Hi Konstantin,

Can you please attach the picture of the back label?

Regards,
Nate Temple


> On Aug 8, 2017, at 12:29 PM, Matheou, Konstantin J. (GRC-LCI0)[ZIN 
> TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> wrote:
> 
> I am wearing my reading glasses and the letters were very small too...
> 
> I took the picture and zoomed in on it with my phone..
> 
> It is 3117FF1....
> 
> 
> 
> -----Original Message-----
> From: Nate Temple [mailto:nate.tem...@ettus.com] 
> Sent: Tuesday, August 08, 2017 3:25 PM
> To: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] 
> <konstantin.j.math...@nasa.gov>
> Cc: Marcus Müller <marcus.muel...@ettus.com>; usrp-users 
> <usrp-users@lists.ettus.com>
> Subject: Re: [USRP-users] When ssh'ing Getting prompt for Password Issue
> 
> Hi Konstantin,
> 
> Also, looking up the serial number 8117FF1 didn't not result in any matches.
> 
> Can you please send a picture of the back label so we can clearly see the 
> numbers on the label?
> 
> 
> Regards,
> Nate Temple
> 
> 
> 
> 
>> On Aug 8, 2017, at 12:23 PM, Nate Temple <nate.tem...@ettus.com> wrote:
>> 
>> Hi Konstantin,
>> 
>> The partition table looks like it is OK.
>> 
>> I would suggest trying to redownload the release-4 / SpeedGrade3 images 
>> again and try burning them to the SD Card again. Verify that the md5sums 
>> match what is posted in the SG3/ folder. 
>> 
>> The error you're seeing has only came up when the incorrect SpeedGrade image 
>> is used.
>> 
>> Regards,
>> Nate Temple
>> 
>> 
>> 
>> 
>>> On Aug 8, 2017, at 11:59 AM, Matheou, Konstantin J. (GRC-LCI0)[ZIN 
>>> TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> wrote:
>>> 
>>> Nate,
>>> 
>>> I hope there is no issue with the hardware... OK.. we are now in debug mode 
>>> I guess...  I hope you can hang out a little quicker with me to get this 
>>> resolved...  I appreciate it...
>>> 
>>> Below is the Disk Management program screen shot and I placed the files 
>>> that got placed on the micro SD card....  Again it was the file from 
>>> release4/...sg3/ - again I have the E310 E.
>>> 
>>> This is the backup micro SD card….  And the micro SD card that came with 
>>> the unit (visually checked) looked exactly the same….
>>> 
>>> <image001.jpg>
>>> 
>>> 
>>> 
>>> 
>>> -----Original Message-----
>>> From: Nate Temple [mailto:nate.tem...@ettus.com] 
>>> Sent: Tuesday, August 08, 2017 2:35 PM
>>> To: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] 
>>> <konstantin.j.math...@nasa.gov>
>>> Cc: Marcus Müller <marcus.muel...@ettus.com>; usrp-users 
>>> <usrp-users@lists.ettus.com>
>>> Subject: Re: [USRP-users] When ssh'ing Getting prompt for Password Issue
>>> 
>>> Hi Konstantin,
>>> 
>>> I don't suspect that there is any issue at all with the hardware. It is 
>>> most likely due to the image or partition table on the SD card not being 
>>> setup correctly.
>>> 
>>> Can you please open the Disk Management program within Windows and with the 
>>> SD card inserted, take a screen capture of the partition layout for the SD 
>>> Card?
>>> 
>>> Regards,
>>> Nate Temple
>>> 
>>>> On Aug 8, 2017, at 11:16 AM, Matheou, Konstantin J. (GRC-LCI0)[ZIN 
>>>> TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> wrote:
>>>> 
>>>> Nate,
>>>> 
>>>> I also tried release 4 sg1 directory dev.direct file...  same error as 
>>>> below...
>>>> 
>>>> I also tried release 3 dev.direct...  Was able to log in through root... 
>>>> made the vi alterations to the interfaces file...  but was unable to 
>>>> ping...
>>>> 
>>>> Here is the E310 info:
>>>> 
>>>> P/N 156333E-01L
>>>> 
>>>> S/N 8117FF1
>>>> 
>>>> How soon can I get another E310 shipped to me???  Unfortunately, I need to 
>>>> have a design ready for my project by early September.  I really need a 
>>>> replacement pretty fast, if possible?
>>>> 
>>>> Thanks,
>>>> 
>>>> Konstantin
>>>> 
>>>> -----Original Message-----
>>>> From: Nate Temple [mailto:nate.tem...@ettus.com]
>>>> Sent: Tuesday, August 08, 2017 1:21 PM
>>>> To: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] 
>>>> <konstantin.j.math...@nasa.gov>
>>>> Cc: Marcus Müller <marcus.muel...@ettus.com>; usrp-users 
>>>> <usrp-users@lists.ettus.com>
>>>> Subject: Re: [USRP-users] When ssh'ing Getting prompt for Password Issue
>>>> 
>>>> Hi Konstantin,
>>>> 
>>>> Can you please send the full part number and serial number for your 
>>>> device. It is located on the label on the bottom side of the E3xx. ( "P/N: 
>>>> XXXXXX", "S/N: XXXXXXX" )
>>>> 
>>>> Regards,
>>>> Nate Temple
>>>> 
>>>> 
>>>>> On Aug 8, 2017, at 8:33 AM, Matheou, Konstantin J. (GRC-LCI0)[ZIN 
>>>>> TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> wrote:
>>>>> 
>>>>> OK…  Used the backup microSD we ordered.  Reprogrammed it with the same 
>>>>> .direct file…  Same error as below…
>>>>> 
>>>>> “Unable to read file uImage-zynq-e31x-3.dtb”
>>>>> 
>>>>> Now, either I am loading a incorrect image, or something is not working 
>>>>> correctly with the unit.
>>>>> 
>>>>> Please tell me your thoughts…
>>>>> 
>>>>> Thanks…
>>>>> 
>>>>> From: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC]
>>>>> Sent: Tuesday, August 08, 2017 11:29 AM
>>>>> To: 'Nate Temple' <nate.tem...@ettus.com>; 'Marcus Müller' 
>>>>> <marcus.muel...@ettus.com>
>>>>> Cc: 'usrp-users' <usrp-users@lists.ettus.com>
>>>>> Subject: RE: [USRP-users] When ssh'ing Getting prompt for Password Issue
>>>>> 
>>>>> Btw.. just to validate what image I used…
>>>>> 
>>>>> I have the E310 E version…
>>>>> 
>>>>> The instructions I think may not be correct…  Here they are cut and 
>>>>> paste…  Please validate….
>>>>> 
>>>>> For the E310, the product number will be 156333X-01L, where X is a letter 
>>>>> from A to Z. For devices where X is A, B, C, D, the images under the 
>>>>> "ettus-e3xx-sg1" folder should be used. For devices where X is E or 
>>>>> later, the images under the "ettus-e3xx-sg3" folder should be used. (WHAT 
>>>>> I USED) You must use the appropriate image for your specific device. The 
>>>>> incorrect image will not work, and will only boot as far as the U-Boot 
>>>>> boot loader before stopping.
>>>>> 
>>>>> 
>>>>> 
>>>>> BUT this is what is written also…
>>>>> 
>>>>> 
>>>>> 
>>>>> For the E312, the product number will be 140605X-01L, where X is a letter 
>>>>> from A to Z. The images under the "ettus-e3xx-sg3" folder should be used 
>>>>> for all E312 devices.
>>>>> 
>>>>> 
>>>>> So you told me to go to release 4 (also the directions did)…  and then I 
>>>>> chose the sg3 directory – Is this correct???  Thus, both the E310 E and 
>>>>> E312 devices use the sg3 directory????
>>>>> 
>>>>> I used the Ettus-3xx-sg3 directory and downloaded those versions.  I am 
>>>>> assuming they are the correct versions.
>>>>> 
>>>>> Thanks…
>>>>> 
>>>>> From: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC]
>>>>> Sent: Tuesday, August 08, 2017 11:15 AM
>>>>> To: 'Nate Temple' <nate.tem...@ettus.com>; Marcus Müller 
>>>>> <marcus.muel...@ettus.com>
>>>>> Cc: usrp-users <usrp-users@lists.ettus.com>
>>>>> Subject: RE: [USRP-users] When ssh'ing Getting prompt for Password Issue
>>>>> 
>>>>> Nate,
>>>>> 
>>>>> The instructions are very well written and detailed.. Thanks…
>>>>> 
>>>>> Actually, most of the steps I was doing correctly from all the various 
>>>>> portions of documents.  But it is good you placed all in one document.  
>>>>> Thanks…
>>>>> 
>>>>> Everything worked well up until I burned the image. 
>>>>> 
>>>>> When I did the terminal  command - sudo screen /dev/ttyUSB0 115200 – and 
>>>>> then turned on the E310, I received “Unable to read file 
>>>>> uImage-zynq-e31x-3.dtb”
>>>>> 
>>>>> I tried both tx version – demo and dev…  Both did the same thing…
>>>>> 
>>>>> I have another SD card that we ordered with the unit.  I will try to 
>>>>> re-image that card and see hwat happens…  Of course, I will let you know.
>>>>> 
>>>>> Thanks,
>>>>> 
>>>>> Konstantin
>>>>> 
>>>>> From: Nate Temple [mailto:nate.tem...@ettus.com]
>>>>> Sent: Monday, August 07, 2017 9:29 PM
>>>>> To: Marcus Müller <marcus.muel...@ettus.com>
>>>>> Cc: usrp-users <usrp-users@lists.ettus.com>; Matheou, Konstantin J. 
>>>>> (GRC-LCI0)[ZIN TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov>
>>>>> Subject: Re: [USRP-users] When ssh'ing Getting prompt for Password Issue
>>>>> 
>>>>> Hi Konstantin,
>>>>> 
>>>>> Please see the updated version of the PDF, attached to this email. One of 
>>>>> the screen captures needed to be updated.
>>>>> 
>>>>> Regards,
>>>>> Nate Temple
>>>>> 
>>>>> 
>>>>> 
>>>>> 
>>>>> Previous message
>>>>> -------------------------------
>>>>> Hi Konstantin,
>>>>> 
>>>>> I had an error in my previous email. The default setting for the 
>>>>> release-4 image is to have a DHCP address. You'll need to edit 
>>>>> /etc/network/interfaces and update it to operate with a static IP.
>>>>> 
>>>>> Please see the attached PDF that will walk through the process of burning 
>>>>> the release-4 SD Card image to a blank SD Card, and then the required 
>>>>> steps to configure the Ubuntu VM within the Windows host to connect via 
>>>>> the Serial interface to update the /etc/network/interfaces file, and then 
>>>>> connect via SSH.
>>>>> 
>>>>> Also, with 1GbE connections, you do not need to use a cross over cable. 
>>>>> 1GbE has auto-MDIX which will allow a normal straight through ethernet 
>>>>> cable to be used when directly connecting devices.
>>>>> 
>>>>> Regards,
>>>>> Nate Temple
>>>>> -------------------------------
>>>> 
>> 
> 


_______________________________________________
USRP-users mailing list
USRP-users@lists.ettus.com
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
  • Re:... Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] via USRP-users
  • Re:... Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] via USRP-users
  • Re:... Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] via USRP-users
  • Re:... Nate Temple via USRP-users
  • Re:... Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] via USRP-users
  • Re:... Nate Temple via USRP-users
  • Re:... Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] via USRP-users
  • Re:... Nate Temple via USRP-users
  • Re:... Nate Temple via USRP-users
  • Re:... Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] via USRP-users
  • Re:... Nate Temple via USRP-users
  • Re:... Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] via USRP-users
  • Re:... Nate Temple via USRP-users
  • Re:... Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] via USRP-users
  • Re:... Nate Temple via USRP-users
  • Re:... Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] via USRP-users
  • Re:... Nate Temple via USRP-users
  • Re:... Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] via USRP-users
  • Re:... Nate Temple via USRP-users
  • Re:... Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] via USRP-users
  • Re:... Nate Temple via USRP-users

Reply via email to