An excerpt from the Lugano report:

"A thermocouple probe, inserted into one of the caps, allows the control
system to manage power supply to the resistors by measuring the internal
temperature of the reactor. The hole for the thermocouple probe is also the
only access point for the fuel charge. The thermocouple probe cable is
inserted in an alumina cement cylinder, which acts as a bushing and
perfectly fits the hole, about 4 mm in diameter. When charging the reactor,
the bushing is pulled out, and the charge is inserted. After the
thermocouple probe has been lodged back in place, the bushing is sealed and
secured with alumina cement. To extract the charge, pliers are used to open
the seal."

The alumina to metal sealing technique that Rossi uses is both elegant and
simple. Rossi's alumina core tube has a hole at its end that is just a
little bit wider than the metal plug used to fill it. After Rossi fills the
alumina tube with fuel, there is a slight space (say ten thousandth of a
inch)between the metal plug and the hole in the alumina body(5.4). The
space will be coated with fuel which includes aluminum(22), lithium(46),
and nickel(13).

The numbers in parentheses are the thermal coefficients of expansion of of
the various materials in the alumina and the fuel found in this table as
follows”

http://www.engineeringtoolbox.com/linear-expansion-coefficients-d_95.html

A hole sealing process will occur to thermally bond the metal plug to the
hole in the alumina when heated as follows:

As the alumina heats up, the fuel residue coating will form a tight fitting
metalized gadget between the metal plug and alumina hole. The fuel will
liquefy and form a aluminum nickel lithium alloy and fill the micro-cracks
on the surface of the hole and the metal plug. The metal plug will be
pressure welded into the hole because of the differences in the thermal
coefficients of expansion between the various metals ad the alumina to form
a leak proof seal that will stand up to very high gas pressure,
These recent tests by MFMP indicate that sealing alumina from hydrogen
leakage is a challenge. But the Rossi Hot Cat did run for weeks without
apparent loss of hydrogen. Rossi has come up with a way to effectively seal
alumina.

How could have Rossi made the alumina tube resistant to hydrogen leakage?

Could Rossi have used a self sealing fuel additive included in the fuel mix
that entered the pores of the alumina after the reactor was started to
minimize hydrogen exfiltration?

There was a large amount of carbon in the element analysis of the fuel
load. Could it be that Rossi used a organic sealant to stop hydrogen
leakage?

An excerpt from the Lugano report:"Sample 2 was the fuel used to charge the
E-Cat. It’s in the form of a very fine powder. Besides the analyzed
elements it has been found that the fuel also contains rather high
concentrations of C, Ca, Cl, Fe, Mg, Mn and these are not found in the ash.

Where did all those rather high concentrations of elements go? Could it be
that the C, Ca, Cl, Fe, Mg, and Mn were nano particles used to seal the
fuel including hydrogen by blocking the pores of the alumina in a self
anodizing process in the initial stages during reactor startup? Carbon is a
well know hydrogen blocker.




On Thu, Jan 15, 2015 at 9:57 PM, Jack Cole <[email protected]> wrote:

> The description in the report is insufficient to determine what was used
> to make the seal and whether it was hermetically sealed.
> On Jan 15, 2015 8:53 PM, "Axil Axil" <[email protected]> wrote:
>
>> It does work, It worked for Rossi for 32 days.
>>
>> On Thu, Jan 15, 2015 at 5:23 PM, Jack Cole <[email protected]> wrote:
>>
>>> It might work.  I have been looking at those options (i.e., metal
>>> compression fitting).
>>>
>>> On Thu, Jan 15, 2015 at 4:02 PM, Axil Axil <[email protected]> wrote:
>>>
>>>> Like Rossi did, MFMP has just tested and intends to use in their next
>>>> experiment  a metal plug or a thermocouple probe  to seal the fuel feed
>>>> hole in the alumina rod.
>>>>
>>>> Why is this sealing process not right for you?
>>>>
>>>> On Thu, Jan 15, 2015 at 4:53 PM, Jack Cole <[email protected]> wrote:
>>>>
>>>>> Yes, it bolsters the results of the first experiment by demonstrating
>>>>> that reliability.
>>>>>
>>>>> On Thu, Jan 15, 2015 at 2:54 PM, Jed Rothwell <[email protected]>
>>>>> wrote:
>>>>>
>>>>>> I wrote:
>>>>>>
>>>>>>
>>>>>>> Well, it is a nice clean blank anyway. The two sets of points fit on
>>>>>>> top of one-another beautiful.
>>>>>>>
>>>>>>
>>>>>> Meaning the instrument is reliable as a calorimeter. This is
>>>>>> important.
>>>>>>
>>>>>> - Jed
>>>>>>
>>>>>>
>>>>>
>>>>
>>>
>>

Reply via email to