Thanks very much Marcus for the thorough explanations. I looked at the phase
change with frequency to see if there was a fixed delay and there didn’t appear
to be but, effectively, the MIMO cable induces a frequency dependent
uncorrected phase offset which is eminently understandable but would appear to
make a mockery of ‘MIMO’ claims. I realised that there will always be a phase
offset but was disappointed by the magnitude as measured by the complex
conjugate of both signals, a complex_to_arg block and decimating the result by
1K and plotting on Qt GUI Time Sink.
It would appear that if I wanted to try to get as close to zero phase offset
(to correct for non-zero MIMO cable length at least), then I need an
Octoclock-G but I don’t have the nearly $NZD 3000.00 it costs so I wonder if
there is a ‘cheap’ way to convert my existing GPSDO board into an Octoclock-G?
I only need to be able to buffer the signal for 2 USRPs.
Otherwise, I guess I could ‘calibrate’ the offset at various frequencies and
then, at run time, apply a phase correction to one leg based on the fc? Seems a
little inelegant.
Kind Regards,
John
From: Marcus D. Leech
Sent: Wednesday, October 25, 2017 1:20 PM
To: John Shields
Cc: usrp-users
Subject: Re: [USRP-users] 2 N200 MIMO system phase offset varies with
frequency, have used timed_command with tune and also integer-N Tuning per
Marcus M post of Feb 17, 2016
On 10/24/2017 07:45 PM, John Shields wrote:
Thanks Marcus,
So it appears that the synching of the SBX LOs
doesn’t work; or perhaps I should say, it doesn’t work during my measurement
period? The integer-N tuning doesn’t work either.
I can say that, with some level of precision, the
phase is fairly constant with center-frequency but if, for example, I had a 5
MHz spectrum how could I ‘correct for that’? I be;ieve that there is the whole
Hilbert transform issue when you wish to translate the phase/frequency of a
band of signals to a different one –is that what I should use?
From my point of view, there is quite a
misinterpretation of what ‘synchronistation’ means; in particular for SBXs and
their LOs which, as advertised, are supposed to be capable of such operation
with a few simple Python commands!.
Realising that you would/should not express some
shortcoming in the SBX,N200,MIMO in an Ettus product , if there is, I would
dearly like to know from someone from Ettus!!!! Purely from an outside point of
view, I thought that the “ we’ll transfer the Time Of Day contents to the Mate
over MIMO cable ” doesn’t actually mean that they are in ‘real time’ synch,
from my old DMS-100 days bit was willing to go along with the theory.
Seriously, I have no issue with that but just want to know how to get 2 N200r4
streams with OB GPSDO & MIMO cable ‘synchronised’
I would love (but be embarrassed) to be told, that as
a dummy, I made this mistake but in over a month of work I have not been able
to establish that.
Kind Regards,
John
Set up a test transmitter in the far-field of your two antenna.
With everything synchronized the way you think it should be, plot the
low-pass-filtered (and decimate to taste) result of a conjugate multiply of
the two sides. This should produce a straight line, with small amounts of
noise. If it just produces random walks all over the place, the two
oscillators aren't locked to the same reference.
My point about component tolerances is that they'll have some group-delay that
isn't perfectly matched on both sides, even if things like the
LO are running in-phase, the analog pathways won't necessarily have precisely
the same group delay on the two sides. Just like two random
pieces of coax that are cut to the same length won't, necessarily, have
precisely the same phase length. This effect gets worse with frequency.
Further, in radio astronomy applications, the coherence bandwidth is,
technically speaking, infinitely small, due to the emission mechanisms.
But in *practice* a significant fractional bandwidth is possible without
having to channelize the input bandwidth.
The *other* issue, that seems to be causing consternation, is the ability to
predict what the phase-offset between the two sides will be upon restart
of the flow-graph in the presence of the various bits of hocus-pocus (timed
commands, etc) to try for consistent phase offsets every time you
start streaming. It sounds like you have that, but the offset changes
depending on tuned frequency. I'd expect that. Both due to analog-component
group-delay variability, and because the MIMO cable is not of zero length. I
don't believe that there is *ANY* length compensation, so one N2XX will
receive the reference clock at a "closer" phase distance than the other one,
because the MIMO cable is of finite length. That phase-length difference will
have more effect at higher frequencies, because a PLL is a reference
multiplier (which is why having exquisitely-low phase-noise on the reference is
important, because that noise will get worse as the multiplier ratio of the
PLL increases).
From: mle...@ripnet.com
Sent: Wednesday, October 25, 2017 7:45 AM
To: John Shields
Cc: usrp-users
Subject: Re: [USRP-users] 2 N200 MIMO system phase offset varies with
frequency, have used timed_command with tune and also integer-N Tuning per
Marcus M post of Feb 17, 2016
I would expect component tolerance issues on the two sides to scale with
frequency. That may be what you're seeing?
On 2017-10-24 14:28, John Shields via USRP-users wrote:
Hi,
Still struggling with the configuration – 2x N200 r4, master O/B GPSDO,
slave MIMO cable. Have put in python code to use timed commands and that
produced a constant phase offset even over rerun of FG or power cycling on N200
which was great news.
However, the relative offset changes with frequency. The splitter is a
Mini-circuits ZRFSC-123S+ which is spec-ed to has a typical of phase unbalance
of 1/2 a degree over the frequency ranges used. The results are independent of
source NWT 4000-1 or an SBX using uhd_siggen. When I have checked the
ref_locked flags etc. they are good. the gpsdo is 'locked' as is MIMO.
In addition to using the timed_commands to synch the SBX LOs, I also
implement the integer-N-tuning and no improvement.
The results are roughly Freq (MHz) Phase offset (deg)
450 -7
1450 -30
1950 -65
2450 -100
When I switch the cables between the 2 N200, the phase offset doesn't
change sign so I presume it is not cabling? What on earth, else, could it be?
Kind Regards,
John
Virus-free. www.avast.com
_______________________________________________
USRP-users mailing list
USRP-users@lists.ettus.com
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
_______________________________________________
USRP-users mailing list
USRP-users@lists.ettus.com
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
