Hi All!
Kanotix khi ca`i le^n HDD, tu`y theo mi`nh cho.n ca`i 1 trong 3 ca'ch
(beginner, Knoppix, Debian) thi` khi boot le^n no' cho ca'c file log
kha'c nhau.
To^i kho^ng co' nghe^` ne^n post le^n dda^y dde^? ca'c ba.n xem xe't.
Mong duoc nghe ca'c lo+`i ba`n lua^.n bo^? i'ch.
m k h _ s g n
Linux version 2.6.6-kanotix-2 ([EMAIL PROTECTED]) (gcc version 3.3.4 (Debian)) #1 Fri
Jun 18 15:26:33 CEST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000017fc0000 (usable)
BIOS-e820: 0000000017fc0000 - 0000000017ff8000 (ACPI data)
BIOS-e820: 0000000017ff8000 - 0000000018000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
383MB LOWMEM available.
On node 0 totalpages: 98240
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 94144 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 AMI ) @ 0x000ff980
ACPI: RSDT (v001 D845PT BG84510A 0x20020419 MSFT 0x00001011) @ 0x17ff0000
ACPI: FADT (v001 D845PT PT84510A 0x20020419 MSFT 0x00001011) @ 0x17ff1000
ACPI: MADT (v001 D845PT PT84510A 0x20020419 MSFT 0x00001011) @ 0x17fe36fd
ACPI: DSDT (v001 D845PT PT84510A 0x00000003 MSFT 0x0100000b) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
Built 1 zonelists
Kernel command line: auto BOOT_IMAGE=Kanotix rw root=309 lang=en hdb=ide-scsi
hdc=ide-scsi hdd=ide-scsi
ide_setup: hdb=ide-scsi
ide_setup: hdc=ide-scsi
ide_setup: hdd=ide-scsi
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 1994.679 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Memory: 384876k/392960k available (2556k kernel code, 7316k reserved, 1041k data, 264k
init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3948.54 BogoMIPS
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 3febfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: 3febfbff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU#0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU: Intel(R) Pentium(R) 4 CPU 2.00GHz stepping 04
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1993.0882 MHz.
..... host bus clock speed is 99.0694 MHz.
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfda95, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: Using ACPI for IRQ routing
vesafb: framebuffer at 0xe8000000, mapped to 0xd8807000, size 16384k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:e8f0
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
Machine check exception polling timer started.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SGI XFS with ACLs, security attributes, realtime, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Console: switching to colour frame buffer device 128x48
Generic RTC Driver v1.07
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2: IDE controller at PCI slot 0000:00:1f.1
ICH2: chipset revision 5
ICH2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA
hda: SAMSUNG SP0802N, ATA DISK drive
hdb: ATAPI CD-ROM DRIVE 40X MAXIMUM, ATAPI CD/DVD-ROM drive
hdb: Disabling (U)DMA for ATAPI CD-ROM DRIVE 40X MAXIMUM (blacklisted)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: ASUS DVD-ROM E616, ATAPI CD/DVD-ROM drive
hdd: HL-DT-ST GCE-8525B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 156368016 sectors (80060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 hda9 hda10 >
ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX as device
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: ATAPI Model: CD-ROM DRIVE-40X Rev: 40CP
Type: CD-ROM ANSI SCSI revision: 02
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: ASUS Model: DVD-ROM E616 Rev: Z.0
Type: CD-ROM ANSI SCSI revision: 02
scsi2 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: HL-DT-ST Model: CD-RW GCE-8525B Rev: 1.03
Type: CD-ROM ANSI SCSI revision: 02
libata version 1.02 loaded.
sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr1: scsi3-mmc drive: 6x/48x cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr1 at scsi1, channel 0, id 0, lun 0
sr2: scsi3-mmc drive: 40x/52x writer cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr2 at scsi2, channel 0, id 0, lun 0
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 2352.000 MB/sec
8regs_prefetch: 2004.000 MB/sec
32regs : 1212.000 MB/sec
32regs_prefetch: 1260.000 MB/sec
pIII_sse : 2496.000 MB/sec
pII_mmx : 3064.000 MB/sec
p5_mmx : 3048.000 MB/sec
raid5: using function: pIII_sse (2496.000 MB/sec)
raid6: int32x1 484 MB/s
raid6: int32x2 714 MB/s
raid6: int32x4 457 MB/s
raid6: int32x8 503 MB/s
raid6: mmxx1 1574 MB/s
raid6: mmxx2 2042 MB/s
raid6: sse1x1 1050 MB/s
raid6: sse1x2 1417 MB/s
raid6: sse2x1 1757 MB/s
raid6: sse2x2 2152 MB/s
raid6: using algorithm sse2x2 (2152 MB/s)
md: raid6 personality registered as nr 8
md: multipath personality registered as nr 7
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: [EMAIL PROTECTED]
EISA: Probing bus 0 at eisa0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 1
PM: Reading pmdisk image.
PM: Resume from disk failed.
ACPI: (supports S0 S1 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
found reiserfs format "3.6" with standard journal
reiserfs: using ordered data mode
Reiserfs journal params: device hda9, size 8192, journal first block 18, max trans len
1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hda9) for (hda9)
Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem).
Freeing unused kernel memory: 264k freed
hdb: Disabling (U)DMA for ATAPI CD-ROM DRIVE 40X MAXIMUM (blacklisted)
Adding 1076312k swap on /dev/hda6. Priority:-1 extents:1
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU1] (supports C1)
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:1f.2: Intel Corp. 82801BA/BAM USB (Hub #1)
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: irq 11, io base 0000ef40
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:1f.4: Intel Corp. 82801BA/BAM USB (Hub #2)
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: irq 10, io base 0000ef80
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ieee1394: Initialized config rom entry `ip1394'
usb 2-2: new full speed USB device using address 2
hub 2-2:1.0: USB hub found
hub 2-2:1.0: 4 ports detected
Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 5
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 5
Attached scsi generic sg2 at scsi2, channel 0, id 0, lun 0, type 5
hw_random hardware driver 1.0.0 loaded
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel i845 Chipset.
agpgart: Maximum main memory to use for agp memory: 321M
agpgart: AGP aperture is 64M @ 0xf8000000
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hda10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49483 usecs
intel8x0: clocking to 48000
apm: BIOS not found.
mtrr: 0xe8000000,0x4000000 overlaps existing 0xe8000000,0x1000000
NET: Registered protocol family 4
NET: Registered protocol family 3
NET: Registered protocol family 5
Linux version 2.6.6-kanotix-2 ([EMAIL PROTECTED]) (gcc version 3.3.4 (Debian)) #1 Fri
Jun 18 15:26:33 CEST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000017fc0000 (usable)
BIOS-e820: 0000000017fc0000 - 0000000017ff8000 (ACPI data)
BIOS-e820: 0000000017ff8000 - 0000000018000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
383MB LOWMEM available.
On node 0 totalpages: 98240
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 94144 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 AMI ) @ 0x000ff980
ACPI: RSDT (v001 D845PT BG84510A 0x20020419 MSFT 0x00001011) @ 0x17ff0000
ACPI: FADT (v001 D845PT PT84510A 0x20020419 MSFT 0x00001011) @ 0x17ff1000
ACPI: MADT (v001 D845PT PT84510A 0x20020419 MSFT 0x00001011) @ 0x17fe36fd
ACPI: DSDT (v001 D845PT PT84510A 0x00000003 MSFT 0x0100000b) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
Built 1 zonelists
Kernel command line: root=/dev/hda8 ro ramdisk_size=100000 lang=de apm=power-off
hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi nomce vga=791
ide_setup: hda=scsi
ide_setup: hdb=scsi
ide_setup: hdc=scsi
ide_setup: hdd=scsi
ide_setup: hde=scsi
ide_setup: hdf=scsi
ide_setup: hdg=scsi
ide_setup: hdh=scsi
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 1995.037 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Memory: 384876k/392960k available (2556k kernel code, 7316k reserved, 1041k data, 264k
init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3948.54 BogoMIPS
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 3febfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: 3febfbff 00000000 00000000 00000080
CPU: Intel(R) Pentium(R) 4 CPU 2.00GHz stepping 04
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1993.0854 MHz.
..... host bus clock speed is 99.0692 MHz.
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfda95, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: Using ACPI for IRQ routing
vesafb: framebuffer at 0xe8000000, mapped to 0xd8807000, size 16384k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:e8f0
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
Machine check exception polling timer started.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SGI XFS with ACLs, security attributes, realtime, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Console: switching to colour frame buffer device 128x48
Generic RTC Driver v1.07
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2: IDE controller at PCI slot 0000:00:1f.1
ICH2: chipset revision 5
ICH2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA
hda: SAMSUNG SP0802N, ATA DISK drive
hdb: ATAPI CD-ROM DRIVE 40X MAXIMUM, ATAPI CD/DVD-ROM drive
hdb: Disabling (U)DMA for ATAPI CD-ROM DRIVE 40X MAXIMUM (blacklisted)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: ASUS DVD-ROM E616, ATAPI CD/DVD-ROM drive
hdd: HL-DT-ST GCE-8525B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 156368016 sectors (80060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 hda9 hda10 >
ide-cd: passing drive hdb to ide-scsi emulation.
ide-cd: passing drive hdc to ide-scsi emulation.
ide-cd: passing drive hdd to ide-scsi emulation.
ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX as device
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: ATAPI Model: CD-ROM DRIVE-40X Rev: 40CP
Type: CD-ROM ANSI SCSI revision: 02
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: ASUS Model: DVD-ROM E616 Rev: Z.0
Type: CD-ROM ANSI SCSI revision: 02
scsi2 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: HL-DT-ST Model: CD-RW GCE-8525B Rev: 1.03
Type: CD-ROM ANSI SCSI revision: 02
libata version 1.02 loaded.
sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr1: scsi3-mmc drive: 6x/48x cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr1 at scsi1, channel 0, id 0, lun 0
sr2: scsi3-mmc drive: 40x/52x writer cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr2 at scsi2, channel 0, id 0, lun 0
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 2352.000 MB/sec
8regs_prefetch: 2024.000 MB/sec
32regs : 1212.000 MB/sec
32regs_prefetch: 1240.000 MB/sec
pIII_sse : 2492.000 MB/sec
pII_mmx : 3064.000 MB/sec
p5_mmx : 3048.000 MB/sec
raid5: using function: pIII_sse (2492.000 MB/sec)
raid6: int32x1 531 MB/s
raid6: int32x2 710 MB/s
raid6: int32x4 453 MB/s
raid6: int32x8 488 MB/s
raid6: mmxx1 1621 MB/s
raid6: mmxx2 2042 MB/s
raid6: sse1x1 1023 MB/s
raid6: sse1x2 1460 MB/s
raid6: sse2x1 1738 MB/s
raid6: sse2x2 2089 MB/s
raid6: using algorithm sse2x2 (2089 MB/s)
md: raid6 personality registered as nr 8
md: multipath personality registered as nr 7
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: [EMAIL PROTECTED]
EISA: Probing bus 0 at eisa0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 1
PM: Reading pmdisk image.
PM: Resume from disk failed.
ACPI: (supports S0 S1 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
found reiserfs format "3.6" with standard journal
reiserfs: using ordered data mode
Reiserfs journal params: device hda8, size 8192, journal first block 18, max trans len
1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hda8) for (hda8)
Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 264k freed
hdb: Disabling (U)DMA for ATAPI CD-ROM DRIVE 40X MAXIMUM (blacklisted)
Adding 1076312k swap on /dev/hda6. Priority:-1 extents:1
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU1] (supports C1)
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:1f.2: Intel Corp. 82801BA/BAM USB (Hub #1)
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: irq 11, io base 0000ef40
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:1f.4: Intel Corp. 82801BA/BAM USB (Hub #2)
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: irq 10, io base 0000ef80
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ieee1394: Initialized config rom entry `ip1394'
Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
usb 2-2: new full speed USB device using address 2
hub 2-2:1.0: USB hub found
hub 2-2:1.0: 4 ports detected
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 5
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 5
Attached scsi generic sg2 at scsi2, channel 0, id 0, lun 0, type 5
hw_random hardware driver 1.0.0 loaded
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel i845 Chipset.
agpgart: Maximum main memory to use for agp memory: 321M
agpgart: AGP aperture is 64M @ 0xf8000000
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
found reiserfs format "3.6" with standard journal
reiserfs: using ordered data mode
Reiserfs journal params: device hda9, size 8192, journal first block 18, max trans len
1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hda9) for (hda9)
Using r5 hash to sort names
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hda10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ts: Compaq touchscreen protocol output
blk: queue d7d4cc00, I/O limit 4095Mb (mask 0xffffffff)
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49486 usecs
intel8x0: clocking to 48000
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
apm: BIOS not found.
