Here is the output:
enp3s0 Link encap:Ethernet HWaddr 68:f7:28:42:64:6b
inet addr:192.168.10.1 Bcast:192.168.10.255 Mask:255.255.255.0
inet6 addr: fe80::c469:ffbe:558:1d0c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:5000 Metric:1
RX packets:129757 errors:0 dropped:0 overruns:0 frame:0
TX packets:146186 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:60283078 (60.2 MB) TX bytes:63747906 (63.7 MB)
________________________________
From: Marcus D. Leech <[email protected]>
Sent: Thursday, September 6, 2018 4:31:28 PM
To: Harper, Andrew; [email protected]
Subject: Re: [USRP-users] USRP Source Block caught rx error code: 15
On 09/06/2018 04:01 PM, Harper, Andrew wrote:
I'm running Xubuntu 16.04 on the hardware, i.e. not VM:
Distributor ID: Ubuntu
Description: Ubuntu 16.04.5 LTS
Release: 16.04
Codename: xenial
Ethernet info:
description: Ethernet interface
product: RTL8111/8168/8411 PCI Express Gigabit Ethernet
Controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:03:00.0<mailto:pci@0000:03:00.0>
logical name: enp3s0
version: 10
serial: 68:f7:28:42:64:6b
size: 1Gbit/s
capacity: 1Gbit/s
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix vpd bus_master cap_list
ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd
autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169
driverversion=2.3LK-NAPI duplex=full firmware=rtl8168g-3_0.0.1 04/23/13
ip=192.168.10.1 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s
resources: irq:27 ioport:3000(size=256)
memory:f0d04000-f0d04fff memory:f0d00000-f0d03fff
What is the frame error count on the interface? (rx errors when using ifconfig)
________________________________
From: USRP-users
<[email protected]><mailto:[email protected]>
on behalf of Marcus D. Leech via USRP-users
<[email protected]><mailto:[email protected]>
Sent: Thursday, September 6, 2018 3:43 PM
To: [email protected]<mailto:[email protected]>
Subject: Re: [USRP-users] USRP Source Block caught rx error code: 15
On 09/06/2018 03:29 PM, Harper, Andrew via USRP-users wrote:
Hi, I am having a troubling error from my x310 USRP whenever I try to pull
samples using the USRP source block. The error message I am getting is:
[ERROR] [STREAMER] The receive packet handler caught a value exception.
ValueError: Bad CHDR or packet fragment
WARN: USRP Source Block caught rx error code: 15
[ERROR] [RX FLOW CTRL] Error unpacking packet: ValueError: Bad CHDR or packet
fragment
The most basic flowgraph that creates this error is a USRP Source connected
directly to a QT Time plot. It also happens when I try to run: 1)
uhd_cal_rx_iq_balance, 2) uhd_fft, 3) uhd_cal_tx_dc_offset, My gnuradio
version is 3.7.13.4, UHD version is UHD 3.14.0.0-88-g6013a511, and i have just
reinstalled both to make sure it is not a software issue. I am able to
successfully run uhd_find_devices and uhd_usrp_probe. I am also able to run a
USRP sink block without error, if that helps identify the problem.
Anyone have a fix for this?
Andrew
What type of Ethernet interface do you have on your system?
Is this a VM, or a on-the-hardware system?
Is this on Windows or Linux?
_______________________________________________
USRP-users mailing list
[email protected]
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
