I am not sure what is going on. I can still only capture wind speed and direction.
the data is there in the log but it won't capture it. I pointed everything back to my AIR and it worked. Changed it back to the tempest and alli get is N/A attached my weewx.conf incase someone notices a typo. On Sat, May 1, 2021 at 6:41 PM vince <[email protected]> wrote: > I don't see it, but there has to be a typo in weewx.conf someplace. > > My old Tempest weewx.conf is at > https://community.weatherflow.com/t/weewx-udp-driver-for-weatherflow-station/283/189 > if you want to take a look there. Of course you'll have to edit in your > serial numbers for your sensor. > > On Saturday, May 1, 2021 at 2:02:40 PM UTC-7 [email protected] wrote: > >> >> I am using this udp driver" >> https://github.com/captain-coredump/weatherflow-udp >> >> log attached >> >> snip from log: >> May 1 17:01:19 raspberrypi weewxd: weatherflowudp: MainThread: raw >> packet: {'fs': [1, 0, 15675411, 524288], 'seq': 837, 'firmware_revision': >> '169', 'timestamp': 1619902878, 'serial_number': 'HB-00012441', 'uptime': >> 8414, 'reset_flags': 'BOR,PIN,POR', 'mqtt_stats': [49, 0], 'rssi': -25, >> 'type': 'hub_status', 'radio_stats': [5, 1, 0, 3, 0]} >> May 1 17:01:20 raspberrypi weewxd: weatherflowudp: MainThread: raw >> packet: {'firmware_revision': 134, 'timestamp': 1619902879, 'voltage': >> 2.585, 'rssi': -68, 'hub_sn': 'HB-00012441', 'uptime': 19985, 'hub_rssi': >> -60, 'sensor_status': 0, 'debug': 0, 'serial_number': 'ST-00021019', >> 'type': 'device_status'} >> May 1 17:01:20 raspberrypi weewxd: weatherflowudp: MainThread: raw >> packet: {'firmware_revision': 134, 'serial_number': 'ST-00021019', 'type': >> 'obs_st', 'obs': [[1619902879, 0.54, 3.03, 5.93, 215, 3, 967.62, 16.41, >> 29.09, 63223, 2.87, 527, 0.0, 0, 0, 0, 2.585, 1]], 'hub_sn': 'HB-00012441'} >> May 1 17:01:22 raspberrypi weewxd: weatherflowudp: MainThread: raw >> packet: {'serial_number': 'ST-00021019', 'type': 'rapid_wind', 'ob': >> [1619902881, 2.24, 196], 'hub_sn': 'HB-00012441'} >> May 1 17:01:22 raspberrypi weewx[1884] INFO weewx.restx: MQTT: Published >> record 2021-05-01 17:01:21 EDT (1619902881) >> May 1 17:01:25 raspberrypi weewxd: weatherflowudp: MainThread: raw >> packet: {'serial_number': 'ST-00021019', 'type': 'rapid_wind', 'ob': >> [1619902884, 2.24, 205], 'hub_sn': 'HB-00012441'} >> May 1 17:01:25 raspberrypi weewx[1884] INFO weewx.restx: MQTT: Published >> record 2021-05-01 17:01:24 EDT (1619902884) >> May 1 17:01:28 raspberrypi weewxd: weatherflowudp: MainThread: raw >> packet: {'serial_number': 'ST-00021019', 'type': 'rapid_wind', 'ob': >> [1619902887, 1.88, 248], 'hub_sn': 'HB-00012441'} >> May 1 17:01:28 raspberrypi weewx[1884] INFO weewx.restx: MQTT: Published >> record 2021-05-01 17:01:27 EDT (1619902887) >> May 1 17:01:29 raspberrypi weewxd: weatherflowudp: MainThread: raw >> packet: {'fs': [1, 0, 15675411, 524288], 'seq': 838, 'firmware_revision': >> '169', 'timestamp': 1619902888, 'serial_number': 'HB-00012441', 'uptime': >> 8424, 'reset_flags': 'BOR,PIN,POR', 'mqtt_stats': [49, 0], 'rssi': -26, >> 'type': 'hub_status', 'radio_stats': [5, 1, 0, 3, 0]} >> May 1 17:01:31 raspberrypi weewxd: weatherflowudp: MainThread: raw >> packet: {'serial_number': 'ST-00021019', 'type': 'rapid_wind', 'ob': >> [1619902890, 2.64, 240], 'hub_sn': 'HB-00012441'} >> May 1 17:01:31 raspberrypi weewx[1884] INFO weewx.restx: MQTT: Published >> record 2021-05-01 17:01:30 EDT (1619902890) >> >> >> On Sat, May 1, 2021 at 4:24 PM vince <[email protected]> wrote: >> >>> Without seeing your logs, it's uncertain what you're seeing. >>> We also don't know which driver of the many WF drivers to pick from you >>> are running. >>> >>> The FAQ >>> <https://github.com/weewx/weewx/wiki/faq-how-to-report-a-problem> has >>> more info on how to give us enough information to understand your system. >>> >>> It is almost certain that you have a typo in your sensor_map especially >>> since you see rapid_wind but not anything obs_st being recorded. >>> >>> That said, you might want to run my standalone WF UDP listener (link) >>> <https://github.com/vinceskahan/weatherflow-udp-listener> with the >>> --raw --debug flags to see what your Hub is emitting in its UDP. The >>> github page has too much info on how to run the listener to repeat here. >>> >>> On Saturday, May 1, 2021 at 1:10:57 PM UTC-7 [email protected] wrote: >>> >>>> I recently upgraded to the Tempest. I updated my weewx.conf file for >>>> the new sensor map. >>>> >>>> The only thing that is recording is the wind speed and direction. >>>> >>>> I checked the log and the packets are there. >>>> >>>> When i revert back to my AIR it works fine. >>>> >>>> Any help would be appreciated. >>>> >>>> [[sensor_map]] >>>> outTemp = air_temperature.ST-00021019.obs_st >>>> outHumidity = relative_humidity.ST-00021019.obs_st >>>> pressure = station_pressure.ST-00021019.obs_st >>>> lightning_strike_count = lightning_strike_count.ST-00021019.obs_st >>>> lightning_distance = lightning_strike_avg_distance.ST-00021019.obs_st >>>> outTempBatteryStatus = battery.ST-00021019.obs_st >>>> windSpeed = wind_speed.ST-00021019.rapid_wind >>>> windDir = wind_direction.ST-00021019.rapid_wind >>>> luxXXX = illuminance.ST-00021019.obs_st >>>> UV = uv.ST-00021019.obs_st >>>> rain = rain_accumulated.ST-00021019.obs_st >>>> windBatteryStatus = battery.ST-00021019.obs_st >>>> radiation = solar_radiation.ST-00000025.obs_st >>>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "weewx-user" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/weewx-user/5f4b21b3-c704-4e41-954a-5fc6a6fd63aen%40googlegroups.com >>> <https://groups.google.com/d/msgid/weewx-user/5f4b21b3-c704-4e41-954a-5fc6a6fd63aen%40googlegroups.com?utm_medium=email&utm_source=footer> >>> . >>> >> -- > You received this message because you are subscribed to the Google Groups > "weewx-user" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/weewx-user/8fd3e21f-6dc0-4659-adad-8c7c21627ec2n%40googlegroups.com > <https://groups.google.com/d/msgid/weewx-user/8fd3e21f-6dc0-4659-adad-8c7c21627ec2n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/weewx-user/CABn15dZZd-JV%3DNXcFzKRx7ZJfQjnHEyPTZkpQvjBBifOY3KnjA%40mail.gmail.com.
weewx.conf.5.1.21
Description: Binary data
