thanks dave. yes the os does see the library as well as the drive.
SunOS truxtun 5.10 Generic_127127-11 sun4u sparc SUNW,Sun-Fire-V210
bash-3.00# /usr/openv/volmgr/bin/sgscan
/dev/sg/c0t0l0: Disk (/dev/rdsk/c1t0d0): "FUJITSU MAW3073NCSUN72G"
/dev/sg/c0t1l0: Disk (/dev/rdsk/c1t1d0): "FUJITSU MAW3073NCSUN72G"
/dev/sg/c1t0l0: Changer: "EXABYTE LTO 1x7 2U"
/dev/sg/c1t3l0: Tape (/dev/rmt/0): "HP Ultrium 3-SCSI"
bash-3.00# /usr/openv/volmgr/bin/scan
************************************************************
*********************** SDT_TAPE ************************
*********************** SDT_CHANGER ************************
*********************** SDT_OPTICAL ************************
************************************************************
------------------------------------------------------------
Device Name : "/dev/sg/c1t0l0"
Passthru Name: "/dev/sg/c1t0l0"
Volume Header: ""
Port: -1; Bus: -1; Target: -1; LUN: -1
Inquiry : "EXABYTE LTO 1x7 2U B00B"
Vendor ID : "EXABYTE "
Product ID : "LTO 1x7 2U "
Product Rev: "B00B"
Serial Number: "000087005544"
WWN : ""
WWN Id Type : 0
Device Identifier: "EXABYTE LTO 1x7 2U 000087005544"
Device Type : SDT_CHANGER
NetBackup Robot Type: 8
Removable : Yes
Device Supports: SCSI-4
Number of Drives : 1
Number of Slots : 7
Number of Media Access Ports: 0
Drive 1 Serial Number : "D217H001HU"
Flags : 0x0
Reason: 0x0
------------------------------------------------------------
Device Name : "/dev/rmt/0cbn"
Passthru Name: "/dev/sg/c1t3l0"
Volume Header: ""
Port: -1; Bus: -1; Target: -1; LUN: -1
Inquiry : "HP Ultrium 3-SCSI D217"
Vendor ID : "HP "
Product ID : "Ultrium 3-SCSI "
Product Rev: "D217"
Serial Number: "HU171200RB"
WWN : ""
WWN Id Type : 0
Device Identifier: ""
Device Type : SDT_TAPE
NetBackup Drive Type: 16
Removable : Yes
Device Supports: SCSI-3
Flags : 0x0
Reason: 0x0
bash-3.00# /usr/openv/volmgr/bin/tpconfig -l
Device Robot Drive Robot
Drive Device Second
Type Num Index Type DrNum Status Comment Name
Path Device Path
robot 0 - TLD - -
- - /dev/sg/c1t0l0
drive - 0 hcart3 - UP
- HP.ULTRIUM3-SCSI.000 /dev/rmt/0cbn
________________________________
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Cornely, David
Sent: Monday, July 14, 2008 12:32 PM
To: [email protected]
Subject: Re: [Veritas-bu] robot not enabled.
Does the OS see the robot? Check that using sgscan -- if the OS doesn't see
the changer then that's your problem.
________________________________
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Taylor, David
(MARSYS)
Sent: Monday, July 14, 2008 12:19
To: [email protected]
Subject: [Veritas-bu] robot not enabled.
good morning.
i am setting up a test disaster recovery server running netbackup 6 mp5
on a v210 with solaris 10 with a exabyte magnum 1x7 autoloader.
running the storage device wizard fails thus leaving the robot disabled
"not enabled", the lto 3 tape drive is picked up without problems.
i have tried to configure the robot manually using tpconfig but get the
some results.
any ideas?
thanks, dave..
_______________________________________________
Veritas-bu maillist - [email protected]
http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
