I wasn't clear in the previous email, I'm only seeing ICMP requests and not answers so no traffic through the tunnel. Also, I have not setup forwarding to another interface, maybe that's the next step for a road-warrior OpenVPN-like setup, but at the moment I'm keeping things simple and I'm just trying to figure out how to have an internal private network only. As for the ports, the different ports per host is silly but I needed that because 3 of my hosts are under the same Wi-Fi and I needed to open different ports in the router to forward traffic to the right devices easily.

This is the output of the command requested:

rpi3-two pi # tcpdump -ni any icmp
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on any, link-type LINUX_SLL (Linux cooked), capture size 262144 bytes 10:35:02.177750 IP 10.0.0.3 > 10.0.0.1: ICMP echo request, id 25708, seq 1, length 64 10:35:03.232761 IP 10.0.0.3 > 10.0.0.1: ICMP echo request, id 25708, seq 2, length 64 10:35:04.272760 IP 10.0.0.3 > 10.0.0.1: ICMP echo request, id 25708, seq 3, length 64 10:35:05.312754 IP 10.0.0.3 > 10.0.0.1: ICMP echo request, id 25708, seq 4, length 64 10:35:06.352767 IP 10.0.0.3 > 10.0.0.1: ICMP echo request, id 25708, seq 5, length 64 10:35:07.392772 IP 10.0.0.3 > 10.0.0.1: ICMP echo request, id 25708, seq 6, length 64 10:35:08.432740 IP 10.0.0.3 > 10.0.0.1: ICMP echo request, id 25708, seq 7, length 64 10:35:09.472758 IP 10.0.0.3 > 10.0.0.1: ICMP echo request, id 25708, seq 8, length 64 10:35:10.512756 IP 10.0.0.3 > 10.0.0.1: ICMP echo request, id 25708, seq 9, length 64 10:35:11.552763 IP 10.0.0.3 > 10.0.0.1: ICMP echo request, id 25708, seq 10, length 64 10:35:12.592774 IP 10.0.0.3 > 10.0.0.1: ICMP echo request, id 25708, seq 11, length 64 10:35:13.632778 IP 10.0.0.3 > 10.0.0.1: ICMP echo request, id 25708, seq 12, length 64 10:35:14.672774 IP 10.0.0.3 > 10.0.0.1: ICMP echo request, id 25708, seq 13, length 64 10:35:15.712755 IP 10.0.0.3 > 10.0.0.1: ICMP echo request, id 25708, seq 14, length 64 10:35:16.752756 IP 10.0.0.3 > 10.0.0.1: ICMP echo request, id 25708, seq 15, length 64
^C
15 packets captured
15 packets received by filter
0 packets dropped by kernel

This was run from a Raspberry Pi. I only have requests to 10.0.0.1 but no answer, while on 10.0.0.4 (my laptop) I get:

clevo-W230SD riccardo # tcpdump -ni any icmp
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on any, link-type LINUX_SLL (Linux cooked), capture size 262144 bytes 11:17:04.666013 IP 10.0.0.4 > 10.0.0.1: ICMP echo request, id 3840, seq 1, length 64 11:17:04.785000 IP 10.0.0.1 > 10.0.0.4: ICMP echo reply, id 3840, seq 1, length 64 11:17:05.667080 IP 10.0.0.4 > 10.0.0.1: ICMP echo request, id 3840, seq 2, length 64 11:17:05.808343 IP 10.0.0.1 > 10.0.0.4: ICMP echo reply, id 3840, seq 2, length 64 11:17:06.668457 IP 10.0.0.4 > 10.0.0.1: ICMP echo request, id 3840, seq 3, length 64 11:17:06.832267 IP 10.0.0.1 > 10.0.0.4: ICMP echo reply, id 3840, seq 3, length 64 11:17:07.670317 IP 10.0.0.4 > 10.0.0.1: ICMP echo request, id 3840, seq 4, length 64 11:17:07.820143 IP 10.0.0.1 > 10.0.0.4: ICMP echo reply, id 3840, seq 4, length 64

As it should be, I get replies on this host.

I must repeat that "sometimes" also 10.0.0.3 works, so I'd exclude a firewall/pubkeys configuration error. Without touching it it breaks, though. Last time it worked I let it ping for hours at a fast pace just to keep it working. I then stopped to ping and a certain amount of time later I tried again and the wg0 interface wasn't working anymore.

Great WireGuard guide on your blog by the way.
_______________________________________________
WireGuard mailing list
WireGuard@lists.zx2c4.com
https://lists.zx2c4.com/mailman/listinfo/wireguard

Reply via email to