No idea. ----- Original Message ----- From: "Michael Baird" <[email protected]> To: "WISPA General List" <[email protected]> Sent: Thursday, November 12, 2009 7:40 AM Subject: Re: [WISPA] ubiquity bullet2
> Marlon, > > I thought about this after you mentioned it, we are using Ubiquity on > the tower also, not MT, vendor readings will vary. > > Are you using Bullet2HP's or Bullet2M's? The M series isn't wholly G > compatible at this time. > > Regards > Michael Baird >> It's an omni... >> >> I think I'm gonna pull this out and drop in a tranzeo to see what it does >> as >> well. >> marlon >> >> ----- Original Message ----- >> From: "Michael Baird" <[email protected]> >> To: "WISPA General List" <[email protected]> >> Sent: Wednesday, November 11, 2009 8:38 AM >> Subject: Re: [WISPA] ubiquity bullet2 >> >> >> >>> Marlon, >>> >>> We've had quite a few deployed (100 or so, some for 6 months), not seen >>> a week transmitter yet, all failures were ethernet related and normally >>> out of the box they failed (1 in the field). The levels are normally >>> within 1/2 db at the tower vs. the CPE, unless there is a tilt issue (AP >>> antenna too much downtilt). >>> >>> Regards >>> Michael Baird >>> >>>> Hi All, >>>> >>>> I tried my first one of these yesterday. It's hooked to an antenna >>>> that >>>> was >>>> already in place so I know the old system worked though I did not check >>>> signal levels before taking out the old SB radios (they don't give rssi >>>> accurately anyway so there was no point). >>>> >>>> This new radio has an RSSI of -78 or so coming FROM the tower. AT the >>>> tower >>>> we're picking up -88 or so. I turned it up to 20dB out (factory was >>>> set >>>> at >>>> 16) and that did help a bit. >>>> >>>> The calculations show that I should be in the -74 to -78 range based on >>>> the >>>> exact distance of the link. So my RSSI AT the remote end is right in >>>> there. >>>> I should be seeing the same at the tower as well. >>>> >>>> Anyone seen these units have faulty transmitters? This is the third >>>> ubiquity I've tried. Two PowerStations died (receive sensitivity went >>>> dead) >>>> after several months. Both units at almost the exact same time. This >>>> not >>>> giving me any comfort levels at all.... >>>> >>>> I know others out there are using a lot of these, are you seeing ANY >>>> strange >>>> issues at all? Have you looked at the RSSI from both ends? Does it >>>> match? >>>> >>>> Thanks, >>>> marlon >>>> >>>> >>>> >>>> -------------------------------------------------------------------------------- >>>> WISPA Wants You! Join today! >>>> http://signup.wispa.org/ >>>> -------------------------------------------------------------------------------- >>>> >>>> WISPA Wireless List: [email protected] >>>> >>>> Subscribe/Unsubscribe: >>>> http://lists.wispa.org/mailman/listinfo/wireless >>>> >>>> Archives: http://lists.wispa.org/pipermail/wireless/ >>>> >>>> >>> >>> -------------------------------------------------------------------------------- >>> WISPA Wants You! Join today! >>> http://signup.wispa.org/ >>> -------------------------------------------------------------------------------- >>> >>> WISPA Wireless List: [email protected] >>> >>> Subscribe/Unsubscribe: >>> http://lists.wispa.org/mailman/listinfo/wireless >>> >>> Archives: http://lists.wispa.org/pipermail/wireless/ >>> >> >> >> >> -------------------------------------------------------------------------------- >> WISPA Wants You! Join today! >> http://signup.wispa.org/ >> -------------------------------------------------------------------------------- >> >> WISPA Wireless List: [email protected] >> >> Subscribe/Unsubscribe: >> http://lists.wispa.org/mailman/listinfo/wireless >> >> Archives: http://lists.wispa.org/pipermail/wireless/ >> > > > > -------------------------------------------------------------------------------- > WISPA Wants You! Join today! > http://signup.wispa.org/ > -------------------------------------------------------------------------------- > > WISPA Wireless List: [email protected] > > Subscribe/Unsubscribe: > http://lists.wispa.org/mailman/listinfo/wireless > > Archives: http://lists.wispa.org/pipermail/wireless/ -------------------------------------------------------------------------------- WISPA Wants You! Join today! http://signup.wispa.org/ -------------------------------------------------------------------------------- WISPA Wireless List: [email protected] Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
