This config is actually off of a Cisco 2610. This router has a Dual WIC and a Single WIC. The Single was the default gateway to another location that housed our internet connection. The dual WIC was later used for a bonded T1 solution. We had 4 bonded T1s before we switched to fiber.
I have several more configs if you need. Thanks, Eric ----Start----- version 12.2 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname PDS_Router ! enable secret 5 REMOVED enable password REMOVED ! ip subnet-zero ! ! no ip domain-lookup ! call rsvp-sync ! ! ! ! ! ! # Dual WIC Port 0/0 controller T1 0/0 framing esf linecode b8zs channel-group 0 timeslots 1-24 ! # Dual WIC Port 0/1 controller T1 0/1 framing esf linecode b8zs channel-group 0 timeslots 1-24 ! ! ! interface FastEthernet0/0 ip address REMOVED 255.255.255.224 secondary ip address REMOVED 255.255.255.224 secondary ip address REMOVED 255.255.255.0 no ip mroute-cache speed 100 full-duplex ! # WIC 0:0 - Double WIC Port 0 interface Serial0/0:0 no ip address encapsulation frame-relay IETF no keepalive ! # WIC 0:1 - Double WIC Port 1 interface Serial0/1:0 no ip address encapsulation frame-relay IETF no keepalive ! # WIC 1:0 - Single WIC card to feed remote router interface Serial0/2 description connected to Internet ip address REMOVED 255.255.255.252 ip access-group 101 in no ip unreachables no ip proxy-arp no ip mroute-cache ntp disable no fair-queue service-module t1 remote-alarm-enable ! ip classless ip route 0.0.0.0 0.0.0.0 Serial0/2 no ip http server ! access-list 101 deny udp any any eq snmp access-list 101 deny udp any any eq snmptrap access-list 101 deny tcp any any eq telnet access-list 101 deny ip 192.168.0.0 0.0.255.255 any access-list 101 deny ip 127.0.0.0 0.255.255.255 any access-list 101 deny ip 255.0.0.0 0.255.255.255 any access-list 101 deny ip 224.0.0.0 7.255.255.255 any access-list 101 deny ip host 0.0.0.0 any access-list 101 permit ip any any dialer-list 1 protocol ip permit dialer-list 1 protocol ipx permit snmp-server community REMOVED RO snmp-server enable traps tty ! dial-peer cor custom ! ! ! ! line con 0 line aux 0 line vty 0 4 password REMOVED login ! end -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of support Sent: Tuesday, September 30, 2008 1:30 PM To: WISPA General List Subject: [WISPA] Cisco 2610 Gang, OT: I need some help in setting up a T1. I have a Cisco 2610 with WIC 1 DSU T1. I am not a cisco guy. Can anyone send me to a sample config file or something? T1 is to qwest for internet access. Jason ------------------------------------------------------------------------ -------- WISPA Wants You! Join today! http://signup.wispa.org/ ------------------------------------------------------------------------ -------- WISPA Wireless List: [email protected] Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ -------------------------------------------------------------------------------- WISPA Wants You! Join today! http://signup.wispa.org/ -------------------------------------------------------------------------------- WISPA Wireless List: [email protected] Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
