Do you like to have the spin with opposite directions on both sides of your slab ?
A horizontal mirror plane will not change the spin, but vertical mirror planes change its sign. You should look to a formal book on symmetry to know what is going on, don't use handwaving arguments. The symmetry of the atomic positions in your slab is one thing, the electronic structure another one. Ciao Gerhard DEEP THOUGHT in D. Adams; Hitchhikers Guide to the Galaxy: "I think the problem, to be quite honest with you, is that you have never actually known what the question is." ==================================== Dr. Gerhard H. Fecher Institut of Inorganic and Analytical Chemistry Johannes Gutenberg - University 55099 Mainz ________________________________________ Von: [email protected] [[email protected]]" im Auftrag von "[email protected] [[email protected]] Gesendet: Freitag, 13. Dezember 2013 18:28 An: [email protected] Betreff: Re: [Wien] Slab symmetry with SOC Dear Gerhard, Thank you for your comment. I have a feeling, that my system has an inversion symmetry from the point of view of the electronic structure. If you think of surface electronic structure and surface Brillouin zone, then the surface electronic structures on both sides of the slab must be the same, only inverted with respect to surface-Gamma. The inversion is there, because in my particular case electronic structure is the same along the magnetization-axis and along minus-magnetization-axis. In any case (with or without inversion symmetry) the 180deg rotation around the magnetization axis is one of the symmetry operations of my slab. How can I include it in my calculation using the w2web interface? Regards, Lukasz SO has no inversion symmetry Think about the spin when you apply an inversion. Ciao Gerhard DEEP THOUGHT in D. Adams; Hitchhikers Guide to the Galaxy: "I think the problem, to be quite honest with you, is that you have never actually known what the question is." ==================================== Dr. Gerhard H. Fecher Institut of Inorganic and Analytical Chemistry Johannes Gutenberg - University 55099 Mainz ________________________________________ Von: [email protected] [[email protected]]" im Auftrag von "[email protected] [[email protected]] Gesendet: Freitag, 13. Dezember 2013 18:02 An: [email protected] Betreff: Re: [Wien] Slab symmetry with SOC Dear Prof. Blaha, dear Wien2k users, I attach the most symmetric slab which I was able to produce. I try with 15 atoms in order to save time with testing, later I am planning to do a larger slab. You could see that now the surface normal is <100>, I started with <001>, but sgroup swapped axes -- but this is fine. So now the in-plane magnetization is along <001>, and it's the same as the mirror plane normal axis (becuase the space group is the 6_Pm with the unique c-axis). I believe that my system should have an inversion symmetry even with SOC. And at the same time I believe that the two surface atoms (in this case atom 1 and atom 15) should have their unique positions (they should not be merged into a single position as they would without SOC). I would appreciate the advice on how to make a spin-polarized calculation with SOC on this slab with included inversion symmetry. So far I have a mirror plane, so it would also be ok to only add a 2-fold 180deg rotation around the magnetization axis. Regards, Lukasz On 12/13/2013 11:22 AM, Peter Blaha wrote: > For a spin-polarized case you should use init_so and the program symmetso. Symmetso should give you the proper symmetries and one should use the struct file produced by symmetso. There should be a classification of each of the symmetry operations of the non-so case according to A, B or none. > > I can hardly comment on a specific feature without doing the slab myself. > > Please have a look into the lecture notes about spin-orbit coupling and the reduction of symmetry due to so (from our web-site). There is a plot and table for a small specific example. > > Hwoever, note two remarks: sgroup is completely irrelevant for this (as it does not know about spin-orbit). > > symmetso is obviously not as much tested as sgroup or symmetry. So be sure to use the latest version. > If you have doubts about symmetso, I need the struct file and the specific concerns. > > On 12/13/2013 10:00 AM, [email protected] wrote: >> Dear WIEN2k experts, >> >> Unfortunately nobody has commented on my email below. >> >> I believe that in my 15-atom Fe(001) slab, with magnetization along 100 >> and SOC included, there will be a mirror 100 plane (space group 6). >> However, I have a feeling that there are more symmetries. For example I >> have a feeling, that there should be an inversion symmetry, or at least >> that the 100 axis should be a two-fold rotation axis. I am not able to >> include these symmetries. >> >> My calculations work well with fully primitive cell, and also with space >> group 6 (actually sgroup rotates the slab, so that mirror plane becomes >> 001, but this of course does not matter). But I think that in every >> problem one should include the necessary symmetries a priori, not only to >> save time, but to avoid some spurious results. >> >> Could you please give me at least some hint? I could also send my slab if >> necessary. >> >> Regards, >> Lukasz >> >> >> >> >> >> On 12/5/2013 10:03 AM, [email protected] wrote: >> >> Dear WIEN2k experts, >> >> I am calculating 29-atom Fe(001) slab with SOC with easy axis along [100]. >> >> Without SOC one can find more symmetries, and one has only 15 inequivalent >> atoms. However, when performing the calculation with such slab the results >> are different compared to the complex calculation with "pure" slab of 29 >> atoms. I believe that the correct result in this calculation is that >> surface bands along [100] and [-100] are the same, and bands along [010] >> and [0-10] are different. So one should have 3 slightly different set of >> surface bands: along [100] (identical to [-100]), [010], and [0-10]. >> >> Of course on the opposite surfaces of the slab things will have the >> inversion symmetry. >> >> I believe that one of the programs, e.g. symmetso should in principle be >> able to find out, whether the symmetries are correct or not, and produce >> the correct struct file, which is possibly a bit more symmetric than the >> original file. >> >> Please advise. >> >> Regards, >> Lukasz >> >> >> >> >> >> _______________________________________________ >> Wien mailing list >> [email protected] >> http://zeus.theochem.tuwien.ac.at/mailman/listinfo/wien >> SEARCH the MAILING-LIST at: http://www.mail-archive.com/[email protected]/index.html -- Dr. Lukasz Plucinski _______________________________________________ Wien mailing list [email protected] http://zeus.theochem.tuwien.ac.at/mailman/listinfo/wien SEARCH the MAILING-LIST at: http://www.mail-archive.com/[email protected]/index.html _______________________________________________ Wien mailing list [email protected] http://zeus.theochem.tuwien.ac.at/mailman/listinfo/wien SEARCH the MAILING-LIST at: http://www.mail-archive.com/[email protected]/index.html _______________________________________________ Wien mailing list [email protected] http://zeus.theochem.tuwien.ac.at/mailman/listinfo/wien SEARCH the MAILING-LIST at: http://www.mail-archive.com/[email protected]/index.html
