Floor is -98. So, using 20dB fade margin would mean -70's is good? On Mon, Feb 1, 2010 at 10:01 PM, Jerry Richardson <[email protected]>wrote:
> I tend to use 20dB fade margin. If the floor is -80, then -60 is going > to be great. This works until you are dealing with a -60dB floor cause > -40dB is going to be too hot and overload the Rx of the radios. > > Sent Mobile > Jerry Richardson > airCloud Communications > > On Feb 1, 2010, at 5:56 PM, "RickG" <[email protected]> wrote: > > > Ya, thats what I do. I'm just concerned about what the best power > > level is? > > I hate to create a monster based on the wrong settings. > > > > On Mon, Feb 1, 2010 at 8:21 PM, Robert West <[email protected] > > >wrote: > > > >> I have a few like that. Cheap and quick for low density > >> population. Use a > >> pac grid for the backhaul and a bullet with an omni for the AP. > >> Check your > >> polarity, make sure you're on the right orientation and right > >> radio. My > >> grids are horz. Pol and the omnis, well..... Vertical of course! > >> > >> Bob- > >> > >> > >> > >> -----Original Message----- > >> From: [email protected] [mailto:wireless- > >> [email protected]] On > >> Behalf Of RickG > >> Sent: Monday, February 01, 2010 8:08 PM > >> To: WISPA General List > >> Subject: [WISPA] power > >> > >> OK, I need a little input. I've got several "poor mans repeaters" > >> around by > >> using a pair of bullets, one for backhaul and the other for the AP. > >> Today, > >> I > >> installed a Bullet on a new customer that was a stones throw away > >> from the > >> AP. At full power, he got just under 1Mbps. Turning down the power, > >> he got > >> 3Mbps+. Is turning down the power on the CPE side on a test and > >> trial basis > >> or is there some kind of method to it? > >> -RickG > >> > >> > >> > >> --- > >> --- > >> --- > >> ------------------------------------------------------------------- > >> ---- > >> WISPA Wants You! Join today! > >> http://signup.wispa.org/ > >> > >> --- > >> --- > >> --- > >> ------------------------------------------------------------------- > >> ---- > >> > >> WISPA Wireless List: [email protected] > >> > >> Subscribe/Unsubscribe: > >> http://lists.wispa.org/mailman/listinfo/wireless > >> > >> Archives: http://lists.wispa.org/pipermail/wireless/ > >> > >> > >> > >> > >> --- > >> --- > >> --- > >> --- > >> -------------------------------------------------------------------- > >> WISPA Wants You! Join today! > >> http://signup.wispa.org/ > >> > >> --- > >> --- > >> --- > >> --- > >> -------------------------------------------------------------------- > >> > >> WISPA Wireless List: [email protected] > >> > >> Subscribe/Unsubscribe: > >> http://lists.wispa.org/mailman/listinfo/wireless > >> > >> Archives: http://lists.wispa.org/pipermail/wireless/ > >> > > > > > > --- > > --- > > --- > > --- > > -------------------------------------------------------------------- > > WISPA Wants You! Join today! > > http://signup.wispa.org/ > > --- > > --- > > --- > > --- > > -------------------------------------------------------------------- > > > > WISPA Wireless List: [email protected] > > > > Subscribe/Unsubscribe: > > http://lists.wispa.org/mailman/listinfo/wireless > > > > Archives: http://lists.wispa.org/pipermail/wireless/ > > > > -------------------------------------------------------------------------------- > WISPA Wants You! Join today! > http://signup.wispa.org/ > > -------------------------------------------------------------------------------- > > WISPA Wireless List: [email protected] > > Subscribe/Unsubscribe: > http://lists.wispa.org/mailman/listinfo/wireless > > Archives: http://lists.wispa.org/pipermail/wireless/ > -------------------------------------------------------------------------------- WISPA Wants You! Join today! http://signup.wispa.org/ -------------------------------------------------------------------------------- WISPA Wireless List: [email protected] Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
