Hi Dan,

Thank you for the quick fix and reply!

The output of `brctl show` as follows:

bridge name     bridge id               STP enabled     interfaces
ovirtmgmt               8000.0025907c2c7a       no              eth0
                                                        eth2

It goes away after doing 'brctl delif ovirtmgmt eth0' manually.
I will let you know if we could reproduce this issue again.

Thanks and Regards,
Tim

----- Original Message -----
> From: "Dan Kenigsberg" <dan...@redhat.com>
> To: "Timothy Asir Jeyasingh" <tjeya...@redhat.com>
> Cc: vdsm-devel@lists.fedorahosted.org
> Sent: Wednesday, June 19, 2013 4:03:20 PM
> Subject: Re: [vdsm] Need help on fixing VDSM node non-operational error
> 
> On Wed, Jun 19, 2013 at 05:51:52AM -0400, Timothy Asir Jeyasingh wrote:
> > Hi All,
> > 
> > Currently I am facing some issues while adding a node to an engine.
> > Host comes up initially. Then goes to Non-operational state. On trying to
> > activate the host, it again comes up. Then goes to Non-operational state
> > again and so on.
> > 
> > The following message is seen in the engine Events log multiple times -
> > Bridged network ovirtmgmt is attached to multiple interfaces: eth2,eth0 on
> > Host ...
> > 
> > The following is seen in the engine logs -
> > 2013-06-06 20:52:23,003 INFO
> > [org.ovirt.engine.core.vdsbroker.VdsUpdateRunTimeInfo]
> > (DefaultQuartzScheduler_Worker-16) Host '...' moved to Non-Operational
> > state because interface/s 'eth0, ' are down which needed by network/s
> > 'ovirtmgmt, ' in the current cluster
> > 
> > Additional info:
> > The host is a physical machine. The contents of the file
> > /etc/sysconfig/network-scripts/ifcfg-ovirtmgmt -
> > 
> > # cat /etc/sysconfig/network-scripts/ifcfg-ovirtmgmt
> > DEVICE=ovirtmgmt
> > TYPE=Bridge
> > ONBOOT=yes
> > DELAY=0
> > BOOTPROTO=dhcp
> > NM_CONTROLLED=no
> > 
> > The contents of /etc/sysconfig/network-scripts/ifcfg-eth2
> > 
> > # cat /etc/sysconfig/network-scripts/ifcfg-eth2
> > DEVICE="eth2"
> > BRIDGE="ovirtmgmt"
> > BOOTPROTO="dhcp"
> > HWADDR="00:25:90:93:62:02"
> > IPV6INIT="yes"
> > IPV6_AUTOCONF="yes"
> > NM_CONTROLLED="yes"
> > ONBOOT="yes"
> > TYPE="Ethernet"
> > 
> > The contents of /etc/sysconfig/network-scripts/ifcfg-eth0 -
> > 
> > # cat /etc/sysconfig/network-scripts/ifcfg-eth0
> > DEVICE="eth0"
> > HWADDR="00:25:90:7C:2C:7A"
> > NM_CONTROLLED="yes"
> > ONBOOT="yes"
> > 
> > 
> > Can someone give some suggestion for this issue!
> 
> I've had a couple of questions on
> https://bugzilla.redhat.com/show_bug.cgi?id=971477#c7
> 
> What does `brctl show` have on your faulty host? (just to rule out that vdsm
> is lying about the ovirtmgmt being connected to two nics)
> 
> {'ovirtmgmt': {'addr': '10.70.36.44', 'cfg': {'DELAY': '0', 'NM_CONTROLLED':
> 'no', 'BOOTPROTO': 'dhcp', 'DEVICE': 'ovirtmgmt', 'TYPE': 'Bridge',
> 'ONBOOT': 'yes'}, 'mtu': '1500', 'netmask': '255.255.254.0', 'stp': 'off',
> 'ports': ['eth0', 'eth2']}}
> 
> Does it reproduce on any other system?
> Does it go away once you manually
> 
>   brctl delif ovirtmgmt eth0
> 
_______________________________________________
vdsm-devel mailing list
vdsm-devel@lists.fedorahosted.org
https://lists.fedorahosted.org/mailman/listinfo/vdsm-devel

Reply via email to