On 04/18/2013 03:04 AM, eric xu wrote:
Hi All,
As a new user I run into problem as described briefly in caption. More details
is as follows:
- Shrew Version: 2.17 complied on Ubuntu 12.04.2 LTS 32-bit (IBM T41)
- Gateway: Juniper SSG20 Version: 6.2.0r5.0 (Firewall+VPN)
- qikea shows "Established"
- tap0 created but can ping nowhere into the private network (192.168.11.0/24)
Ifconfig:
eth0 Link encap:Ethernet HWaddr 00:0d:60:b2:ac:27
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth1 Link encap:Ethernet HWaddr 00:0c:f1:40:6e:73
inet addr:117.128.171.xxx Bcast:117.128.171.63 Mask:255.255.255.192
inet6 addr: fe80::20c:f1ff:fe40:6e73/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:79181 errors:0 dropped:0 overruns:0 frame:0
TX packets:69530 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:91427974 (91.4 MB) TX bytes:6226954 (6.2 MB)
Interrupt:11 Base address:0x8000 Memory:c0214000-c0214fff
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1708 errors:0 dropped:0 overruns:0 frame:0
TX packets:1708 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:275161 (275.1 KB) TX bytes:275161 (275.1 KB)
tap0 Link encap:Ethernet HWaddr e6:00:e5:3d:d4:17
inet addr:192.168.11.25 Bcast:192.168.11.25 Mask:255.255.255.255
inet6 addr: fe80::e400:e5ff:fe3d:d417/64 Scope:Link
UP BROADCAST RUNNING MTU:1380 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:500
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
route:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
default 117.128.171.1 0.0.0.0 UG 0 0 0 eth1
117.128.171.0 * 255.255.255.192 U 2 0 0 eth1
120.72.49.xxx 117.128.171.1 255.255.255.255 UGH 0 0 0 eth1
link-local * 255.255.0.0 U 1000 0 0 eth1
192.168.11.0 192.168.11.25 255.255.255.0 UG 0 0 0 tap0
Hi Eric,
Can you generate a log trace for us using the instructions below?
Please make sure the log_level is at debug.
https://www.shrew.net/support/VPN_Bug_Report_Unix
_______________________________________________
vpn-help mailing list
[email protected]
https://lists.shrew.net/mailman/listinfo/vpn-help
