>On Thu, 3 Mar 2005 02:16:03 -0500, George Georgalis <[EMAIL PROTECTED]> wrote:
>> I'm very defiantly seeing a problem with the 2.6.11
>> kernel and my spamassassin setup. However, it's not
>> clear exactly where the problem is, seems like sa
>> but it might be 2.6.11 with daemontools + qmail +
>> QMAIL_QUEUE.
>>
>> I don't really have time to break down an analysis,
>> but I'm fairly certain. If anyone is experiencing
>> the problem please contact me on or off the list.
>>
>> A sure sign of it is no logs (with debug) for remote
>> sa connections which score "0/0" and correct operation
>> with "cat spam.txt | spamc -R"; fix is to use the
>> older kernel.
Per request here are some logs, I will reboot into 2.6.11 if the
below dmesg doesn't give you details you need. These logs are from the
first sa failure I noticed. (The first timestamp colmn is my local
timezone, EST, it looks like SA logs in UTC)
This log entry indicates when I booted into 2.6.11:
2005-03-02 12:05:47.018334500 2005-03-02 17:05:47 [781] i: server killed by
SIGTERM, shutting down
The following entry was a manual "cat spam.txt | spamc -R" the test
was done because sa stopped logging and startes scoring "0/0" for
everything, obviously the locat test worked:
2005-03-02 17:29:22.627607500 2005-03-02 22:29:22 [895] i: connection from
sta.local [192.168.80.50] at port 36492
# connection to my QMAIL_QUEUE from tcpserver, spam is from 82.229.134.94:
2005-03-02 17:03:45.459533500 tcpserver: status: 0/4
2005-03-02 17:04:07.779403500 tcpserver: status: 1/4
2005-03-02 17:04:07.779409500 tcpserver: pid 4074 from 82.229.134.94
2005-03-02 17:04:09.373336500 tcpserver: ok 4074 sta.galis.org:192.168.80.50:25
facultes-4-82-229-134-94.fbx.proxad.net:82.229.134.94::3682
2005-03-02 17:04:51.556172500 tcpserver: status: 2/4
2005-03-02 17:04:51.556179500 tcpserver: pid 4075 from 209.61.182.217
2005-03-02 17:04:51.557168500 tcpserver: ok 4075 sta.galis.org:192.168.80.50:25
rince.africaninspace.com:209.61.182.217::41362
2005-03-02 17:04:51.959217500 tcpserver: end 4075 status 0
2005-03-02 17:04:51.959224500 tcpserver: status: 1/4
2005-03-02 17:05:43.461588500 tcpserver: end 4074 status 0
2005-03-02 17:05:43.461595500 tcpserver: status: 0/4
# logs from sa
2005-03-02 11:06:43.353479500 2005-03-02 16:06:43 [899] i: checking message
<[EMAIL PROTECTED]> for qmaild:1002.
2005-03-02 11:06:45.942978500 2005-03-02 16:06:45 [899] i: clean message
(-0.8/4.0) for qmaild:1002 in 2.0 seconds, 3099 bytes.
2005-03-02 11:06:45.942987500 2005-03-02 16:06:45 [899] i: result: . 0 -
GEO_TO scantime=2.0,size=3099,mid=<[EMAIL PROTECTED]>,autolearn=disabled
2005-03-02 11:30:49.192464500 2005-03-02 16:30:49 [900] i: connection from
localhost [127.0.0.1] at port 33218
2005-03-02 11:30:49.206473500 2005-03-02 16:30:49 [900] i: checking message
<[EMAIL PROTECTED]> for qmaild:1002.
2005-03-02 11:30:51.826020500 2005-03-02 16:30:51 [900] i: clean message
(0.1/4.0) for qmaild:1002 in 2.0 seconds, 4223 bytes.
2005-03-02 11:30:51.826030500 2005-03-02 16:30:51 [900] i: result: . 0 - TW_XM
scantime=2.0,size=4223,mid=<[EMAIL PROTECTED]>,autolearn=disabled
2005-03-02 11:59:45.509284500 2005-03-02 16:59:45 [898] i: connection from
localhost [127.0.0.1] at port 33227
2005-03-02 11:59:45.521365500 2005-03-02 16:59:45 [898] i: checking message
<[EMAIL PROTECTED]> for qmaild:1002.
2005-03-02 11:59:49.097678500 2005-03-02 16:59:49 [898] i: clean message
(-0.8/4.0) for qmaild:1002 in 4.0 seconds, 2652 bytes.
2005-03-02 11:59:49.097689500 2005-03-02 16:59:49 [898] i: result: . 0 -
GEO_TO scantime=4.0,size=2652,mid=<[EMAIL PROTECTED]>,autolearn=disabled
2005-03-02 12:05:47.018334500 2005-03-02 17:05:47 [781] i: server killed by
SIGTERM, shutting down
2005-03-02 12:09:24.358948500 2005-03-02 17:09:24 [810] i: server started on
port 783/tcp (running version 3.0.2)
2005-03-02 12:09:24.380867500 2005-03-02 17:09:24 [810] i: server successfully
spawned child process, pid 895
2005-03-02 12:09:24.380876500 2005-03-02 17:09:24 [810] i: server successfully
spawned child process, pid 896
2005-03-02 12:09:24.381256500 2005-03-02 17:09:24 [810] i: server successfully
spawned child process, pid 897
2005-03-02 17:29:22.627607500 2005-03-02 22:29:22 [895] i: connection from
sta.local [192.168.80.50] at port 36492
2005-03-02 17:29:22.650336500 2005-03-02 22:29:22 [895] i: checking message
<[EMAIL PROTECTED]@huhmail.com> for geo:1002.
2005-03-02 17:29:26.252961500 2005-03-02 22:29:26 [895] i: identified spam
(33.3/4.0) for geo:1002 in 4.0 seconds, 2371 bytes.
2005-03-02 17:29:26.252970500 2005-03-02 22:29:26 [895] i: result: Y 33 -
GEO_BAD_TO,GEO_LIST_TO,HELO_DYNAMIC_IPADDR,MIME_BOUND_DD_DIGITS,RATWARE_RCVD_AT,SARE_HEAD_MIME_PROD,SARE_MSGID_DBL_AT,SARE_RAND_2,SARE_RAND_2W,UNRESOLVED_TEMPLATE,URIBL_SBL,X_MESSAGE_INFO
scantime=4.0,size=2371,mid=<[EMAIL PROTECTED]@huhmail.com>,autolearn=disabled
###### end of current at Wed Mar 2 20:34:51 EST 2005 #########
# log from qmail send
2005-03-02 17:04:51.863130500 new msg 7274
2005-03-02 17:04:51.863583500 info msg 7274: bytes 2907 from <[EMAIL
PROTECTED]> qp 4085 uid 1002
2005-03-02 17:04:51.873197500 starting delivery 289: msg 7274 to local [EMAIL
PROTECTED]
2005-03-02 17:04:51.874024500 status: local 1/10 remote 0/20
2005-03-02 17:04:51.970617500 delivery 289: success: did_1+0+2/
2005-03-02 17:04:51.971849500 status: local 0/10 remote 0/20
2005-03-02 17:04:51.971855500 end msg 7274
2005-03-02 17:05:29.391984500 new msg 7274
2005-03-02 17:05:29.392434500 info msg 7274: bytes 2463 from <[EMAIL
PROTECTED]> qp 4103 uid 1002
2005-03-02 17:05:29.402267500 starting delivery 290: msg 7274 to local [EMAIL
PROTECTED]
2005-03-02 17:05:29.403089500 status: local 1/10 remote 0/20
2005-03-02 17:05:29.492484500 delivery 290: success: did_1+0+2/
2005-03-02 17:05:29.493667500 status: local 0/10 remote 0/20
2005-03-02 17:05:29.493672500 end msg 7274
# the referenced spam message, sanitized subject.
>From [EMAIL PROTECTED] Wed Mar 2 17:05:29 2005
Return-Path: <[EMAIL PROTECTED]>
Delivered-To: [EMAIL PROTECTED]
Received: (qmail 4103 invoked from network); 2 Mar 2005 22:05:29 -0000
Received: from facultes-4-82-229-134-94.fbx.proxad.net (82.229.134.94)
by sta.galis.org with SMTP; 2 Mar 2005 22:05:06 -0000
X-Message-Info: HVI+uie/25+nr/OTE+9/81703120453
Received: from [EMAIL PROTECTED] ([82.229.134.94]) by [EMAIL PROTECTED] with
Microsoft SMTPSVC(5.0.1636.4684);
Thu, 03 Mar 2005 01:03:41 +0300
Received: from [EMAIL PROTECTED] ([EMAIL PROTECTED] [82.229.134.94])
by [EMAIL PROTECTED] (Postfix) with SMTP id 776FJR388G32WTON
for <[EMAIL PROTECTED]>; Wed, 02 Mar 2005 16:05:41 -0600
X-Message-Info: QTDYM+%ND_LC_CHAR[1-3]58+pz+NFY+892/4753447138988
Received: (qmail 48037 invoked by uid 298); Thu, 03 Mar 2005 01:59:41 +0400
Date: Wed, 02 Mar 2005 14:58:41 -0700
Message-Id: <[EMAIL PROTECTED]@huhmail.com>
From: Winnie Mayo <[EMAIL PROTECTED]>
To: 3ageorgw <[EMAIL PROTECTED]>
Subject: Jack Rabbit xxxxxxxxxx Features:
MIME-Version: 1.0 (produced by paramagneticdrugstore 3.1)
Content-Type: multipart/alternative;
boundary="--782766396549570929"
X-spamc: 0/0 by sta.galis.org; Wed, 2 Mar 2005 17:05:29 -0500
X-tcpremoteip: 82.229.134.94
# dmesg from a 2.6.8.1 kernel, front lost in queue.
st 4:
697eaf0aca3a3aea3a75164746ffaa79
pass
test 5:
56461ef2342edc00f9bab995690efd4c
pass
test 6:
6b1ab7fe4bd7bf8f0b62e6ce61b9d0cd
pass
test 7:
6f630fad67cda0ee1fb1f562db3aa53e
pass
testing hmac_md5 across pages
test 1:
750c783e6ab0b503eaa86e310a5db738
pass
testing hmac_sha1
test 1:
b617318655057264e28bc0b6fb378c8ef146be00
pass
test 2:
effcdf6ae5eb2fa2d27416d5f184df9c259a7c79
pass
test 3:
125d7342b9ac11cd91a39af48aa17b4f63f175d3
pass
test 4:
4c9007f4026250c6bc8414f9bf50c86c2d7235da
pass
test 5:
4c1a03424b55e07fe7f27be1d58bb9324a9a5a04
pass
test 6:
aa4ae5e15272d00e95705637ce8a3b55ed402112
pass
test 7:
e8e99d0f45237d786d6bbaa7965c7808bbff1a91
pass
testing hmac_sha1 across pages
test 1:
effcdf6ae5eb2fa2d27416d5f184df9c259a7c79
pass
testing hmac_sha256
test 1:
a21b1f5d4cf4f73a4dd939750f7a066a7f98cc131cb16a6692759021cfab8181
pass
test 2:
104fdc1257328f08184ba73131c53caee698e36119421149ea8c712456697d30
pass
test 3:
470305fc7e40fe34d3eeb3e773d95aab73acf0fd060447a5eb4595bf33a9d1a3
pass
test 4:
198a607eb44bfbc69903a0f1cf2bbdc5ba0aa3f3d9ae3c1c7a3b1696a0b68cf7
pass
test 5:
5bdcc146bf60754e6a042426089575c75a003f089d2739839dec58b964ec3843
pass
test 6:
cdcb1220d1ecccea91e53aba3092f962e549fe6ce9ed7fdc43191fbde45c30b0
pass
test 7:
d4633c17f6fb8d744c66dee0f8f074556ec4af55ef07998541468eb49bd2e917
pass
test 8:
7546af01841fc09b1ab9c3749a5f1c17d4f589668a587b2700a9c97c1193cf42
pass
test 9:
6953025ed96f0c09f80a96f78e6538dbe2e7b820e3dd970e7ddd39091b32352f
pass
test 10:
6355ac22e890d0a3c8481a5ca4825bc884d3e7a1ff98a2fc2ac7d8e064c3b2e6
pass
testing hmac_sha256 across pages
test 1:
5bdcc146bf60754e6a042426089575c75a003f089d2739839dec58b964ec3843
pass
testing michael_mic
failed to load transform for michael_mic
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU0] (supports C1 C2, 2 throttling states)
lp: driver loaded but no devices found
Real Time Clock Driver v1.12
hw_random hardware driver 1.0.0 loaded
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA CLE266 chipset
agpgart: Maximum main memory to use for agp memory: 816M
agpgart: AGP aperture is 64M @ 0xe0000000
Hangcheck: starting hangcheck timer 0.5.0 (tick is 180 seconds, margin is 60
seconds).
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 [PCSPP(,...)]
lp0: using parport0 (polling).
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
via-rhine.c:v1.10-LK1.1.20-2.6 May-23-2004 Written by Donald Becker
ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 11 (level, low) -> IRQ 11
eth0: VIA Rhine II at 0xeb001000, 00:40:63:d7:ab:83, IRQ 11.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI interrupt 0000:00:11.1[A] -> GSI 11 (level, low) -> IRQ 11
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xa000-0xa007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xa008-0xa00f, BIOS settings: hdc:DMA, hdd:pio
hdc: CD-ROM 50X L, ATAPI CD/DVD-ROM drive
Using anticipatory io scheduler
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 50X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.02 loaded.
sata_sil version 0.54
ACPI: PCI interrupt 0000:00:14.0[A] -> GSI 10 (level, low) -> IRQ 10
ata1: SATA max UDMA/100 cmd 0xF8889080 ctl 0xF888908A bmdma 0xF8889000 irq 10
ata2: SATA max UDMA/100 cmd 0xF88890C0 ctl 0xF88890CA bmdma 0xF8889008 irq 10
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:207f
ata1: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48
ata1(0): applying Seagate errata fix
ata1: dev 0 configured for UDMA/100
scsi0 : sata_sil
ata2: no device found (phy stat 00000000)
scsi1 : sata_sil
Vendor: ATA Model: ST3160023AS Rev: 3.18
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
ohci1394: $Rev: 1223 $ Ben Collins <[EMAIL PROTECTED]>
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 10 (level, low) -> IRQ 10
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[eb003000-eb0037ff]
Max Packet=[2048]
video1394: Installed video1394 module
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ACPI: PCI interrupt 0000:00:10.3[D] -> GSI 5 (level, low) -> IRQ 5
ehci_hcd 0000:00:10.3: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.3: reset hcs_params 0x3206 dbg=0 cc=3 pcc=2 ordered !ppc
ports=6
ehci_hcd 0000:00:10.3: reset hcc_params 6872 thresh 7 uframes 256/512/1024
ehci_hcd 0000:00:10.3: capability 0001 at 68
ehci_hcd 0000:00:10.3: irq 5, pci mem f889f000
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.3: reset command 080002 (park)=0 ithresh=8 period=1024
Reset HALT
ehci_hcd 0000:00:10.3: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
ehci_hcd 0000:00:10.3: supports USB remote wakeup
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: default language 0x0409
usb usb1: Product: VIA Technologies, Inc. USB 2.0
usb usb1: Manufacturer: Linux 2.6.8.1-sta ehci_hcd
usb usb1: SerialNumber: 0000:00:10.3
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:10.0: irq 11, io base 00009400
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: detected 2 ports
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: default language 0x0409
usb usb2: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
usb usb2: Manufacturer: Linux 2.6.8.1-sta uhci_hcd
usb usb2: SerialNumber: 0000:00:10.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
ACPI: PCI interrupt 0000:00:10.1[B] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(#2)
uhci_hcd 0000:00:10.1: irq 10, io base 00009800
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: detected 2 ports
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: default language 0x0409
usb usb3: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
usb usb3: Manufacturer: Linux 2.6.8.1-sta uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
ACPI: PCI interrupt 0000:00:10.2[C] -> GSI 12 (level, low) -> IRQ 12
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(#3)
uhci_hcd 0000:00:10.2: irq 12, io base 00009c00
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: detected 2 ports
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: default language 0x0409
usb usb4: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
usb usb4: Manufacturer: Linux 2.6.8.1-sta uhci_hcd
usb usb4: SerialNumber: 0000:00:10.2
usb usb4: hotplug
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: hotplug
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: PC Speaker
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
ehci_hcd 0000:00:10.3: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
input: AT Translated Set 2 keyboard on isa0060/serio0
I2O Core - (C) Copyright 1999 Red Hat Software
I2O: Event thread created as pid 188
i2o: Checking for PCI I2O controllers...
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
I2O Block Storage OSM v0.9
(c) Copyright 1999-2001 Red Hat Software.
i2o_block: Checking for Boot device...
i2o_block: Checking for I2O Block devices...
i2o_scsi.c: Version 0.1.2
chain_pool: 0 bytes @ f7df21c0
(512 byte buffers X 4 can_queue X 0 i2o controllers)
i2c /dev entries driver
md: raid1 personality registered as nr 3
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: [EMAIL PROTECTED]
Advanced Linux Sound Architecture Driver Version 1.0.4 (Mon May 17 14:31:44
2004 UTC).
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 12 (level, low) -> IRQ 12
PCI: Setting latency timer of device 0000:00:11.5 to 64
hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501
hub 1-0:1.0: port 4 not reset yet, waiting 50ms
ehci_hcd 0000:00:10.3: port 4 high speed
ehci_hcd 0000:00:10.3: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 1-4: new high speed USB device using address 2
ehci_hcd 0000:00:10.3: devpath 4 ep0out 3strikes
ehci_hcd 0000:00:10.3: devpath 4 ep0out 3strikes
usbcore: registered new driver snd-usb-audio
ALSA device list:
#0: VIA 8235 at 0xa400, irq 12
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
ip_conntrack version 2.1 (7168 buckets, 57344 max) - 296 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <[EMAIL PROTECTED]>.
http://snowman.net/projects/ipt_recent/
IPVS: Registered protocols (TCP, UDP, AH, ESP)
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
usb 1-4: device not accepting address 2, error -71
IPVS: ipvs loaded.
IPVS: [rr] scheduler registered.
IPVS: [sed] scheduler registered.
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
ReiserFS: sda1: found reiserfs format "3.6" with standard journal
ReiserFS: sda1: using ordered data mode
ReiserFS: sda1: journal params: device sda1, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda1: checking transaction log (sda1)
ReiserFS: sda1: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 208k freed
hub 1-0:1.0: port 4 not reset yet, waiting 50ms
ehci_hcd 0000:00:10.3: port 4 high speed
ehci_hcd 0000:00:10.3: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 1-4: new high speed USB device using address 3
ehci_hcd 0000:00:10.3: devpath 4 ep0in 3strikes
ehci_hcd 0000:00:10.3: devpath 4 ep0out 3strikes
ieee1394: Host added: ID:BUS[0-00:1023] GUID[004063500001b505]
ehci_hcd 0000:00:10.3: devpath 4 ep0out 3strikes
usb 1-4: device not accepting address 3, error -71
ehci_hcd 0000:00:10.3: GetStatus port 5 status 001030 POWER sig=se0 OCC OC
hub 1-0:1.0: over-current change on port 5
hub 1-0:1.0: enabling power on all ports
ehci_hcd 0000:00:10.3: GetStatus port 6 status 001030 POWER sig=se0 OCC OC
hub 1-0:1.0: over-current change on port 6
hub 1-0:1.0: enabling power on all ports
uhci_hcd 0000:00:10.0: port 1 portsc 008a
hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
Adding 1638620k swap on /dev/sda2. Priority:-1 extents:1
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.0: port 2 portsc 008a
hub 2-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.1: port 1 portsc 008a
hub 3-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.1: port 2 portsc 009a
hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.2: port 1 portsc 048a
hub 4-0:1.0: port 1, status 0108, change 0003, 12 Mb/s
hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x108
uhci_hcd 0000:00:10.2: port 2 portsc 048a
hub 4-0:1.0: port 2, status 0108, change 0003, 12 Mb/s
uhci_hcd 0000:00:10.0: suspend_hc
hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x108
uhci_hcd 0000:00:10.1: suspend_hc
uhci_hcd 0000:00:10.2: suspend_hc
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
ReiserFS: sda4: found reiserfs format "3.6" with standard journal
ReiserFS: sda4: using ordered data mode
ReiserFS: sda4: journal params: device sda4, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda4: checking transaction log (sda4)
ReiserFS: sda4: Using r5 hash to sort names
eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
The 2.6.11 config is nearly identical, and I can provide that dmesg if this is
insufficent info.
Thanks,
// George
--
George Georgalis, systems architect, administrator Linux BSD IXOYE
http://galis.org/george/ cell:646-331-2027 mailto:[EMAIL PROTECTED]
