DAG name is set under client tab. Basically, you need to install NBU client on every node in DAG (including CAS if exist).
On Wed, Oct 13, 2010 at 5:32 PM, Jonathan Dyck <[email protected]>wrote: > Maybe I jumped the gun emailing the list. #1 was my problem. Anyone > getting into this, make sure you install the client on all servers in > the DAG and add them in the correct order in your "Preferred Server > List". > > Cheers. > > > -----Original Message----- > From: Jonathan Dyck > Sent: October 13, 2010 9:00 AM > To: [email protected] > Subject: Exchange 2010 DAG backups w/ Netbackup 7.0.1 > > Hello list, > I'm hoping someone out there has gone through the pain of trying to > setup Exchange 2010 DAG backups from the passive node. Reading through > the documentation, I'm a little unclear on a couple things. Here's the > rough outline of what I've done so far: > > ------------ > 1) Installed the standard NBU 7.0.1 windows client on the passive server > of the DAG (none of the databases are active on this server). The > client name in the NBU config is the physical name of the server, not > the DAG AD object name. > > I did not install the client on either of the two active servers in the > DAG (3 servers total, two split the active databases, the third is > completely passive). Maybe this is a problem and I should install the > client on the active servers too for my test? > > 2) Verified that my media/master server is 7.0.1 and has the correct > license for Exchange, and that it can backup regular filesystem files > off of the physical client name of that passive node (networking's all > good). > > 3) Setup an Exchange policy on the NBU, it has the following properties: > - "Perform snapshot backups" is enabled > - "Enable granular recovery" is disabled > - "Database backup source:" is set to Passive copy only > - My preferred server list has one entry, which is the physical name of > the passive node, not the DAG name. Maybe this is a problem? > - I've specified the client name in the policy selection to the DAG name > ------------ > > Can anyone out there take a second to point out any errors in the above > setup? I'm running into the Status code 26 issue (handshaking failed), > which is supposed to be resolved with 7.0.1, but there's a hotfix I seem > to be able to download. I'll be going down that road too. Hopefully > that's all I'm missing. > > Cheers, > Jon > > > > > ==================================================================================== > > La version française suit le texte anglais. > > > ------------------------------------------------------------------------------------ > > This email may contain privileged and/or confidential information, and the > Bank of > Canada does not waive any related rights. Any distribution, use, or copying > of this > email or the information it contains by other than the intended recipient > is > unauthorized. If you received this email in error please delete it > immediately from > your system and notify the sender promptly by email that you have done so. > > > ------------------------------------------------------------------------------------ > > Le présent courriel peut contenir de l'information privilégiée ou > confidentielle. > La Banque du Canada ne renonce pas aux droits qui s'y rapportent. Toute > diffusion, > utilisation ou copie de ce courriel ou des renseignements qu'il contient > par une > personne autre que le ou les destinataires désignés est interdite. Si vous > recevez > ce courriel par erreur, veuillez le supprimer immédiatement et envoyer sans > délai à > l'expéditeur un message électronique pour l'aviser que vous avez éliminé de > votre > ordinateur toute copie du courriel reçu. > _______________________________________________ > Veritas-bu maillist - [email protected] > http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu >
_______________________________________________ Veritas-bu maillist - [email protected] http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
