Just tried disabling rapid fire but no change. Its still incrementing as
previously... That 2.2.x figure still pops up.. Not sure where its pulling
this from
using rain_total 2.248
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
ignored parameter action=updateraw
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
unrecognized parameter weeklyrainin=0.00
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread: raw
packet: {'wind_speed': 2.7, 'humidity_in': 54.0, 'temperature_in': 72.7,
'barometer': 30.3, 'windchill': 70.9, 'dewpoint': 45.5, 'humidity_out':
40.0, 'uv': 0.0, 'radiation': 50.65, 'rain': 0.0, 'dateTime': 1558505079,
'temperature_out': 70.9, 'wind_dir': 17.0, 'rain_total': 2.25, 'usUnits':
1, 'wind_gust': 3.4}
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
mapped packet: {'barometer': 30.3, 'windchill': 70.9, 'dewpoint': 45.5,
'outHumidity': 40.0, 'UV': 0.0, 'radiation': 50.65, 'rain': 0.0,
'dateTime': 1558505079, 'windDir': 17.0, 'outTemp': 70.9, 'windSpeed': 2.7,
'inHumidity': 54.0, 'inTemp': 72.7, 'windGust': 3.4, 'usUnits': 1}
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: ServerThread:
POST:
PASSKEY=XXXX&stationtype=EasyWeatherV1.3.2&dateutc=2019-05-22+06:04:39&tempinf=72.7&humidityin=54&baromrelin=30.30&baromabsin=29.69&tempf=70.9&humidity=40&winddir=17&windspeedmph=2.7&windspdmph_avg10m=0.0&windgustmph=3.4&maxdailygust=6.9&rainratein=0.000&eventrainin=0.000&hourlyrainin=0.000&dailyrainin=0.000&weeklyrainin=0.000&monthlyrainin=
1.346&yearlyrainin=2.248&solarradiation=50.65&uv=0
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread: raw
data:
PASSKEY=B49D741DD8D21E1D5B657ADE7C3A9D91&stationtype=EasyWeatherV1.3.2&dateutc=2019-05-22+06:04:39&tempinf=72.7&humidityin=54&baromrelin=30.30&baromabsin=29.69&tempf=70.9&humidity=40&winddir=17&windspeedmph=2.7&windspdmph_avg10m=0.0&windgustmph=3.4&maxdailygust=6.9&rainratein=0.000&eventrainin=0.000&hourlyrainin=0.000&dailyrainin=0.000&weeklyrainin=0.000&monthlyrainin=
1.346&yearlyrainin=2.248&solarradiation=50.65&uv=0
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
using rain_total 2.248 from yearlyrainin
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
unrecognized parameter eventrainin=0.000
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
unrecognized parameter baromrelin=30.30
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
unrecognized parameter maxdailygust=6.9
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
unrecognized parameter monthlyrainin=1.346
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
unrecognized parameter PASSKEY=
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
unrecognized parameter humidityin=54
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
unrecognized parameter rainratein=0.000
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
unrecognized parameter windspdmph_avg10m=0.0
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
unrecognized parameter hourlyrainin=0.000
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
unrecognized parameter baromabsin=29.69
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
unrecognized parameter tempinf=72.7
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
unrecognized parameter uv=0
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
unrecognized parameter stationtype=EasyWeatherV1.3.2
May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
unrecognized parameter weeklyrainin=0.000
On Wednesday, May 22, 2019 at 2:46:57 PM UTC+10, gjr80 wrote:
>
> Hi,
>
> Not an interceptor or ECOWITT HP2551 user but looking at your log1.txt log
> extract it appears that your station is sending both rapidfire as well as
> normal (non-rapidfire) updates.
>
> Rapid fire:
> May 22 07:40:02 UBUNTUMATE-1000H weewx[26366]: interceptor: ServerThread:
> GET: ID=IVICTORI1768&PASSWORD=XXXX&indoortempf=71.1&tempf=54.3&dewptf=47.7
> &windchillf=54.3&indoorhumidity=52&humidity=78&windspeedmph=6.9&
> windgustmph=8.1&winddir=40&absbaromin=29.73&baromin=30.34&rainin=0.00&
> dailyrainin=0.00&weeklyrainin=0.00&monthlyrainin=1.35&yearlyrainin=2.25&
> solarradiation=16.88&UV=0&dateutc=2019-05-21%2021:40:01&softwaretype=
> EasyWeatherV1.3.2&action=updateraw&realtime=1&rtfreq=5
>
> normal:
> May 22 07:40:18 UBUNTUMATE-1000H weewx[26366]: interceptor: ServerThread:
> POST: PASSKEY=XXXX&stationtype=EasyWeatherV1.3.2&dateutc=2019-05-21+21:40:
> 17&tempinf=71.4&humidityin=52&baromrelin=30.34&baromabsin=29.73&tempf=54.3
> &humidity=78&winddir=18&windspeedmph=5.4&windspdmph_avg10m=0.0&windgustmph
> =6.9&maxdailygust=15.9&rainratein=0.000&eventrainin=0.000&hourlyrainin=
> 0.000&dailyrainin=0.000&weeklyrainin=0.000&monthlyrainin=1.346&
> yearlyrainin=2.248&solarradiation=16.02&uv=0
>
> This really shouldn't be an issue but if you have a look at the number of
> decimal places used for each rain related observation in each you will see
> the RF updates use 2 decimal places and the normal updates 3 decimal
> places. Consequently, when you have normal after a RF you get a rain
> counter wraparound detected and your rainfall has the wrapped around figure
> added. If you have RF after normal you get 0.002 inches added. RF after RF
> has no effect as both yearly rain fields are identical. I don't think using
> any of the other rain fields will make a difference because the same
> decimal places difference exist with both.
>
> Maybe less than ideal but can you turn off RF updates on your station,
> that would at last show if that cures the issue or not. If so, maybe the
> solution is to get the interceptor driver to ignore either the RF updates
> or the normal updates. Not sure whether it can or not, probably one for
> Matthew the author.
>
> Gary
>
> On Wednesday, 22 May 2019 14:13:03 UTC+10, Joe Santas wrote:
>>
>> Cleared the settings on the weatherstation. Same issue again. Obviously
>> something else is going on. Also tried shutting down the weather station
>> and deleting the weewx.sdb file so it re creates a new one but no joy so
>> far.
>> I have attached the latest copy of the log.
>>
>> Regards
>>
>>
>>
>> On Wednesday, May 22, 2019 at 2:22:50 AM UTC+10, Gábor Szabados wrote:
>>>
>>> Sounds like a plan. Let me know once you have done it.
>>>
>>> Interceptor should receive only the wu messages, then it should not have
>>> any issue.
>>>
>>> Gabor
>>>
>>> Joe Santas <[email protected]> ezt írta (időpont: 2019. máj. 21., Ke
>>> 17:41):
>>>
>>>> From what i have read they specify just the tcp to port 80 which i
>>>> already have in place. What i will do is deactivate the upload features
>>>> in
>>>> the weatherstation its self and see if it makes a difference and leave the
>>>> rules i currently have in place and see if this sorts it.
>>>> Once this is done i will configure weewx config file to push the data
>>>> up to wunderground and weathercloud any any other services i use.
>>>>
>>>> Regards
>>>>
>>>> On Wednesday, May 22, 2019 at 1:35:11 AM UTC+10, Gábor Szabados wrote:
>>>>>
>>>>> Read about how you can redirect only the traffic to WU servers to your
>>>>> weewx server then you will be ok.
>>>>>
>>>>> I've seen some Merlin router firmware descriptions how it can be done.
>>>>> Or DD-WRT descriptions are around the net too.
>>>>>
>>>>> Gabor
>>>>>
>>>>> Joe Santas <[email protected]> ezt írta (időpont: 2019. máj. 21., Ke
>>>>> 16:22):
>>>>>
>>>>>> You may be onto something. So i will have to turn off the non wu
>>>>>> servers on the device its self. Im unable to do this as i am at work
>>>>>> but i
>>>>>> can reconfigure my router remotely to route the correct traffic. I can
>>>>>> try
>>>>>> this from work. Which protocol should i leave active? At the moment i
>>>>>> am
>>>>>> forwarding all tcp traffic to my weewx server from the weather station.
>>>>>>
>>>>>> Regards
>>>>>>
>>>>>> On Wednesday, May 22, 2019 at 12:13:36 AM UTC+10, Gábor Szabados
>>>>>> wrote:
>>>>>>>
>>>>>>> I can see more issues there, because I faced a similar one before.
>>>>>>>
>>>>>>> One of your issues, maybe the main one, that your weather station is
>>>>>>> sending reports to multiple servers and all of them ia redirected to
>>>>>>> your
>>>>>>> weewx. Interceptor tries to parse all the messages and faces a mixed
>>>>>>> state
>>>>>>> with yearlyrainin and dailyrainin and some rounding issues.
>>>>>>>
>>>>>>> First try to turn off the reporting to the non-wu servers. Or set
>>>>>>> your router to forward only the wu request to your weewx. Then the
>>>>>>> interceptor will recieve and parse only one kind of messages.
>>>>>>>
>>>>>>> Gabor
>>>>>>>
>>>>>>> Joe Santas <[email protected]> ezt írta (időpont: 2019. máj. 21.,
>>>>>>> Ke 15:52):
>>>>>>>
>>>>>>>> wraparound detected in this log.
>>>>>>>> After clearing the database rainfall graph has started to populate
>>>>>>>> once again even though no rain lol.
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> On Tuesday, May 21, 2019 at 5:12:03 PM UTC+10, Gábor Szabados wrote:
>>>>>>>>>
>>>>>>>>> Hi Joe,
>>>>>>>>>
>>>>>>>>> Could you try to look for messages in the log, like interceptor:
>>>>>>>>> MainThread: rain counter wraparound detected:
>>>>>>>>>
>>>>>>>>> I can see a rounding issue (maybe) at the yearly rain is once
>>>>>>>>> 2.248 the then 2.25, when no weekly rain change.
>>>>>>>>>
>>>>>>>>> May 21 02:53:17 UBUNTUMATE-1000H weewx[7192]: interceptor:
>>>>>>>>> MainThread: raw data:
>>>>>>>>> PASSKEY=********************&stationtype=EasyWeatherV1.3.2&dateutc=2019-05-20+16:53:05&tempinf=65.8&humidityin=60&baromrelin=30.14&baromabsin=29.54&tempf=55.4&humidity=77&winddir=16&windspeedmph=2.9&windspdmph_avg10m=0.0&windgustmph=3.4&maxdailygust=8.1&rainratein=0.000&eventrainin=0.000&hourlyrainin=0.000&dailyrainin=0.000&weeklyrainin=0.000&monthlyrainin=1.346&yearlyrainin=2.248&solarradiation=0.00&uv=0
>>>>>>>>>
>>>>>>>>> May 21 02:53:22 UBUNTUMATE-1000H weewx[7192]: interceptor:
>>>>>>>>> ServerThread: GET:
>>>>>>>>> ID=*********&PASSWORD=****&indoortempf=65.8&tempf=55.4&dewptf=48.4&windchillf=55.4&indoorhumidity=60&humidity=77&windspeedmph=2.9&windgustmph=3.4&winddir=16&absbaromin=29.54&baromin=30.14&rainin=0.00&dailyrainin=0.00&weeklyrainin=0.00&monthlyrainin=1.35&yearlyrainin=2.25&solarradiation=0.00&UV=0&dateutc=2019-05-20%2016:53:21&softwaretype=EasyWeatherV1.3.2&action=updateraw&realtime=1&rtfreq=5
>>>>>>>>>
>>>>>>>>> Look for wraparound events and check on your console too what is
>>>>>>>>> your yearly value. Try to find places where the yearlyrainin changes
>>>>>>>>> and
>>>>>>>>> where it calculates rain from the change then I can try to find you
>>>>>>>>> the
>>>>>>>>> logic what goes wrong. Look for dateutc values too, is it incremental
>>>>>>>>> or
>>>>>>>>> changes back time to time when wraparound happens, if happens.
>>>>>>>>>
>>>>>>>>> Best Regards,
>>>>>>>>>
>>>>>>>>> Gabor
>>>>>>>>>
>>>>>>>>> --
>>>>>>>> You received this message because you are subscribed to the Google
>>>>>>>> Groups "weewx-user" group.
>>>>>>>> To unsubscribe from this group and stop receiving emails from it,
>>>>>>>> send an email to [email protected].
>>>>>>>> To view this discussion on the web visit
>>>>>>>> https://groups.google.com/d/msgid/weewx-user/f4434e12-7ed4-4a60-bc6c-42ff8de0d5ee%40googlegroups.com
>>>>>>>>
>>>>>>>> <https://groups.google.com/d/msgid/weewx-user/f4434e12-7ed4-4a60-bc6c-42ff8de0d5ee%40googlegroups.com?utm_medium=email&utm_source=footer>
>>>>>>>> .
>>>>>>>> For more options, visit https://groups.google.com/d/optout.
>>>>>>>>
>>>>>>> --
>>>>>> You received this message because you are subscribed to a topic in
>>>>>> the Google Groups "weewx-user" group.
>>>>>> To unsubscribe from this topic, visit
>>>>>> https://groups.google.com/d/topic/weewx-user/lg4W_4qHTaQ/unsubscribe.
>>>>>> To unsubscribe from this group and all its topics, send an email to
>>>>>> [email protected].
>>>>>> To view this discussion on the web visit
>>>>>> https://groups.google.com/d/msgid/weewx-user/30272d74-fedd-46a6-9a0f-ba66112df697%40googlegroups.com
>>>>>>
>>>>>> <https://groups.google.com/d/msgid/weewx-user/30272d74-fedd-46a6-9a0f-ba66112df697%40googlegroups.com?utm_medium=email&utm_source=footer>
>>>>>> .
>>>>>> For more options, visit https://groups.google.com/d/optout.
>>>>>>
>>>>> --
>>>> You received this message because you are subscribed to the Google
>>>> Groups "weewx-user" group.
>>>> To unsubscribe from this group and stop receiving emails from it, send
>>>> an email to [email protected].
>>>> To view this discussion on the web visit
>>>> https://groups.google.com/d/msgid/weewx-user/a5b531bf-8bd0-4ede-8ae4-6d5d84f34a3a%40googlegroups.com
>>>>
>>>> <https://groups.google.com/d/msgid/weewx-user/a5b531bf-8bd0-4ede-8ae4-6d5d84f34a3a%40googlegroups.com?utm_medium=email&utm_source=footer>
>>>> .
>>>> For more options, visit https://groups.google.com/d/optout.
>>>>
>>>
--
You received this message because you are subscribed to the Google Groups
"weewx-user" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/weewx-user/e44bf030-458a-45c4-8a98-0a52af19cb5d%40googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
