Hi and thanks in advance for any help! I have an Arduino sending weather data to a Raspberry Pi. I'm using WeeWX with the FileParse driver and the Seasons skin. Up until sometime yesterday, I was able to see wind gust data in the web page and in the graphs. Suddenly, for reasons unknown, I am unable to see the data in the charts and the web page shows no entry at all for wind gust and direction. NA NA ( NA) is what is displayed in it's place. I can see the values for windGust in the incoming datastream. I've looked everywhere that I know, but can't seem to find the reason. I've started a new database, but that had no effect.
Weewx.conf: # WEEWX CONFIGURATION FILE # # Copyright (c) 2009-2019 Tom Keffer <[email protected]> # See the file LICENSE.txt for your rights. ############################################################################## # Set to type of station hardware. There must be a corresponding stanza # in this file with a 'driver' parameter indicating the driver to be used. station_type = FileParse # If you have a website, you may specify an URL #station_url = http://www.example.com station_url = localhost/weewx # The start of the rain year (1=January; 10=October, etc.). This is # downloaded from the station if the hardware supports it. rain_year_start = 1 # Start of week (0=Monday, 6=Sunday) week_start = 6 ############################################################################# [FileParse] poll_interval = 10 path = /var/tmp/data.csv driver = user.fileparse loop_interval = 10 [[Label_Map]] Time = dateTime pressure = pressure outTemp = outTemp outHumidity = outHumidity windSpeed = windSpeed windDir = windDir windGust = windGust windGustDir = windGustDir supplyVoltage = supplyVoltage lightLevel = radiation rainRate = rainRate rain = rain ############################################################################## # This section specifies what reports, using which skins, to generate. [StdReport] [[SeasonsReport]] # The SeasonsReport uses the 'Seasons' skin, which contains the # images, templates and plots for the report. skin = Seasons enable = true # Various options for customizing your reports. [[Defaults]] [[[Units]]] # The following section sets what unit to use for each unit group. # NB: The unit is always in the singular. I.e., 'mile_per_hour', # NOT 'miles_per_hour' [[[[Groups]]]] group_altitude = foot # Options are 'foot' or 'meter' group_degree_day = degree_F_day # Options are 'degree_F_day' or 'degree_C_day' group_pressure = inHg # Options are 'inHg', 'mmHg', 'mbar', or 'hPa' group_rain = inch # Options are 'inch', 'cm', or 'mm' group_rainrate = inch_per_hour # Options are 'inch_per_hour', 'cm_per_hour', or 'mm_per_hour' group_speed = mile_per_hour # Options are 'mile_per_hour', 'km_per_hour', 'knot', or 'meter_per_second' group_speed2 = mile_per_hour2 # Options are 'mile_per_hour2', 'km_per_hour2', 'knot2', or 'meter_per_second2' group_temperature = degree_F # Options are 'degree_F' or 'degree_C' # The following section sets the formatting for each type of unit. [[[[StringFormats]]]] centibar = %.0f cm = %.2f cm_per_hour = %.2f degree_C = %.1f degree_F = %.1f degree_compass = %.0f foot = %.0f hPa = %.1f hour = %.1f inHg = %.3f inch = %.2f inch_per_hour = %.2f km_per_hour = %.0f km_per_hour2 = %.1f knot = %.0f knot2 = %.1f mbar = %.1f meter = %.0f meter_per_second = %.1f meter_per_second2 = %.1f mile_per_hour = %.0f mile_per_hour2 = %.1f mm = %.1f mmHg = %.1f mm_per_hour = %.1f percent = %.0f second = %.0f uv_index = %.1f volt = %.1f watt_per_meter_squared = %.0f NONE = " N/A" # The following section sets the label for each type of unit [[[[Labels]]]] day = " day", " days" hour = " hour", " hours" minute = " minute", " minutes" second = " second", " seconds" NONE = "" # The following section sets the format for each time scale. # The values below will work in every locale, but they may not look # particularly attractive. [[[[TimeFormats]]]] hour = %H:%M day = %X week = %X (%A) month = %x %X year = %x %X rainyear = %x %X current = %x %X ephem_day = %X ephem_year = %x %X [[[[Ordinates]]]] # Ordinal directions. The last one is for no wind direction directions = N, NNE, NE, ENE, E, ESE, SE, SSE, S, SSW, SW, WSW, W, WNW, NW, NNW, N/A # The following section sets the base temperatures used for the # calculation of heating and cooling degree-days. [[[[[DegreeDays]]]]] # Base temperature for heating days, with unit: heating_base = 65, degree_F # Base temperature for cooling days, with unit: cooling_base = 65, degree_F # A trend takes a difference across a time period. The following # section sets the time period, and how big an error is allowed to # still be counted as the start or end of a period. [[[[[Trend]]]]] time_delta = 10800 # 3 hours time_grace = 300 # 5 minutes # The labels to be used for each observation type [[[Labels]]] # Set to hemisphere abbreviations suitable for your location: hemispheres = N, S, E, W # Formats to be used for latitude whole degrees, longitude whole # degrees, and minutes: latlon_formats = %02d, %03d, %05.2f # Generic labels, keyed by an observation type. [[[[Generic]]]] barometer = Barometer dewpoint = Dew Point ET = ET heatindex = Heat Index inHumidity = Inside Humidity inTemp = Inside Temperature outHumidity = Humidity outTemp = Outside Temperature radiation = Radiation rain = Rain Today rainRate = Rain Last Hour UV = UV Index windDir = Wind Direction windGust = Gust Speed windGustDir = Gust Direction windSpeed = Wind Speed windchill = Wind Chill windgustvec = Gust Vector windvec = Wind Vector extraTemp1 = Temperature1 extraTemp2 = Temperature2 extraTemp3 = Temperature3 # Sensor status indicators rxCheckPercent = Signal Quality txBatteryStatus = Transmitter Battery windBatteryStatus = Wind Battery rainBatteryStatus = Rain Battery outTempBatteryStatus = Outside Temperature Battery inTempBatteryStatus = Inside Temperature Battery consBatteryVoltage = Console Battery heatingVoltage = Heating Battery supplyVoltage = Supply Voltage referenceVoltage = Reference Voltage ############################################################################## # This section controls the origin of derived values. [StdWXCalculate] [[Calculations]] # How to calculate derived quantities. Possible values are: # hardware - use the value provided by hardware # software - use the value calculated by weewx # prefer_hardware - use value provide by hardware if available, # otherwise use value calculated by weewx pressure = hardware barometer = software altimeter = software windchill = software heatindex = software dewpoint = software inDewpoint = software rainRate = hardware ############################################################################## # This section is for configuring the archive service. [StdArchive] # If the station hardware supports data logging then the archive interval # will be downloaded from the station. Otherwise, specify it (in seconds). archive_interval = 300 # If possible, new archive records are downloaded from the station # hardware. If the hardware does not support this, then new archive # records will be generated in software. # Set the following to "software" to force software record generation. record_generation = hardware # Whether to include LOOP data in hi/low statistics loop_hilo = False # The data binding used to save archive records data_binding = wx_binding ############################################################################## # This section binds a data store to a database. [DataBindings] [[wx_binding]] # The database must match one of the sections in [Databases]. # This is likely to be the only option you would want to change. database = archive_sqlite # The name of the table within the database table_name = archive # The manager handles aggregation of data for historical summaries manager = weewx.wxmanager.WXDaySummaryManager # The schema defines the structure of the database. # It is *only* used when the database is created. schema = schemas.wview.schema ############################################################################## # This section defines various databases. [Databases] # A SQLite database is simply a single file [[archive_sqlite]] database_name = weewx.sdb database_type = SQLite ############################################################################# -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/weewx-user/d342b165-7ffc-4508-88da-78bcd70fc775%40googlegroups.com. For more options, visit https://groups.google.com/d/optout.
