----- Original Message ----- From: yu-ruei woo To: [email protected] Sent: Monday, September 14, 2009 1:21 AM Subject: Re: [Winpcap-users] What does WinPcap do when setting a802.11wireless NIC into promiscuous mode?
Hi, I've checked that OID_GEN_CURRENT_PACKET_FILTER is supported in NDIS5 and NDIS_PACKET_TYPE_PROMISCUOUS an available filter. So it should be OK to let WinPcap put my WLAN NIC in promiscuous mode on Windows XP. But when I configure the WLAN NIC into promiscuous mode (using WireShark) and press start, a dialog pops up with error message: The capture session could not be initiated (failed to set hardware filter to promiscuous mode). This is because WinPcap tries to set the current packet filter to NDIS_PACKET_TYPE_PROMISCUOUS, but the underlying miniport controlling your wireless card fails the request. There is nothing that WinPcap can do for that. Does it make any sense to you? Have a nice day GV Would you give me a suggestion? Thanks. Haich On Tue, Sep 1, 2009 at 11:14 PM, Gianluca Varenni <[email protected]> wrote: What you are reading is the documentation for an NDIS 6.0 driver. WinPcap is still an NDIS 5.x one, so the NDIS_PACKET_TYPE_802_11_xxxx filters are not usable from WinPcap. I don't know exactly what the NDIS 5x <--> 6.0 thunking layer does when you set the promiscuous mode, however. GV ----- Original Message ----- From: yu-ruei woo To: [email protected] Sent: Monday, August 31, 2009 11:10 PM Subject: Re: [Winpcap-users] What does WinPcap do when setting a 802.11wireless NIC into promiscuous mode? Hi, After tracing the source code, I found that in PacketSetHwFilter, you set the packet filter NDIS_PACKET_TYPE_PROMISCUOUS is true. Otherwise the packet filter is set to NDIS_PACKET_TYPE_ALL_LOCAL. In the WDK documentation, it says: It is only valid for the miniport driver to enable the NDIS_PACKET_TYPE_PROMISCUOUS, NDIS_PACKET_TYPE_802_11_PROMISCUOUS_MGMT, or NDIS_PACKET_TYPE_802_11_PROMISCUOUS_CTRL packet filters if the driver is operating in Network Monitor (NetMon) mode. But in the source code, I can't find any request to the driver that sets its operation mode to NetMon mode. So I think setting promiscuous mode in WireShard will have to effect on the NIC if the NIC driver follows the WDK documentation. Is that right? Best regards, Haich On Tue, Sep 1, 2009 at 10:49 AM, yu-ruei woo <[email protected]> wrote: Hi,I am recently modifying a WLAN driver such that it can receive 802.11 packets without filtering packets destined to other STA in the same BSS while keep the connection with the BSS. I've tried the promiscuous mode, but I found that no OID is set to the WLAN driver to notify the driver that it should now operate in promiscuous mode.I would like to know what does WinPcap do when setting a WLAN NIC into promiscuous receiving mode. Specifically, how does WinPcap notify the WLAN NIC that it should operate in promiscuous mode.Best regards,Haich -------------------------------------------------------------------------- _______________________________________________ Winpcap-users mailing list [email protected] https://www.winpcap.org/mailman/listinfo/winpcap-users _______________________________________________ Winpcap-users mailing list [email protected] https://www.winpcap.org/mailman/listinfo/winpcap-users ------------------------------------------------------------------------------ _______________________________________________ Winpcap-users mailing list [email protected] https://www.winpcap.org/mailman/listinfo/winpcap-users
_______________________________________________ Winpcap-users mailing list [email protected] https://www.winpcap.org/mailman/listinfo/winpcap-users
