I've had the opposite experience. I have Bullet2's working but when they dont I go back to Tranzeos - they always work. Are you using regular Bullets or HP's?? -RickG
On Wed, Nov 11, 2009 at 11:44 AM, Steve Barnes <[email protected]> wrote: > Marlon I have never attached a external antenna to one. I had a vendor > tell me there was a 5% drop with a external antenna. We use a Reflective > dish to increase the RSSI. I have 400+ Tranzeo sl2 and cpq19's. I have > about 10 NS2 out there. I just ordered another 15 NS2's and no more > Tranzeo's. > > The thing I like about the NS2's is the noise rejection compared to the > Tranzeo. Just Yesterday my installers were out on an install 4 mile link > clear LOS CPQ19. -69 at radio -68 at the tower but 90% retries on the > Tranzeo, best speed 800K/400K. Tried a 2nd with same issue. They came back > to office got a NS2. With the ubiquity same -69 at radio -71 at tower but > rssi of 92% and speeds went to 2048K/1024K which is what the queue is set at > on the tower. > Impressive > > Steve Barnes > RC-WiFi Wireless Internet Service > > Character cannot be developed in ease and quiet. Only through experience of > trial and suffering can the soul be strengthened, vision cleared, ambition > inspired, and success achieved. > - Helen Keller > > > -----Original Message----- > From: [email protected] [mailto:[email protected]] On > Behalf Of Robert West > Sent: Wednesday, November 11, 2009 11:17 AM > To: 'WISPA General List' > Subject: Re: [WISPA] ubiquity bullet2 > > Mine never matches. I have one I installed just the other night, one side > is stuck at -44. Reset the thing, flashed the bios again, still shows -44. > If I aim away, yeah, it changes but even if I get "close it shows -44. The > other side shows -56. It all works so what the heck. > > I'm using the new 5ghz bullets for back hauls to 5 small AP's I'm putting > in. Seem to work okay. > > > > > > -----Original Message----- > From: [email protected] [mailto:[email protected]] On > Behalf Of Marlon K. Schafer > Sent: Wednesday, November 11, 2009 10:39 AM > To: WISPA General List > Subject: [WISPA] ubiquity bullet2 > > Hi All, > > I tried my first one of these yesterday. It's hooked to an antenna that > was > > already in place so I know the old system worked though I did not check > signal levels before taking out the old SB radios (they don't give rssi > accurately anyway so there was no point). > > This new radio has an RSSI of -78 or so coming FROM the tower. AT the > tower > > we're picking up -88 or so. I turned it up to 20dB out (factory was set at > 16) and that did help a bit. > > The calculations show that I should be in the -74 to -78 range based on the > exact distance of the link. So my RSSI AT the remote end is right in > there. > > I should be seeing the same at the tower as well. > > Anyone seen these units have faulty transmitters? This is the third > ubiquity I've tried. Two PowerStations died (receive sensitivity went > dead) > > after several months. Both units at almost the exact same time. This not > giving me any comfort levels at all.... > > I know others out there are using a lot of these, are you seeing ANY > strange > > issues at all? Have you looked at the RSSI from both ends? Does it match? > > Thanks, > marlon > > > > > ---------------------------------------------------------------------------- > ---- > WISPA Wants You! Join today! > http://signup.wispa.org/ > > ---------------------------------------------------------------------------- > ---- > > WISPA Wireless List: [email protected] > > Subscribe/Unsubscribe: > http://lists.wispa.org/mailman/listinfo/wireless > > Archives: http://lists.wispa.org/pipermail/wireless/ > > > > > -------------------------------------------------------------------------------- > WISPA Wants You! Join today! > http://signup.wispa.org/ > > -------------------------------------------------------------------------------- > > WISPA Wireless List: [email protected] > > Subscribe/Unsubscribe: > http://lists.wispa.org/mailman/listinfo/wireless > > Archives: http://lists.wispa.org/pipermail/wireless/ > > > > -------------------------------------------------------------------------------- > WISPA Wants You! Join today! > http://signup.wispa.org/ > > -------------------------------------------------------------------------------- > > WISPA Wireless List: [email protected] > > Subscribe/Unsubscribe: > http://lists.wispa.org/mailman/listinfo/wireless > > Archives: http://lists.wispa.org/pipermail/wireless/ > -------------------------------------------------------------------------------- WISPA Wants You! Join today! http://signup.wispa.org/ -------------------------------------------------------------------------------- WISPA Wireless List: [email protected] Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
