Ah! Found it. Page 126, Notification message variables. Reading now. Vielen Danke. Bruce
-----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Sent: Wednesday, April 13, 2005 2:52 AM To: [email protected] Subject: Antwort: RE: [WhatsUp Forum] APC UPS Help Requested Bruce, Did you set %PassiveMonitor.Payload.* in your notification email? You can check the information provided and often a %PassiveMonitor.Payload.TrapName will do this job. Regards, Daniel -- Daniel Blaser System Engineer ISP Abt. Lie-Comtel Tel: +423 / 236 17 60 Liechtensteinische Kraftwerke Fax: +423 / 236 17 41 Im alten Riet 17, 9494 Schaan Web: http://www.lkw.li "Meyer, Bruce" <[EMAIL PROTECTED]> Gesendet von: [EMAIL PROTECTED] 11.04.2005 15:27 Bitte antworten an [email protected] An "'[email protected]'" <[email protected]> Kopie Thema RE: [WhatsUp Forum] APC UPS Help Requested Thanks Kent, I followed your instructions and it returned: enterprises.318.1.3.2.7 I put that into the Device Object ID Property, and turned on Auto-Discovery, and did an SNMP smart scan. It didn't return anything new. I guess the problem is, maybe I am trying to do something that WUG doesn't do., I don't know. What would be nice, is if any of the alarms that the AUPC software normally reports on (This is being set on the IP address of a network Monitoring card I put in the back of the UPS) that WUG will not just alert (which I assume it does when I set SNMP Traps to ANY) rather I would like an intelligent alert like, 'APC went on Battery, or Over/Undervoltage etc.' I was hoping to use SNMP in WUG to intelligently, report the UPS status. I already have the UPS configured to send out emails, but should that email fail to be sent for who know what reasons, perhaps the SNMP part of WUG would take over. Also it would be nice to select SNMP and monitor voltage or other things that SNMP can monitor on a UPS. Do you know if this is covered in a book, or web site somewhere? --Bruce -----Original Message----- From: Kent, Robert [mailto:[EMAIL PROTECTED] Sent: Saturday, April 09, 2005 1:43 PM To: [email protected] Subject: RE: [WhatsUp Forum] APC UPS Help Requested If it's the number I think you're looking for, you can use the MIB browser that comes with WhatsUp to query the device directly. In the "net tool" (tools > net tool) click on the SNMP tab, then browse to the SysObjectID node (What = 1.3.6.1.2.1.1.2)and do a query (click start). What returns is what to put into the Device Object ID property to allow WhatsUp to correctly identify the device when it does an auto-discovery. And as far as I know, it's not used for anything else other than auto-discovery. R Kent UITS Network Engineering University of CT -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Meyer, Bruce Sent: Friday, April 08, 2005 4:41 PM To: '[email protected]' Subject: [WhatsUp Forum] APC UPS Help Requested I have run the util that imports MIBs on the MIB files that came with my APC CD. I have configured the environment management module on the UPS to the correct community name, with READ only access, and the WUG server IP address. I have set up Whats up gold to monitor any traps from the device. I have then clicked on SNMP icon, and entered the community name. The Device Object ID however has me stymied. How do I figure out what to enter here, short of doing a smart scan of that subnet which I would strongly prefer to not do. Thanks for any help offered. Bruce D. Meyer Please visit http://www.ipswitch.com/support/mailing-lists.html to be removed from this list. An Archive of this list is available at: http://www.mail-archive.com/whatsup_forum%40list.ipswitch.com/ Please visit http://www.ipswitch.com/support/mailing-lists.html to be removed from this list. An Archive of this list is available at: http://www.mail-archive.com/whatsup_forum%40list.ipswitch.com/ Please visit http://www.ipswitch.com/support/mailing-lists.html to be removed from this list. An Archive of this list is available at: http://www.mail-archive.com/whatsup_forum%40list.ipswitch.com/ Please visit http://www.ipswitch.com/support/mailing-lists.html to be removed from this list. An Archive of this list is available at: http://www.mail-archive.com/whatsup_forum%40list.ipswitch.com/ Please visit http://www.ipswitch.com/support/mailing-lists.html to be removed from this list. An Archive of this list is available at: http://www.mail-archive.com/whatsup_forum%40list.ipswitch.com/
