uswgi restart - no delay nginx restart - about a 12 second delay for the first request if running https
nginx restart - no delay if running http -Jim On Thu, Aug 21, 2014 at 10:08 AM, Richard Vézina < [email protected]> wrote: > I have 10m and I don't have this issue... > > I don't think it coming from nginx. > > There is very few parameters in nginx config that could explain your > latency... > > Does it happen only on reboot of VM, or it happen when you restart nginx, > or uwsgi. What happen if you restart nginx only vs restart uwsgi only. And > what happen if you try to start manually uwsgi after reboot of the VM > before first aptempt to connect to your app. Maybe uwsgi is not started and > get strat by nginx, that should not be the case though, they have both to > be strated independently. > > You can try your app in other VM and determine if the latency was there or > not. > > All these test can help you figure out where to dig up further. > > Richard > > > > > On Thu, Aug 21, 2014 at 10:46 AM, Jim Steil <[email protected]> wrote: > >> I've changed the following in /etc/nginx/sites-available/web2py >> >> ssl_session_cache shared:SSL:10m; -> to 60m >> ssl_session_timeout 10m; -> to 60m >> >> Still took a long time (5-10 seconds) for the first request but maybe now >> it will not cause that to happen again for greater intervals. >> >> -Jim >> >> >> On Wed, Aug 20, 2014 at 9:17 PM, Cliff Kachinske <[email protected]> >> wrote: >> >>> The install script in the book may not be correct for your version of >>> Web2py. >>> >>> A good first step might be to check the script's config settings against >>> the ones from the book. >>> >>> >>> On Wednesday, August 20, 2014 4:49:28 PM UTC-4, Jim S wrote: >>>> >>>> I did this and after waiting 45 minutes and re-testing, it did not >>>> exhibit the slow behavior. Since this is a test without running >>>> nginx/uwsgi I'm assuming my problem is in one of those layers. >>>> >>>> Also, I access the production site with http instead of https, the >>>> slowness isn't there either. >>>> >>>> -Jim >>>> >>>> On Wednesday, August 20, 2014 2:26:35 PM UTC-5, Richard wrote: >>>>> >>>>> You can check that with profiler : python web2py.py -a 'asdf' -i >>>>> 127.0.0.1 -p 8000 appname -F fileNameForProfilerDumpInfo' >>>>> >>>>> Your app will be very slow with profiler. >>>>> >>>>> Richard >>>>> >>>>> >>>>> On Wed, Aug 20, 2014 at 3:24 PM, Richard Vézina <[email protected] >>>>> > wrote: >>>>> >>>>>> Could your app take time to create global vars and after they are >>>>>> cached up? >>>>>> >>>>>> Richard >>>>>> >>>>>> >>>>>> On Wed, Aug 20, 2014 at 1:32 PM, Jim S <[email protected]> wrote: >>>>>> >>>>>>> Hi >>>>>>> >>>>>>> I've installed web2py on my ubuntu machine using the script at the >>>>>>> bottom of this section in the book: >>>>>>> >>>>>>> http://web2py.com/books/default/chapter/29/13/ >>>>>>> deployment-recipes#Nginx >>>>>>> >>>>>>> It is all working well except for one annoyance. >>>>>>> >>>>>>> If I leave the let the page site for a while (haven't really >>>>>>> determined the time period needed to display the behavior), when I come >>>>>>> back later my first access to the application is really slow, like 10 >>>>>>> seconds to display the page. But, after that, it clicks along with >>>>>>> sub-second response time. >>>>>>> >>>>>>> Anyone have any idea what is going on or where to begin >>>>>>> trouble-shooting? >>>>>>> >>>>>>> -Jim >>>>>>> >>>>>>> -- >>>>>>> Resources: >>>>>>> - http://web2py.com >>>>>>> - http://web2py.com/book (Documentation) >>>>>>> - http://github.com/web2py/web2py (Source code) >>>>>>> - https://code.google.com/p/web2py/issues/list (Report Issues) >>>>>>> --- >>>>>>> You received this message because you are subscribed to the Google >>>>>>> Groups "web2py-users" group. >>>>>>> To unsubscribe from this group and stop receiving emails from it, >>>>>>> send an email to [email protected]. >>>>>>> For more options, visit https://groups.google.com/d/optout. >>>>>>> >>>>>> >>>>>> >>>>> -- >>> Resources: >>> - http://web2py.com >>> - http://web2py.com/book (Documentation) >>> - http://github.com/web2py/web2py (Source code) >>> - https://code.google.com/p/web2py/issues/list (Report Issues) >>> --- >>> You received this message because you are subscribed to a topic in the >>> Google Groups "web2py-users" group. >>> To unsubscribe from this topic, visit >>> https://groups.google.com/d/topic/web2py/3tmtJeQW9GI/unsubscribe. >>> To unsubscribe from this group and all its topics, send an email to >>> [email protected]. >>> >>> For more options, visit https://groups.google.com/d/optout. >>> >> >> -- >> Resources: >> - http://web2py.com >> - http://web2py.com/book (Documentation) >> - http://github.com/web2py/web2py (Source code) >> - https://code.google.com/p/web2py/issues/list (Report Issues) >> --- >> You received this message because you are subscribed to the Google Groups >> "web2py-users" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> >> For more options, visit https://groups.google.com/d/optout. >> > > -- > Resources: > - http://web2py.com > - http://web2py.com/book (Documentation) > - http://github.com/web2py/web2py (Source code) > - https://code.google.com/p/web2py/issues/list (Report Issues) > --- > You received this message because you are subscribed to a topic in the > Google Groups "web2py-users" group. > To unsubscribe from this topic, visit > https://groups.google.com/d/topic/web2py/3tmtJeQW9GI/unsubscribe. > To unsubscribe from this group and all its topics, send an email to > [email protected]. > For more options, visit https://groups.google.com/d/optout. > -- Resources: - http://web2py.com - http://web2py.com/book (Documentation) - http://github.com/web2py/web2py (Source code) - https://code.google.com/p/web2py/issues/list (Report Issues) --- You received this message because you are subscribed to the Google Groups "web2py-users" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
