On 08.02.2013 14:52, Teemu Suikki wrote:
Hi!
As I mentioned in my previous email, I'm using diseqc.conf to drive my
motorized dish.
I noticed that sometimes VDR generates false channe updates, when the dish is
moving. The problem is, channel switches immediately, but it takes seconds for
the dish to move. Often there is several seconds time when VDR thinks it's
already on the new channel, but old satellite is still tuned.
I googled and I noticed something about this in actuator plugin README:
"vdr assumes that, as soon as a channel has been switched to, the new source
(satellite) is valid, even if the dish is moving, so the autoupdate function will
assign new/updated channels to the wrong satellite. The plugin's workaround is to
disable autoupdate while the dish is moving and restore the
previous setting only when it has reached the target satellite. It's possible that the
plugin will fail to restore the value of this setting. If you see that channels aren't
updating anymore check this setting (main menu->configuration->dbv->update
channels, note that while the dish is moving this
setting is always "no", so check and modify it only when the actuator is idle).
"
RotorNG does not have such hack, so it still suffers from this problem. Also as I said, I
use VDR "as is" without rotor-ng, and have this problem.
I made the following patch to sections.c, this is for vdr 1.7.27 but I guess
it's similar in newer VDRs as well..
If source has been changed, it forces a 10 second delay. This means that epg
data and channel updates are disabled during that time, but it shouldn't matter.
10 seconds might not be quite enough to get to the new position with a slow
motor, but it is enough to make the frontend loose lock on the previous
satellite..
Here's also example from syslog:
Feb 8 15:17:23 yavdr vdr: [16352] switching to channel 990
Feb 8 15:17:23 yavdr vdr: [16420] New source 0x5300ff7e, 10sec wait forced in
section loop
Feb 8 15:17:29 yavdr vdr: [16419] frontend 1/0 lost lock on channel 990, tp
112322
Feb 8 15:17:30 yavdr vdr: [16419] frontend 1/0 regained lock on channel 990,
tp 112322
Here you can see how it takes full 6 seconds before frontend reports lost lock,
after channel switch.. Channel is really switched at 15:17:30 when it regains
lock. If any section data would be received between 15:17:23 - 15:17:29, it
would be registered on the wrong satellite.
------------------------------
The patch:
*** vdr-alt/sections.c 2007-10-14 15:52:07.000000000 +0300
--- vdr/sections.c 2013-02-08 14:50:30.524186976 +0200
***************
*** 164,169 ****
--- 164,171 ----
void cSectionHandler::Action(void)
{
+ int PrevSource=shp->channel.Source();
+
SetPriority(19);
while (Running()) {
***************
*** 183,188 ****
--- 185,196 ----
if (poll(pfd, NumFilters, 1000) > 0) {
bool DeviceHasLock = device->HasLock();
+ if (PrevSource!=shp->channel.Source()) {
+ PrevSource=shp->channel.Source();
+ DeviceHasLock = false;
+ dsyslog("New source 0x%x, 10sec wait forced in section
loop\n",PrevSource);
+ cCondWait::SleepMs(10000);
+ }
if (!DeviceHasLock)
cCondWait::SleepMs(100);
for (int i = 0; i < NumFilters; i++) {
While this may be a viable solution for your particular problem, I don't think
putting a general 10s wait in there would be such a good idea. This would be
totally
annoying for users who receive multiple sat positions via a multiswitch, where
switching
between sources is very fast.
I'm wondering whether there is any information in the SI data as to which source
(i.e. satellite) this data is broadcast on. I guess that should help a great
deal in actually
solving this problem.
Klaus
_______________________________________________
vdr mailing list
vdr@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr