Daren, The following repository config works fine for me using livecd vc2-2:
system { package { repository community { component: "main" url: "http://archive.vyatta.com/vyatta" } repository etch { component: "main" url: "http://http.us.debian.org/debian" } } } from rootsh, apt-get update && apt-get install mdadm Daren Tay wrote: > Hi guys, need to revisit this issue again > > I've tried to get mdadm using "apt-get" but it gave me errors... when I boot > from LiveCD. > In fact, so far I've not been able to update using the default Vyatta > repository for apt-get. I had to add the other line to get what I need: > > in /etc/apt/sources.list > ------------------------ > deb http://ftp.de.debian.org/debian etch main > > Is that normal? Should that be the case, since this seems to be pointing to > default debian packages.. may or may not be suitable for Vyatta? > > On the matter, is there anyone who did RAID 1 setup for their Vyatta router? > Should I just use 2 partition, a 10MB one (config) and a 450MB (main > partition)? > > What are your recommended partitions? > > Thanks! > Daren > > -----Original Message----- > From: Robert Bays [mailto:[EMAIL PROTECTED] > Sent: Wednesday, September 12, 2007 3:24 AM > To: Daren Tay > Cc: vyatta-users@mailman.vyatta.com > Subject: Re: [Vyatta-users] Running Vyatta in RAID 1 setup? > Performancemonitoring? > > > Given that software RAID takes up processor cycles, yes expect some > performance hit. Since it's not something we regularly test though I > can't guess as to how much to expect. > > Daren Tay wrote: >> So I will need to create the device when I run Vyatta from LiveCD, then do >> the installation? >> >> Think I should give that try.. but would I experience a performance hit? >> >> Daren >> >> -----Original Message----- >> From: Robert Bays [mailto:[EMAIL PROTECTED] >> Sent: Wednesday, 29 August 2007 02:28 >> To: Daren Tay >> Cc: vyatta-users@mailman.vyatta.com >> Subject: Re: [Vyatta-users] Running Vyatta in RAID 1 setup? >> Performancemonitoring? >> >> >> It's possible, but untested. You would need to apt-get mdadm from the >> repository and create the raid device before you run install-system. >> >> Cheers, >> Robert. >> >> Daren Tay wrote: >>> Anyone knows if it is possible? >>> >>> -----Original Message----- >>> From: [EMAIL PROTECTED] >>> [mailto:[EMAIL PROTECTED] Behalf Of Daren Tay >>> Sent: Monday, 27 August 2007 10:50 >>> To: vyatta-users@mailman.vyatta.com >>> Subject: [Vyatta-users] Running Vyatta in RAID 1 setup? >>> Performancemonitoring? >>> >>> >>> Hi guys, >>> >>> how do I install Vyatta in a Linux Software RAID environment? >>> So far, I think it doesn't... because I wasn't prompt during > installation. >>> The installation was too easy (hahaha!) >>> >>> Also, what softwares/methods can I use to monitor Vyatta raid > performance? >>> Thanks! >>> Daren >>> >>> _______________________________________________ >>> Vyatta-users mailing list >>> Vyatta-users@mailman.vyatta.com >>> http://mailman.vyatta.com/mailman/listinfo/vyatta-users >>> _______________________________________________ >>> Vyatta-users mailing list >>> Vyatta-users@mailman.vyatta.com >>> http://mailman.vyatta.com/mailman/listinfo/vyatta-users > _______________________________________________ Vyatta-users mailing list Vyatta-users@mailman.vyatta.com http://mailman.vyatta.com/mailman/listinfo/vyatta-users