have you tried giving the clients behind the bridge fixed IP addresses? does traffic pass? have you also tried unencrypted wlan?
2016-10-05 9:20 GMT+02:00 tux john <a...@null.net>: > Thanks a lot for the quick reply. the post you send, it is currently the > one that i am using. The problem is that it does not allow traffic in > between the eth0 and wlan0 unless it is NAT involved. > wlan0 is in 172.16.8.1/24 and serves IPs from dhcp. i do need to share > the wifi internet connection to a switch attached to the eth0, without NAT. > I would like all devices attached to eth0 to get an IP from the dhcp > server of the wlan0. how can i change the config to make it work? > > > *Sent:* Tuesday, October 04, 2016 at 8:17 PM > *From:* "Bánhidi István" <banhidi.ist...@gmail.com> > *To:* "tux john" <a...@null.net>, "voyage_linux list" < > voyage-li...@voyage.hk> > *Subject:* Re: [Voyage-linux] bridge wlan0 to eth0 > Hi, > > I don't understand exactly what you want, but i hope this help (source > from voyage wiki): > > ====== Build a Bridge with Voyage ====== > I used voyage-0.2pre1 on a WRAP 2C. The bridged devices are a Prism > wireless mini-PCI card and the WRAP's built in ethernet port. > Edit the /etc/network/interfaces > > Mine looks like this: > > auto br0 > iface br0 inet static > address 192.168.254.253 > netmask 255.255.255.0 > network 192.168.254.0 > broadcast 192.168.1.255 > gateway 192.168.254.1 > bridge_ports eth0 wlan0 > pre-up iwconfig wlan0 essid testing mode master > > The first 5 lines set up the bridged IP infomation. The next line > configures the bridge itself. The only line that you will really need to > change is the line that starts with "pre-up iwconfig...". This configures > the the wireless card to be an access point and sets the ssid to "testing". > The final lines that start with post-down enable the bridge to be shutdown > nicely. > > Once you get everything configured to your liking, restart your network > and test connectivity. > > > > Good luck > Steve > > 2016.10.04. 8:18 keltezéssel, tux john írta: > > Hi. i have an alix 2d13 (pcengines) that has 3 ethernet ports . I would > like to create a failover setup. > > I have a nearby community wifi that i connect to with the following: > > auto wlan0 > iface wlan0 inet dhcp > wpa-ssid "Community_wifi" > wpa-psk "xyzPasSwd" > up nat.sh eth1 wlan0 "192.168.179.0/24" > dns-nameservers 8.8.8.8 > > auto eth1 > iface eth1 inet static > address 192.168.179.1 > netmask 255.255.255.0 > > by doing that i get all the traffic nated to eth1/wlan0. > > i have tried to create a br0 interface with wlan0 and eth0 but it does > allow traffic in between, unless i do a nat. > > I would like to *NOT do a NAT* setup. All devices attached to eth1 to get > an IP from the pool of the community wifi. how can i change my setup to > be able to have an IP on eth1 from the community wifi dhcp, as well all > computers attached to eth1 to get an IP from the same pool, please? > > > > > > _______________________________________________ > Voyage-linux mailing > listVoyage-linux@list.voyage.hkhttp://list.voyage.hk/mailman/listinfo/voyage-linux > > > _______________________________________________ > Voyage-linux mailing list > Voyage-linux@list.voyage.hk > http://list.voyage.hk/mailman/listinfo/voyage-linux > >
_______________________________________________ Voyage-linux mailing list Voyage-linux@list.voyage.hk http://list.voyage.hk/mailman/listinfo/voyage-linux
