I'm not planning any factory resets! Thanks for the extra info. Hopefully however it will be long enough that by the time I need to setup another Fine Offset I've forgotten about that forum. :)
On Sunday, 21 March 2021 at 14:19:26 UTC [email protected] wrote: > Congratulations ! > It is how it is .... - and, unless you do a factory reset, you won't have > to do this again. > > For "general" FineOffset clone issues etc., WXforum is afaik the main (in > the sense most substantial) forum - for weewx there are some helpful posts, > too - but here is the main weewx user forum. > > With the GW1000/WH2650 > > in weewx.conf you will have to add the line > ------------------ start weewx.conf excerpt ------------------ > [StdCalibrate] > > [[Corrections]] > # For each type, an arbitrary calibration expression can be given. > # It should be in the units defined in the StdConvert section. > # Example: > foo = foo + 0.2 > > * radiation = luminosity/126.7 if luminosity is not None else None* > ---------------- end weewx.conf excerpt > > otherwise you won't get data from a solar sensor displayed > Good luck - and have fun ! > > On 21.03.2021 14:48, Auchtermuchty Weather wrote: > > Thanks, I knew I'd seen something about this but forgot about the other > forum. > > That worked, but what a horrible method! A better way (in my view) would > be it picks up the network itself and has an inbuilt HTTP server for any > further configuration. I guess the prevalence of mobile devices is > affecting things, adversely IMHO - a mobile device is perfectly capable of > picking up data from an IP address... > > I've given it a static IP, cycled the power and it's back on the network > with the right static IP. The new IP also shows in WS View and on looking > though the screens in WS View it looks like I have some new data to play > with, plus humidity looks about right so I imagine the dew point will be. > > Now to implement connecting to it from WeeWx... > > On Sunday, 21 March 2021 at 13:12:59 UTC [email protected] wrote: > >> You can go through the instructions/suggestions posted at >> https://www.wxforum.net/index.php?topic=41575.0 >> this works in 99.5% of all cases so far. 😁 >> From what I read, your main issue might be >> that you probably use the wrong app (probably wrongly stated in the >> reseller manual) - you have to use the WSView app - WS Tools won't work for >> that purpose >> On 21.03.2021 13:37, Auchtermuchty Weather wrote: >> >> PS I've tried a reset just now, no idea at what point in the flashing I >> should let the button go but again I have both sensors connected but it's >> not connecting to the WiFi >> >> On Sunday, 21 March 2021 at 12:25:13 UTC Auchtermuchty Weather wrote: >> >>> >>> GW1000 - the tiny little thing with blue LEDs. Certainly not a console. >>> On Sunday, 21 March 2021 at 12:18:10 UTC [email protected] wrote: >>> >>>> Do you have a gateway device GW1000 or a console? >>>> >>>> On Sun, 21 Mar 2021 at 12:03, Auchtermuchty Weather <[email protected]> >>>> wrote: >>>> >>>>> So my WH2650 clone eventually arrived and is installed in the garden. >>>>> However can't get the base station to connect to my router. I've >>>>> plugged >>>>> it in, it's connected to indoor & outdoor sensors but the WiFi light >>>>> continues to flash rapidly. I've turned off the 5GHz Wifi, I've got the >>>>> WS >>>>> Tool app. And the App won't let me put the SSID in either. If just has >>>>> '<Unknown SSID>'. >>>>> >>>>> However I see what is meant by better sensors etc. >>>>> >>>>> Should have done this bit before I turned off the old one. >>>>> >>>> -- >>>>> You received this message because you are subscribed to the Google >>>>> Groups "weewx-user" group. >>>>> To unsubscribe from this group and stop receiving emails from it, send >>>>> an email to [email protected]. >>>>> To view this discussion on the web visit >>>>> https://groups.google.com/d/msgid/weewx-user/73707865-d69c-4a18-8709-02142dae07dbn%40googlegroups.com >>>>> >>>>> <https://groups.google.com/d/msgid/weewx-user/73707865-d69c-4a18-8709-02142dae07dbn%40googlegroups.com?utm_medium=email&utm_source=footer> >>>>> . >>>>> >>>> -- >> You received this message because you are subscribed to the Google Groups >> "weewx-user" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> >> To view this discussion on the web visit >> https://groups.google.com/d/msgid/weewx-user/8a2e3a7e-399d-41e4-8dbc-9cbcedea100dn%40googlegroups.com >> >> <https://groups.google.com/d/msgid/weewx-user/8a2e3a7e-399d-41e4-8dbc-9cbcedea100dn%40googlegroups.com?utm_medium=email&utm_source=footer> >> . >> >> >> -- > You received this message because you are subscribed to the Google Groups > "weewx-user" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > > To view this discussion on the web visit > https://groups.google.com/d/msgid/weewx-user/44dbd146-5a51-486a-a592-aa6bd021dec9n%40googlegroups.com > > <https://groups.google.com/d/msgid/weewx-user/44dbd146-5a51-486a-a592-aa6bd021dec9n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > > -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/weewx-user/3397db70-bad2-4674-b1f0-afd71e884284n%40googlegroups.com.
