On my both my zVM 4.4 & 5.2 systems if I use PARM INSTSEG on the IPL command the message tells me the name of the segment that could not be loaded, such as:
i cms parm instseg bhn DMSWSP327I The installation saved segment BHN could not be loaded or: i cms parm instseg DMSWSP327W INSTSEG value omitted; no shared EXECs loaded Is the message you posted a cut & paste or a retype that might have the segment name omiited? Brian Nielsen On Mon, 23 Jan 2006 14:00:48 -0000, Dusha, Cecelia, Ms., WHS/ITMD <[EMAIL PROTECTED]> wrote: >The problem I am experiencing on my zVM 5.1 system is described below. > > > >ipl cms > >DMSWSP327I The installation saved segment could not be loaded > > > >MSG DMSWSP327I All Help Information line 1 of >27 > >(c) Copyright IBM Corporation 1990, 2004 > > > > > > DMS327I The <installation|multitasking> saved segment segname could not >be > > loaded > > > > > > System Programmer Response: If the INSTSEG or MTSEG parameter was used on >the > > IPL command, verify it is the correct name of a CMS Installation or > > > Multitasking Saved Segment. If the INSTSEG or MTSEG parameter was not used >on > > the IPL command, verify the correct name for the Installation or >Multitasking > > Saved Segment was specified in DMSNGP or in response to the Installation or > > > Multitasking Saved Segment name prompt when the CMS nucleus was generated. >In > > either case, if the correct name was specified, verify the Installation or > > > Multitasking Saved Segment has not been purged. > > > > >The only updates to zVM 5.1 DMSNGP ASSEMBLE is to change the CMS IPL area on >MAINT's 190 disk. > >My zVM 3.1 system does not have any additional changes, but the above >message does not appear when CMS is IPLed. > >DMSNGP ASSEMBLE F1 F 80 Trunc=71 Size=122 Line=113 Col=1 Alt=0 > > > > > >00113 INSTSEG=CMSINST, * Name of above saved segment >* > >00114 USEMTSG=YES, *** See Operation section >@SE062PQ* > >00115 MTSEG=VMMTLIB, *** See Operation section >@SE062PQ* > > > >zVM 5.1: > >q nss name cmsinst > >FILES: NO NSS > >Ready; T=0.01/0.01 08:47:01 > >q nss name instseg > >OWNERID FILE TYPE CL RECS DATE TIME FILENAME FILETYPE ORIGINID > >*NSS 0026 NSS A 0770 12/15 11:13:27 INSTSEG DCSS MAINT > >Ready; T=0.01/0.01 08:47:11 > >q nss name mtseg > >FILES: NO NSS > >Ready; T=0.01/0.01 08:47:21 > >q nss name vmmtlib > >FILES: NO NSS > >Ready; T=0.01/0.01 08:47:32 > > > >I get the same results from the above queries on my zVM 3.1 system, but the >message does not appear when CMS is IPLed. > > > >The zVM 5.1 Service Guide on page 3-69 says: > >11. Build the CMSINST logical saved segment. > > Vmfbld ppf segbld esasegs segblist instseg (serviced > >This step generates the INSTSEG segment... > > > >The message says, "If the INSTSEG or MTSEG parameter was not used on the IPL >command, verify the correct name for the Installation or Multitasking Saved >Segment was specified in DMSNGP or in response to the Installation or >Multitasking Saved Segment name prompt when the CMS nucleus was generated." > > > >Do I need to perform a detailed build of CMS to get CMS to recognize the >INSTSEG segment? > > > >Please advice. > > > >Thank you. > > > >Cecelia Dusha >=========================================================================
