Good that it is fixed. If you restart weeWX and provided there are records stored in the logger that are newer than the last record in your database weeWX should attempt to down load them as part of the weeWX startup. If none are downloaded either there is nothing in your logger or the last record in your logger is older than the last record in your database.
Not sure what you mean by my second email, I only replied once as far as I know? In any case to use debug = 1 you need to make the change in weewx.conf, save weewx.conf then restart weeWX. If you have any concerns post a copy of the log, including the weeWX startup pre-amble from the log will show what debug setting is being used. Gary On Monday, 5 November 2018 10:14:33 UTC+10, [email protected] wrote: > > You are the master, option one worked well, we will see if it can recover > the archive data in the station receiver but that is less important then > getting everything back online. Thanks for your dedication to the > application, I suspected it was something related to the bad records in the > receiver but was not sure how to figure it out. One NOTE I have the > debugging level set to 1 in the config file and it does not produce the > detail you shown on your log in your second email, not sure how that > works. But thanks again! > > On Sunday, November 4, 2018 at 5:24:10 PM UTC-6, gjr80 wrote: >> >> Hi, >> >> If I understand your posts correctly you had a working Vantage install, >> there was a power outage and despite things seeming to have come backup up >> fine the data on your pages is not being updated despite the pages >> themselves being generated every 5 minutes? It's quite possible that as a >> result of the power outage you have corrupted station memory, this is >> something to watch out for with Vantage stations. When this happens your >> station continues to send loop packets every 2.5 odd seconds but the >> station does not send the archive records (every 5 minutes in your case). >> If weeWX is set to use hardware record generation (the norm for Vantage >> stations) then weeWX never gets an archive record, no records are added to >> the database and consequently the reports are run but with no new data. The >> result is you see pages that are updating but with no new data. When run >> directly <http://weewx.com/docs/usersguide.htm#Running_directly> weeWX >> appears to be working normally as you will see incoming loop packets (the >> LOOP: lines) but if you look carefully you will not see any archive records >> (REC: lines) on the 5 minute boundaries. If you look at your log you will >> see what appears to be normal activity but no lines indicating records were >> added to the database, carefully compare you post-power outage log to those >> from before the power outage. Feel free to post a good 15 minutes of the >> current log here if you are unsure. >> >> The fix is relatively simple and may or may not result in loss of some >> data. Have a look at the Corrupt station memory >> <http://weewx.com/docs/usersguide.htm#html_generated_but_not_updated> >> section in the User's Guide <http://weewx.com/docs/usersguide.htm>. >> There are a couple of fixes there, try them, start with 1. and then 2.. If >> you need to clear the memory take note of the suggestion to dump the logger >> memory first as that may prevent/minimise loss of historical data. >> >> Of course, if that is not the problem then we need to look elsewhere. >> >> Gary >> >> On Monday, 5 November 2018 08:39:14 UTC+10, [email protected] wrote: >>> >>> UPDATE: Was looking at the home server not the ranch OPPS! I still >>> have an issue with the update. >>> >>> >>> On Sunday, November 4, 2018 at 3:37:03 PM UTC-6, [email protected] >>> wrote: >>>> >>>> Hi All, >>>> >>>> I had a working setup but had a similar issue when I first started the >>>> system but some how it fixed itself, but I lost power to the remote site >>>> for a period of time and I am in the process of getting things back up and >>>> running. >>>> >>>> Platform: Raspberry Pi >>>> Vantage Pro2 Station >>>> Installed from distribution and customized(Web Pages) >>>> running the daemon at boot >>>> >>>> Looking at the log files indicates that the system seems to be up and >>>> running properly. The weewx deamon did update the time properly on the >>>> weather station receiver. According to the messages and syslog the >>>> station >>>> is updating pages & images every 5 minutes. I checked the >>>> /var/www/html/weewx directory for the web server and the date timestamps >>>> looks like the files are being updated every 5 minutes. I have noticed in >>>> syslog that occasionally copies 0 files but checking the web directory the >>>> files are being updated correct timestamps (Strange) . I stopped the >>>> deamon and ran the weewxd from the command line and I could see the data >>>> updating on the console window and it looks correct. >>>> >>>> I just don't know what has got the system locked up where the web >>>> page(index.html) and the images are not updating, I get the same static >>>> data in both every 5 minutes. >>>> >>>> Any clues? >>>> >>>> Thanks >>>> >>>> Richard >>>> >>> -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
