Todd, I have version 1.01. Yes, please e-mail me your modified version. Maybe it will help.
Thanks, Randy On Sat, Dec 30, 2017 at 4:24 AM, Todd Micallef <tmical...@gmail.com> wrote: > Randy, > > Is there a version number at the top of the file? I had two versions (1.00 > and 1.01). I can't remember all that changed between the two since it has > been a while but I did find an additional timeout code that limited the > wait time for reading data to 1 minute. I am guessing I had a problem with > mine and added it. > > I can email it to you if you want to try it. If it works for you, I will > have Illya update it on xDevs. > > Todd > > On Sat, Dec 30, 2017 at 12:39 AM, Randy Evans <randyevans2...@gmail.com> > wrote: > > > I am still unable to get my HP-3458A to work with the xdevs program > > "HP3458A_Measure_DMM_Noise.488" (https://xdevs.com/article/dmm_noise/). > > It > > works fine with my Agilent 3458A and with a friend's HP-3458A and his > > Agilent 3458A using the EZGPIB program. The SW versions are identical > with > > my friend's DMMs, the HP units are (8.2) and with the Agilent units are > > (9.2). However, both of my units work fine with the KE5FX GPIB Toolkit > > HP3458.EXE program to download the NVRAM CAL data. This would seem to > > indicate that my HP-3458 GPIB works at least partially. > > > > Does anyone have a EZGPIB program that I could try to run (that is > > different from the Xdev program)? It would be nice to see if I could get > > something to work other than the HP3458.EXE program. Or if any one has > > some ideas on what to look for. > > > > Thanks, > > > > Randy Evans > > > > On Tue, Dec 26, 2017 at 7:24 PM, Randy Evans <randyevans2...@gmail.com> > > wrote: > > > > > I am hoping some of you experts might be able to assist with a strange > > > problem i am having trying to make automated measurements using EZGPIB > > with > > > an Agilent and an HP 3458A. I have a program given to me by Martin > > > Reynolds, which is a variant on the Xdevs noise measurement program. > > > Martin's program continuously reads the voltage measurements > sequentially > > > from the two meters and then stores then in a measurements file, along > > with > > > the temperature measurements from both meters. The program works fine > on > > > his Agilent and HP 3458As. > > > > > > On my two 3458As, it takes the temperature measurements just fine but > > only > > > takes a voltage measurement from the Agilent unit. The HP unit will > not > > > make any voltage measurements although I can see both the 3458As in > talk > > > states and, of course, it does sent the temperature measurements. > > However, > > > if I turn the HP unit off and then on again, the HP will start to take > > > voltage and temperature measurements and send them to the PC. > > > > > > Any ideas on what might be causing the strange behavior? > > > > > > Thanks, > > > > > > Randy Evans > > > > > _______________________________________________ > > volt-nuts mailing list -- volt-nuts@febo.com > > To unsubscribe, go to https://www.febo.com/cgi-bin/ > > mailman/listinfo/volt-nuts > > and follow the instructions there. > > > _______________________________________________ > volt-nuts mailing list -- volt-nuts@febo.com > To unsubscribe, go to https://www.febo.com/cgi-bin/ > mailman/listinfo/volt-nuts > and follow the instructions there. > _______________________________________________ volt-nuts mailing list -- volt-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/volt-nuts and follow the instructions there.