian.maude...@embedded-brains.de > > <mailto:christian.maude...@embedded-brains.de>> wrote: > > > > > > On 05/06/2019 02:55, Jython wrote: > > >> Hello! > > >> > > >> 2. In the normal (non-debugging) case, the linker script still > > >> places the > > >> > > >> .text section near zero, but places the start of the .data and > > .bss > > >> sections at the start location of the MPC555's internal RAM. > The > > >> system startup code then configures the external RAM just > > after the > > >> internal RAM in memory, forming one large block from the two > RAM > > >> devices. > > >> > > >> from https://devel.rtems.org/wiki/TBR/BSP/Ss555 > > >> > > >> but i dont know how to configure the external RAM just after the > > >> internal RAM in memory? > > >> hope you could give me some guide! > > >> > > >> > > > > > > Hello Jython, > > > > > > the documentation you linked is for an MPC. But your subject line > > > mentions an STM32. What controller / BSP are you using? > > > > > > Best regards > > > > > > Christian Mauderer > > > -- > > > -------------------------------------------- > > > embedded brains GmbH > > > Herr Christian Mauderer > > > Dornierstr. 4 > > > D-82178 Puchheim > > > Germany > > > email: christian.maude...@embedded-brains.de > > <mailto:christian.maude...@embedded-brains.de> > > > Phone: +49-89-18 94 741 - 18 > > > Fax: +49-89-18 94 741 - 08 > > > PGP: Public key available on request. > > > > > > Diese Nachricht ist keine geschäftliche Mitteilung im Sinne des > EHUG. > > > _______________________________________________ > > > users mailing list > > > users@rtems.org <mailto:users@rtems.org> > > > http://lists.rtems.org/mailman/listinfo/users > > > > > > _______________________________________________ > > users mailing list > > users@rtems.org > > http://lists.rtems.org/mailman/listinfo/users > > > > -- > -------------------------------------------- > embedded brains GmbH > Herr Christian Mauderer > Dornierstr. 4 > D-82178 Puchheim > Germany > email: christian.maude...@embedded-brains.de > Phone: +49-89-18 94 741 - 18 > Fax: +49-89-18 94 741 - 08 > PGP: Public key available on request. > > Diese Nachricht ist keine geschäftliche Mitteilung im Sinne des EHUG. >
_______________________________________________ users mailing list users@rtems.org http://lists.rtems.org/mailman/listinfo/users