Hello,
I am sorry i have another question.
This time not a stupid one (i hope)
I don't find the dhcp exclude command too.
This time i am looking at the right place, i am at the dhcp subnet level and
cannot
see the set exclude command. i can see everything like
domain-name,start,default-router but not exclude
second thing when i just confiugure the dhcp shared-network-name and the
subnet,i have the following thing:
not configured to listen on any interfaces!
Did i miss something,
i could try to play on the Debian and add
DHCPDARGS=eth0
to the dhcp.conf file but i think this is not a solution
Thanks again
TRoopy
---------- Original Message ----------------------------------
From: "Troopy ." <[EMAIL PROTECTED]>
Reply-To: <[EMAIL PROTECTED]>
Date: Tue, 4 Sep 2007 08:33:42 +0200
>
>Thanks very much
>
>We though that "set start" and "set stop" were at the same config level.
>
>THANKS again
>
>TRoopy
>
>
>---------- Original Message ----------------------------------
>From: "Marat Nepomnyashy" <[EMAIL PROTECTED]>
>Date: Mon, 3 Sep 2007 21:26:47 -0700
>
>>
>>Hello Troopy,
>>
>>The DHCP range stop address is specified under the DHCP range start address.
>>
>>Here's an example of a command to set the start and stop IPs of the DHCP
>>range leased out on shared network named "dhcp1":
>>
>>'set service dhcp-server shared-network-name dhcp1 subnet 192.168.2.0/24
>>start 192.168.2.100 stop 192.168.2.200'
>>
>>
>>If you do a 'show service dhcp-server', this is what the output would be:
>>
>>[EMAIL PROTECTED] show service dhcp-server
>>> shared-network-name dhcp1 {
>>> subnet 192.168.2.0/24 {
>>> start 192.168.2.100 {
>>> stop: 192.168.2.200
>>> }
>>> }
>>> }
>>
>>
>>
>>Hope this works, let me know if you have any more problems.
>>
>>-- Marat
>>
>>----- Original Message -----
>>From: "Troopy ." <[EMAIL PROTECTED]>
>>To: <vyatta-users@mailman.vyatta.com>
>>Sent: Monday, September 03, 2007 2:53 AM
>>Subject: [Vyatta-users] DHCP settings
>>
>>
>>
>>
>>Hello,
>>
>>We are trying VC2.2 with DHCP settings.
>>
>>We can use set start "ip_address" but not set stop "ip_address", the command
>>is not recognized. (!)
>>
>>When we try to commit with only set start "ip_address", vyatta complains
>>that set stop is not configured ....
>>
>>
>>
>>Thanks
>>
>>The Openmaniak Team, http://www.openmaniak.com
>>
>>We will try to release new tutorials on
>>- DHCP (VC2 was bugged)
>>- BGP (VC2 was bugged)
>>- VRRP authentification (VC2 was bugged)
>>- IPSec (new vc2.2 functionnality)
>>
>>
>>______________________________________________________
>>Désirez vous une adresse éléctronique @suisse.com?
>>Visitez la Suisse virtuelle sur http://www.suisse.com
>>
>>
>>
>>
>>
>>______________________________________________________
>>Désirez vous une adresse éléctronique @suisse.com?
>>Visitez la Suisse virtuelle sur http://www.suisse.com
>>
>>_______________________________________________
>>Vyatta-users mailing list
>>Vyatta-users@mailman.vyatta.com
>>http://mailman.vyatta.com/mailman/listinfo/vyatta-users
>>
>>
>
>
>
>______________________________________________________
>Désirez vous une adresse éléctronique @suisse.com?
>Visitez la Suisse virtuelle sur http://www.suisse.com
>
>
______________________________________________________
Désirez vous une adresse éléctronique @suisse.com?
Visitez la Suisse virtuelle sur http://www.suisse.com
_______________________________________________
Vyatta-users mailing list
Vyatta-users@mailman.vyatta.com
http://mailman.vyatta.com/mailman/listinfo/vyatta-users
