i use the same client software, but interceptor did not work without modification. if it doesn't work, take a look at my post here https://groups.google.com/g/weewx-user/c/9tWaYfvIyWg
On Thursday, January 28, 2021 at 3:33:31 PM UTC+1 [email protected] wrote: > Yes, "weewx" can access the TP3000WC over wifi. > > Steps I followed: > > Tycon Systems, TP3000WC and installing “weewx” > > EasyWeather firmware needs to be version 1.5.6 for this procedure to > work. Firmware version can be found in the “WS View.” “Customized” > screen. TP3000WC, anemometer (wind speed cups) need to be on top of the > sensor arrary. > > 1. Downloaded and installed Linux Mint: Linux Mint Download > <https://www.linuxmint.com/download.php> > > 2. Installed “weewx” using: Debian install instructions > <https://www.linuxmint.com/download.php> > > This will insure paths are correct. > > 3. Downloaded and installed “weewx” driver: Interceptor driver > <https://github.com/matthewwall/weewx-interceptor> > > Follow driver install instructions; stop after doing: > > *sudo wee_config --reconfigure --driver=user.interceptor > –no-prompt* > > 4. Configured “Interceptor” driver in “weewx.conf:” *sudo nano > /etc/weewx/weewx.conf* > > Near the top of “weew.conf;” change “debug = 0” to “debug = > 1” Next; in section “[Interceptor]” modify the following to > match: > > > ############################################################################## > > *[Interceptor]* > > # This section is for the network traffic interceptor driver. > > # The driver to use: > > *driver = user.interceptor* > > # Specify the hardware device to capture. Options include: > > # acurite-bridge - acurite internet bridge, smarthub, or access > > # observer - fine offset WH2600/HP1000/HP1003, ambient WS2902 > > # lw30x - oregon scientific LW301/LW302 > > # lacrosse-bridge - lacrosse GW1000U/C84612 internet bridge > > # ecowitt-client - any hardware that uses the ecowitt protocol > > # wu-client - any hardware that uses the weather underground protocol > > *device_type = ecowitt-client* > > * port = 8000* > > * iface = eth0* > > > ############################################################################## > > Note: iface may be different: *sudo ifconfig*; look for your computer > ip, on left will be the iface. > > 5. Installed Android app and install: WS View app for Android > Smartphone > <https://play.google.com/store/apps/details?id=com.ost.wsview&hl=en> > > 6. Installed device; select icon that looks like your TP3000WC, > display. Followed on screen instructions. Consult TP3000WC > manual, page 33: “Connecting the Weather Station Console to Wi-Fi” > for additional information if needed. > > 7. When device appears in the device list of the “WS View” app > tap on device, tapped “Next” in the upper right corner four times. > This will be the “Customized” screen. > > 8. Modified “Customized” screen; as shown in this image, except > for the ip address --should be the ip address of computer where > “weewx” is running. Find the ip address by entering : > *sudo > ifconfig* in terminal; on the computer where “weewx” is running. > > [image: WS View --settings.JPG] > > Later I changed Upload interval to 30 seconds. > > 9. Make sure “weewx” service is stopped: *sudo /etc/init.d/weewx > stop* > > 10. Start “weewx:” *sudo /etc/init.d/weewx start > /etc/weewx/weewx.conf* > > 11. Back in terminal; type: *sudo tail -f /var/log/syslog | grep > weewx* You should see data coming int > > William > On Wednesday, September 26, 2018 at 5:15:20 PM UTC-4 [email protected] > wrote: > >> Hi, >> >> Pretty new to weewx and I'm looking to replace my Accurite 5 in 1 with >> something better. >> >> This is now available on amazon >> >> >> https://www.amazon.com/ProWeatherStation-TP3000WC-Professional-Wireless-Weather/dp/B07G7DHG4L/ref=sr_1_2?s=lawn-garden&ie=UTF8&qid=1537994372&sr=1-2&keywords=Tycon+Power+Systems >> >> for a really good price, too. >> >> I believe that it is a Fine Offset device but it doesn't seem to have a >> USB port--only wifi. Can weewx access a weather station over wifi? >> >> Jeff Ross >> > -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/weewx-user/cf7ce443-43e0-477f-8030-857e2eee10bbn%40googlegroups.com.
