Sorry, forgot to mention that I did build my kernel using the voyage kernel-source-2-6-14 ...and the config-2.6.14-486-voyage_2.0-6 file.
That instruction does not work and I think I have found out why, correct me if I am wrong. When I configured the kernel source, the default settings according to the .config-file was to build support for the Atheros-PCI into the kernel, not as a module. I guess this means that I cannot load/unload the ath_pci module dynamically? And that is why the ath_pci is missing in the /lib/modules/uname -r/modules.pcimap.
I will build a new kernel with Atheros-PCI support built as a module and try if it works.
Finally I would like to say thanks for a nice distro and the work you put down sustaining and developing it.
/Nicklas
On 1/11/06, Punky Tse <[EMAIL PROTECTED]> wrote:
Nicklas,
Do you build your own kernel or using the standard voyage kernel? Looks
like you are building the kernel.
Doesn't the following instruction work for you?
http://wiki.voyage.hk/dokuwiki/doku.php?id=how_to_set_country_code_for_madwifi_device
If you need some kernel features that is yet in standard voyage kernel,
please send your request to this list. If it is not too hard, I will
probably include it in later release.
Punky
Nicklas Blidmo wrote:
> After upgrading to a new kernel I'm not able to do a modprobe ath_pci
> anymore, even though this driver is successfully loaded at boot time.
> I have understood that this is because ath_pci is missing in
> /lib/modules/2.6.14_my_kernel/modules.pcimap. it is present in
> 2.6.8-486-voyage/modules.pcimap.
>
> Have I missed something when upgrading the kernel?
> I need to fix this to be able to change country code.
>
> Thanks in advance
>
> Nicklas Blidmo
>
> ****** boot messages below ****
>
> ath_hal: 0.9.14.9 <http://0.9.14.9> (AR5210, AR5211, AR5212, RF5111,
> RF5112,
> RF2413)
> ath_rate_sample: 1.2
> ath_pci: 0.9.6.0 < http://0.9.6.0>
> (EXPERIMENTAL)
> Build date: Dec
> Debugging version (IEEE80211)
> ath0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps
> 54Mbps
>
> ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps
> 11Mbps
> ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps
> 24Mbps
> 36M
>
> bps 48Mbps 54Mbps
> ath0: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps
> 54Mbps
>
> ath0: turboG rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps
> 54Mbps
>
> ath0: H/W encryption support: WEP AES AES_CCM
> TKIP
> ath0: mac 5.9 phy 4.3 radio 3.6
> ath0: Use hw queue 1 for WME_AC_BE
> traffic
> ath0: Use hw queue 0 for WME_AC_BK
> traffic
> ath0: Use hw queue 2 for WME_AC_VI
> traffic
> ath0: Use hw queue 3 for WME_AC_VO
> traffic
> ath0: Use hw queue 8 for CAB traffic
> ath0: Use hw queue 9 for beacons
> Debugging version (ATH)
> ath0: Atheros 5212: mem=0x80080000,
> irq=9
> wlan: 0.8.6.0 <http://0.8.6.0> (EXPERIMENTAL)
> wlan: mac acl policy registered
>
>------------------------------------------------------------------------
>
>_______________________________________________
>Voyage-linux mailing list
>[email protected]
>http://list.voyage.hk/mailman/listinfo/voyage-linux
>
>
--
Regards,
Punky
P U N K N ! X . c o m
Technology + Lifestyle
(http://www.punknix.com)
Voyage Linux
( http://www.voyage.hk/software/voyage.html)
_______________________________________________ Voyage-linux mailing list [email protected] http://list.voyage.hk/mailman/listinfo/voyage-linux
