| Da quello che abbiamo potuto vedere la cosa funziona così, quando il router non ha nessuna configurazione nella memoria esso pesca la configurazione dalla scheda e se la memorizza, nei successivi avvii non fa altro che confrontare i parametri della scheda con quelli memorizzati.. ATTENZIONE: Se modifica i parametri memorizzati il router scriverà i nuovi parametri sulla scheda e voi avrete perso tutte le configurazioni (ci è successo a noi :P) Vi allego l'intero output del boot preso da seriale |
CFE version 1.0.37-3.4 for BCM96348 (32bit,SP,BE) Build Date: mar gen 24 09:26:30 CET 2006 ([email protected]) Copyright (C) 2003,2004,2005 Telsey Telecommunications.
Boot Address 0xbfc00000 Initializing Arena. Initializing Devices. Parallel flash device: name MX29LV640T, id 0x22c9, size 8192KB Auto-negotiation timed-out 10 MB Half-Duplex (assumed) Check consistency for image tag [1]: Found good image at partition [1] Check consistency for image tag [2]: Found good image at partition [2] CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz Total memory: 16777216 bytes (16MB) Total memory used by CFE: 0x80401000 - 0x80526D90 (1203600) Initialized Data: 0x8041E440 - 0x80420270 (7728) BSS Area: 0x80420270 - 0x80424D90 (19232) Local Heap: 0x80424D90 - 0x80524D90 (1048576) Stack Area: 0x80524D90 - 0x80526D90 (8192) Text (code) segment: 0x80401000 - 0x8041E440 (119872) Boot area (physical): 0x00527000 - 0x00567000 Relocation Factor: I:00000000 - D:00000000 Board IP address : 192.168.1.1 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Boot image (0=latest, 1=previous) : 0 Board Id Name : MAGIC Psi size in KB : 24 Number of MAC Addresses (1-32) : 8 Base MAC Address : 00:03:6f:1e:1d:90 Ethernet PHY Type : Internal Memory size in MB : 16 mac server test........................ ### ### Not default mac address ### 00 03 6f 1e 1d 90 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 Booting from latest image (0xc0000000) ... Code Address: 0x80010000, Entry Address: 0x80191018 Decompression OK! Entry at 0x80191018 Closing network. Starting program at 0x80191018 Linux version 2.6.8.1 (car...@carpao_lab) (gcc version 3.4.2) #1 Fri Aug 4 17:38:11 CEST 2006 Parallel flash device: name MX29LV640T, id 0x22c9, size 8192KB Total Flash size: 8192K with 135 sectors MAGIC prom init CPU revision is: 00029107 Determined physical RAM map: memory: 00fa0000 @ 00000000 (usable) On node 0 totalpages: 4000 DMA zone: 4000 pages, LIFO batch:1 Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 Built 1 zonelists Kernel command line: root=31:0 ro noinitrd brcm mips: enabling icache and dcache... Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes. Primary data cache 8kB 2-way, linesize 16 bytes. PID hash table entries: 64 (order 6: 512 bytes) Using 128.000 MHz high precision timer. Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 14076k/16000k available (1328k kernel code, 1904k reserved, 207k data, 72k init, 0k highmem) Calibrating delay loop... 254.77 BogoMIPS Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Checking for 'wait' instruction... unavailable. NET: Registered protocol family 16 Can't analyze prologue code at 8015aa24 PPP generic driver version 2.4.2 NET: Registered protocol family 24 Using noop io scheduler bcm963xx_mtd driver v1.0 bcm963xx_mtd: rootfs_addr = 0xBF800100, kernel_addr = 0xBFAC1100 brcmboard: brcm_board_init entry Confirm button interrupt has been configured bcm963xx_serial driver v2.0 NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 512 bind 1024) NET: Registered protocol family 1 NET: Registered protocol family 17 Ebtables v2.0 registered NET: Registered protocol family 8 NET: Registered protocol family 20 802.1Q VLAN Support v1.8 Ben Greear <[email protected]> All bugs added by David S. Miller <[email protected]> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 72k freed init started: BusyBox v1.00 (2006.08.04-15:44+0000) multi-call binary Algorithmics/MIPS FPU Emulator v1.5 BusyBox v1.00 (2006.08.04-15:44+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... atmapi: module license 'Proprietary' taints kernel. blaadd: blaa_detect entry adsl: adsl_init entry Broadcom BCMPROCFS v1.0 initialized Broadcom BCM6348B0 Ethernet Network Device v0.3 Aug 4 2006 17:36:49 Config Internal PHY Through MDIO BCM63xx_ENET: Auto-negotiation timed-out BCM63xx_ENET: 10 MB Half-Duplex (assumed) eth0: MAC Address: 00:03:6F:1E:1D:90 Broadcom BCM6348B0 Ethernet Network Device v0.3 Aug 4 2006 17:36:49 Config External PHY Through MDIO mii_init: mii hardware reset BCM63xx_ENET: Auto-negotiation timed-out BCM63xx_ENET: 10 MB Half-Duplex (assumed) eth1: MAC Address: 00:03:6F:1E:1D:91 Telsey BCM6348B0 USB Network Device v0.4 Aug 4 2006 17:36:52 usb0: MAC Address: 00 03 6F 1E 1D 92 usb0: Host MAC Address: 00 03 6F 1E 1D 93 MAGIC USB configuration Telsey smart card: tda8007_module_init tda8007: Found TDA 8007BHL/C2 loading Broadcom WIFI module PCI: Setting latency timer of device 0000:00:01.0 to 64 PCI: Enabling device 0000:00:01.0 (0004 -> 0006) wl0: Broadcom BCM4318 802.11 Wireless Controller 3.131.35.0.cpe0.0 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered wlctl: wlctl: smartcardmngr:Initializing SmartCardMngr smartcardmngr:SMART CARD INSERTED Answer To Reset: TS = 3b T0 = ff TA1 = 94 TB1 = 00 TC1 = ff TD1 = 80 TD2 = b1 TA3 = fe TB3 = 45 TD3 = 1f TA4 = 03 HB 1 = 00 Status information the end of the historical bytes. HB 2 = 68 Pressuing data object of length 8 HB 3 = d2 HB 4 = 76 HB 5 = 00 HB 6 = 00 HB 7 = 28 HB 8 = fe HB 9 = 05 HB10 = 22 HB11 = 31 HB12 = 80 HB13 = 00 HB14 = 90 HB15 = 00 TCK = 1e sc_connect_card: _sc_parse_atr prima sc_connect_card: _sc_parse_atr dopo sc_connect_card ctx->card_drivers[0]=MICARDO 2.1 mcrd_init exiting smartcardmngr:isMyCard? smartcardmngr:my card serial number : BE:80:05:FD:85:0B:EF:6A:00:FF:00:10 smartcardmngr:inserted card serial number: BE:80:05:FD:85:0B:EF:6A:00:FF:00:10 smartcardmngr:IT'S MY CARD. SAVE A BACKUP COPY OF CURRENT CONFIGURATION smartcardmngr:execute a backup on smartcard smartcardmngr:board md5 : A3:6A:26:B2:61:91:3C:B4:04:19:99:70:7F:2C:9D:25 smartcardmngr:smartcard md5: A3:6A:26:B2:61:91:3C:B4:04:19:99:70:7F:2C:9D:25 smartcardmngr:board and smartcard configurations are the same, do not save anything BcmAdsl_Initialize=0xC0057228, g_pFnNotifyCallback=0xC006B564 AdslCoreHwReset: AdslOemDataAddr = 0xA0FFB21C dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered ip_tables: (C) 2000-2002 Netfilter core team ip_conntrack version 2.1 (125 buckets, 0 max) - 368 bytes per conntrack ip_conntrack_pptp version 2.1 loaded ip_nat_pptp version 2.0 loaded ip_conntrack_h323: init ip_nat_h323: initialize the module! insmod: cannot open module `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/ip_conntrack_ipsec.ko': No such file or directory insmod: cannot open module `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/ip_nat_ipsec.ko': No such file or directory ==> Bcm963xx Software Version: 3.4.19.A2pB019b8.d16m <== device usb0 entered promiscuous mode bcm63xxenet: Command 35318 not supported. app: configure ethernet eth0 speed failed. bcm63xxenet: Command 35317 not supported. app: configure ethernet eth0 duplex type failed. br0: port 1(usb0) entering learning state br0: topology change detected, propagating br0: port 1(usb0) entering forwarding state device eth0 entered promiscuous mode br0: port 2(eth0) entering learning state br0: topology change detected, propagating br0: port 2(eth0) entering forwarding state bcm63xxenet: Command 35318 not supported. app: configure ethernet eth1 speed failed. bcm63xxenet: Command 35317 not supported. app: configure ethernet eth1 duplex type failed. device eth1 entered promiscuous mode br0: port 3(eth1) entering learning state br0: topology change detected, propagating br0: port 3(eth1) entering forwarding state Setting SSID "Alice-*********" Setting SSID "Guest" Setting country code using abbreviation: "IT" wlctl: Unsupported wl0 current channel 11 device wl0 entered promiscuous mode br0: port 4(wl0) entering learning state br0: topology change detected, propagating br0: port 4(wl0) entering forwarding state device wl0.1 entered promiscuous mode ManageableDeviceSize object not found in PSI pvc2684d: Interface "nas_8_35" created sucessfully pvc2684d: Communicating over ATM 0.8.35, encapsulation: LLC device nas_8_35 entered promiscuous mode br0: port 6(nas_8_35) entering learning state br0: topology change detected, propagating br0: port 6(nas_8_35) entering forwarding state pvc2684d: Interface "nas_8_36" created sucessfully pvc2684d: Communicating over ATM 0.8.36, encapsulation: LLC device usb0 left promiscuous mode br0: port 1(usb0) entering disabled state device usb0 entered promiscuous mode br0: port 1(usb0) entering learning state br0: topology change detected, propagating br0: port 1(usb0) entering forwarding state device eth1 left promiscuous mode br0: port 3(eth1) entering disabled state device eth1 entered promiscuous mode br0: port 3(eth1) entering learning state br0: topology change detected, propagating br0: port 3(eth1) entering forwarding state device eth0 left promiscuous mode br0: port 2(eth0) entering disabled state device eth0 entered promiscuous mode br1: port 1(eth0) entering learning state br1: topology change detected, propagating br1: port 1(eth0) entering forwarding state device nas_8_36 entered promiscuous mode br1: port 2(nas_8_36) entering learning state br1: topology change detected, propagating br1: port 2(nas_8_36) entering forwarding state Cert File empty Cert File empty resetEth(): eth0 resetEth(): eth1 BcmTermMngrInit TermMngr::configRestore() TermMngr::configRestore() 0 entries in psi, status = 3 TermMngr::connectionNameSet() TermMngr::connectionNameSet() service = User Session, wan name = ppp_8_35_2,vpi = 8, vci = 35, conId = 2 TermMngr::wanStart() Start = 1, bStarted = 0,term natted num = 0, vpi = 8, vci = 35 TermMngr::sizeListTermNatted 0 bStart 1 m_bWanStarted 0 BcmWiseconMngrInit WiseconMngr::init() WiseconMngr::wiseconServerStart() wisecon-server main BcmWiFiRepeaterMngrInit WsFsm::Fsm(): WsFsm::setClientMac(): macAddr = sntp: host not found WiFiRepeaterMngr::init() Write in a subdirectory pid for wifi repeater process Login: BcmWan_startInterface: vpi = 8, vci = 35, conId = 1 pWanId status = 0 BcmWan_startInterface: vpi = 8, vci = 36, conId = 1 pWanId status = 0 br1: port 1(eth0) entering disabled state br0: port 3(eth1) entering disabled state br0: port 1(usb0) entering disabled state Setting SSID "Alice-********" Setting SSID "Guest" br0: port 4(wl0) entering disabled state Setting country code using abbreviation: "IT" wlctl: Unsupported wl0 current channel 11 br0: port 4(wl0) entering learning state br0: topology change detected, propagating br0: port 4(wl0) entering forwarding state device wl0 is already a member of a bridge; can't enslave it to bridge br0. device wl0.1 is already a member of a bridge; can't enslave it to bridge br0. WsFsm::setWlVar(): WsFsm::setWepKey(): wepKey = *********** (li abbiamo cancellati tanto per) WsFsm::setWepKey(): wepHexKey = **************** WsFsm::setWpaKey(): wpaKey = ************************* WsFsm::saveWlEncryptionConfig(): WsFsm::saveWlEncryptionConfig(): Wpa open Wep enabled WsFsm::getAuthMode: open WsFsm::getWepMode: enabled WsFsm::setEncryptionFlag(): set m_bEncryption = 1 WsFsm::saveWlMacFilterConfig(): WsFsm::saveWlMacFilterConfig disabled WsFsm::getMacFilterMode: disabled WsFsm::setMacFilterFlag(): set m_bMacFilter = 0 WsFsm::setLedState(): WsFsm::setIdRequestAuthentication(): 0 Ws::Ws(): set m_uiKeyNumPressed = 0 Password: Login incorrect. Try again. Login:
Il giorno 26/mag/09, alle ore 15:06, Emanuele Fia ha scritto: della smart card penso .... così se si rompe il router mantendendo la stessa smart non bisogna cambiare impostazioni sul pc ... |
_______________________________________________ Wireless mailing list [email protected] http://ml.ninux.org/mailman/listinfo/wireless
