As far as I can tell, the FT command is the only way to set or query if the 991 is in split mode.
I might also mention that VFO B is not stored in memory locations. Whoever made that decision was ignorant of satellite ops. So far the "Yaesu FT-991 CAT operation Reference Book" seems accurate if not clear. On 03/03/2015 09:18 AM, Bill Somerville wrote: > On 03/03/2015 17:05, Michael Black wrote: > Hi Mike, >> Dave...do you have an FT991? If so do you care to be a tester for WJST-X >> with hamlib changes to support it? > Yaesu might lend you one if you ask nicely ;) Having said that, I would > not choose that rig for WSJT-X as it only has a 3kHz maximum Rx > bandwidth which I find disappointing for a modern DSP rig :( Maybe a > firmware update might resolve that one day. >> Mike W9MDB > 73 > Bill > G4WJS. >> -----Original Message----- >> From: Dave AA6YQ [mailto:aa...@ambersoft.com] >> Sent: Monday, March 02, 2015 1:20 PM >> To: 'WSJT software development' >> Subject: Re: [wsjt-devel] Yaesu FT-991 CAT Codes released >> >> Thanks! >> >> 73, >> >> Dave, AA6YQ >> >> -----Original Message----- >> From: Michael Black [mailto:mdblac...@yahoo.com] >> Sent: Monday, March 02, 2015 8:12 AM >> To: 'WSJT software development' >> Subject: Re: [wsjt-devel] Yaesu FT-991 CAT Codes released >> >> Yes it does. That's not the same as selecting it though. >> Can probably be emulated through swapping VFOs if needed...so check if VFO >> wanted is current vfo, swap if needed, then swap back if needed. >> >> Mike W9MDB >> >> -----Original Message----- >> From: Dave AA6YQ [mailto:aa...@ambersoft.com] >> Sent: Sunday, March 01, 2015 11:40 PM >> To: 'WSJT software development' >> Subject: Re: [wsjt-devel] Yaesu FT-991 CAT Codes released >> >> Does RI7; report which VFO is selected? >> >> 73, >> >> Dave, AA6QY >> >> -----Original Message----- >> From: Chuck Forsberg WA7KGX [mailto:c...@omen.com] >> Sent: Monday, March 02, 2015 12:29 AM >> To: WSJT software development >> Subject: Re: [wsjt-devel] Yaesu FT-991 CAT Codes released >> >> vs; returns "?;" >> >> On 03/01/2015 09:15 PM, Michael Black wrote: >>> Can you confirm that "VS;" doesn't return anything? >>> >>> >>> -----Original Message----- >>> From: Chuck Forsberg WA7KGX [mailto:c...@omen.com] >>> Sent: Sunday, March 01, 2015 11:08 PM >>> To: WSJT software development >>> Subject: Re: [wsjt-devel] Yaesu FT-991 CAT Codes released >>> >>> >>> ^C >>> c:\WSJT\wsjtx\bin>rigctl-wsjtx -vvvvvv -m134 -rcom5 -s4800 rigctl, >>> Hamlib 3.0~git Report bugs to <hamlib-develo...@lists.sourceforge.net> >>> >>> rig:rig_init called >>> yaesu: initrigs3_yaesu called >>> rig_register (121) >>> rig_register (127) >>> rig_register (110) >>> rig_register (105) >>> rig_register (106) >>> rig_register (107) >>> rig_register (109) >>> rig_register (120) >>> rig_register (101) >>> rig_register (122) >>> rig_register (123) >>> rig_register (111) >>> rig_register (115) >>> rig_register (113) >>> rig_register (114) >>> rig_register (128) >>> rig_register (131) >>> rig_register (116) >>> rig_register (134) >>> rig_register (103) >>> rig_register (124) >>> rig_register (104) >>> rig_register (125) >>> rig_register (129) >>> rig_register (132) >>> rig_register (130) >>> rig_register (117) >>> rig_register (119) >>> rig_register (118) >>> rig_register (126) >>> rig_register (133) >>> newcat_init called >>> rig:rig_open called >>> newcat_open called >>> newcat_open: write_delay = 0 msec >>> newcat_open: post_write_delay = 5 msec newcat_set_trn called >>> newcat_valid_command called cmd_str = AI0; >>> write_block(): TX 4 bytes >>> 0000 41 49 30 3b AI0; >>> newcat_get_vfo called >>> newcat_valid_command called >>> newcat_valid_command: 'FT-991' command 'VS' not supported Opened rig >>> model 134, 'FT-991' >>> Backend version: 0.22.1, Status: Alpha >>> >>> Rig command: >>> >>> On 03/01/2015 08:48 PM, Michael Black wrote: >>>> rigctl-wsjtx -vvvvv -m134 -r<com-port> -s<baud> >>>> --set-conf=serial_handshake=Hardware f > > ------------------------------------------------------------------------------ > Dive into the World of Parallel Programming The Go Parallel Website, sponsored > by Intel and developed in partnership with Slashdot Media, is your hub for all > things parallel software development, from weekly thought leadership blogs to > news, videos, case studies, tutorials and more. Take a look and join the > conversation now. http://goparallel.sourceforge.net/ > _______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel > -- Chuck Forsberg WA7KGX c...@omen.com www.omen.com Developer of Industrial ZMODEM(Tm) for Embedded Applications Omen Technology Inc "The High Reliability Software" 10255 NW Old Cornelius Pass Portland OR 97231 503-614-0430 ------------------------------------------------------------------------------ Dive into the World of Parallel Programming The Go Parallel Website, sponsored by Intel and developed in partnership with Slashdot Media, is your hub for all things parallel software development, from weekly thought leadership blogs to news, videos, case studies, tutorials and more. Take a look and join the conversation now. http://goparallel.sourceforge.net/ _______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel
