Hi Miguel, Most your time is being spent in dpdk_input and vhost_user_input. Are you running VPP in a VM or on the host? I ask because vhost_user_input suggests you are running on the host?
If you are running in a VM and you are using software interfaces (no PCI passhrough) you might try using vpp-lite with the af_packet interface instead of dpdk_input as you will likely get similar performance without DPDK polling.
Ray K On 18/10/2016 14:53, Miguel Angel Muñoz Gonzalez wrote:
Thanks Ray. Yes, in startup.conf I set: dpdk { dev 0000:00:08.0 uio-driver uio_pci_generic } And this is the output of 'show run' though to be honest I'm not very familiar with it yet: Time 228.9, average vectors/node 1.19, last 128 main loops 0.00 per node 0.00 vector rates in 4.4491e1, out 3.9918e0, drop 4.3451e1, punt 1.0394e0 Name State Calls Vectors Suspends Clocks Vectors/Call GigabitEthernet0/8/0-output active 914 914 0 1.70e3 1.00 GigabitEthernet0/8/0-tx active 914 914 0 6.58e4 1.00 admin-up-down-process event wait 0 0 1 1.32e4 0.00 api-rx-from-ring active 0 0 1445 1.59e5 0.00 arp-input active 1147 1224 0 2.03e4 1.07 cdp-process any wait 0 0 134 2.37e3 0.00 dhcp-client-process any wait 0 0 3 6.04e3 0.00 dpdk-input polling 524816917 10187 0 8.11e6 0.00 dpdk-process any wait 0 0 76 1.53e6 0.00 error-drop active 8138 9949 0 2.42e3 1.22 error-punt active 238 238 0 8.85e3 1.00 ethernet-input active 8289 10187 0 5.47e3 1.23 flow-report-process any wait 0 0 1 6.45e3 0.00 gmon-process time wait 0 0 46 1.43e7 0.00 icmp6-neighbor-solicitation active 107 123 0 4.26e3 1.15 ip4-arp active 946 971 0 1.03e4 1.03 ip4-input active 5818 7181 0 3.24e3 1.23 ip4-lookup active 1229 1401 0 4.53e3 1.14 ip4-lookup-multicast active 4601 5760 0 5.57e3 1.25 ip4-miss active 4948 6190 0 2.11e3 1.25 ip6-hop-by-hop active 137 147 0 2.26e3 1.07 ip6-icmp-input active 107 123 0 1.45e3 1.15 ip6-icmp-neighbor-discovery-ev any wait 0 0 226 8.55e3 0.00 ip6-input active 1437 1544 0 3.88e3 1.07 ip6-local active 244 270 0 2.81e3 1.11 ip6-lookup active 1437 1544 0 4.71e3 1.07 ip6-miss active 1202 1274 0 4.16e3 1.06 lisp-retry-service any wait 0 0 113 9.63e3 0.00 startup-config-process done 1 0 1 1.56e4 0.00 unix-epoll-input polling 524526101 0 0 8.25e2 0.00 vhost-user-input polling 500057376 0 0 1.43e2 0.00 vhost-user-process any wait 0 0 69 1.31e4 0.00 vpe-link-state-process event wait 0 0 3 1.14e4 0.00 vpe-oam-process any wait 0 0 111 1.09e4 0.00 vpe-route-resolver-process any wait 0 0 3 1.19e4 0.00 Thank you very much!! Best Regards, Miguel Ángel. -----Original Message----- From: Kinsella, Ray [mailto:[email protected]] Sent: martes, 18 de octubre de 2016 15:29 To: Miguel Angel Muñoz Gonzalez <[email protected]>; [email protected] Subject: Re: [vpp-dev] Vpp_main running at 100% CPU Hi Miguel, If you are using DPDK - it would be my expectation yes. Can you do a 'show run' in vppctl to see where time is being spent. Ray K On 18/10/2016 09:02, Miguel Angel Muñoz Gonzalez wrote:Hi, In SFC project from ODL we are trying to use VPP to run a simple scenario with basic service chain setup. At the moment I'm running vpp 1609 with honeycomb in Centos7, as a VirtualBox VM. Once VPP is started, 'top' command shows vpp_main process taking 100% CPU in one of the cores and never goes down. Is this normal? I have VT-x/AMD-V/PAE/NX extensions activated. Thank you, Best Regards, Miguel Ángel. [root@localhost vagrant]# top -b -n1 top - 07:52:02 up 2:16, 4 users, load average: 1.16, 1.25, 1.31 Tasks: 197 total, 3 running, 194 sleeping, 0 stopped, 0 zombie %Cpu(s): 21.7 us, 17.5 sy, 0.0 ni, 60.6 id, 0.1 wa, 0.0 hi, 0.1 si, 0.0 st KiB Mem : 10163584 total, 2786344 free, 4864612 used, 2512628 buff/cache KiB Swap: 1572860 total, 1572860 free, 0 used. 4967176 avail Mem PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 8033 root 20 0 1933980 30820 4952 R 100.0 0.3 89:25.57 vpp_main 1 root 20 0 126600 7424 2628 S 0.0 0.1 0:01.75 systemd 2 root 20 0 0 0 0 S 0.0 0.0 0:00.00 kthreadd 3 root 20 0 0 0 0 S 0.0 0.0 0:00.18 ksoftirqd/0 5 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 kworker/0:0H 6 root 20 0 0 0 0 S 0.0 0.0 0:00.68 kworker/u4:0 7 root rt 0 0 0 0 S 0.0 0.0 0:00.07 migration/0 _______________________________________________ vpp-dev mailing list [email protected] https://lists.fd.io/mailman/listinfo/vpp-dev
_______________________________________________ vpp-dev mailing list [email protected] https://lists.fd.io/mailman/listinfo/vpp-dev
